Ford F-150 - 1997-2003 :: 2001 - Running Rough When Cold / Stalling Out When Coming To A Stop Light
2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.
Ford F-150 - 1997-2003 :: Clunk When Coming To A Stop
I'm getting a CLUNK when coming to a stop with my truck.
If I shut off the overdrive while coming to a stop it doesn't do it. Or if I manually shift it down a gear.
I read on here it could be a U-joint or the yoke or something and maybe something needs greased.
Anyway I crawled under the truck and it looks like I need a special socket to remove the 4 bolts holding the driveshaft to the rear end.
What type of socket it this? No grease fittings on my U-joints. What's causing this CLUNK as well?
Ford F-150 - 1997-2003 :: Truck Wants To Stall When Coming To Stop
I have a 2000 f150 with 210000 miles. The truck wants to stall when coming to a stop. I have noticed this from a higher speed and more when at operating temp. The truck runs great and idles at a stop great, but when coming to the stop the rpms drop to300 or so then it catches itself and revs up. I have cleaned the maf sensor the iac and checked throttle body all seem to be in working order and no obvious vacuum leaks.
My power steering pump is going and it's time to change plugs, but don't believe these would only effect the truck at braking. Have heard maybe torque converter is stuck this does make sense cause usually happens after getting out of first gear. Would changing the fluid solve this or should i look at sensors? Fluid starting to turn slight brown probably been in there 80000 miles.
Ford F-150 - 1997-2003 :: 2004 - ABS Engages When Coming To Stop
I have a weird problem that just started concurring. When you approach a stop and the vehicle is almost at 1 or 2 MPH, the pedal pulses and I can hear the ABS buzzing. None of the wheels are slipping, and all my tires are of the correct size & pressure. There is no ABS codes at all. There is no ABS light on either. How can I diagnose? 2004 Heritage.....
View 2 RepliesFord F-150 - 1997-2003 :: 1999 - Idle Hangs When Push The Clutch In While Coming To A Stop
I have a 1999 f-150 4x4 4.6 5spd manual 180,000 miles on the clock. My question is, when coming to a stop i push the clutch in an the idle hangs at about twice what it should be until i come to a complete stop then it drops to normal. It's not like somethings sticking cause it will stay at the high idle as long as were rolling but as soon as the wheels stop turning it drops down.
View 2 RepliesFord F-150 - 1997-2003 :: Pedal Was Rock Hard When Hit The Brakes Coming To A Stop Light
I have a 1997 F250LD 4WD. I was driving and came to a stop light. I hit the brakes and the pedal was rock hard with what seemed to be very little travel. I pushed hard to get to a stop and the abs activated and I came to a slow stop. This has happened about 3 times over the last 1000 miles of driving. I see no ABS or Engine lights. Most of the time the brakes are normal. Pads are fine, fluid is fine. Brake booster seems to work fine, pedal is not mushy or hard to press other than the 3 or so times this has happened. Once this happens I can let off the brake and everything is normal. I have not found any vacuum leaks.
View 6 RepliesFord - Ranger :: Stalling When Began Driving / Going Downhill And Coming To A Stop
My beloved standard, 2000 Ford Ranger, with an estimated 170,000 miles on it, has a problem with stalling that keeps getting worse. 2 different garages have failed to fix this problem three times. Many parts have been replaced/checked (like battery, plugs/wires) and the fuel and induction system was cleaned, fuel pressure, Compression and engine vacuum were all fine. The Check Engine Light goes on and off all the time and does not seem to relate to the problem. When the last garage hooked it up to the computer, nothing related to the problem was identified, they reported. The invoice/report from them is attached to this posting.
My problem began about 2 years ago. The truck would only stall out when I first began driving, after about a mile, and only if I was going downhill and was coming to a stop. Then it would putter and choke and ultimately stall out completely. After my 30 minute commute (near highway speeds) the truck would then be fine the rest of the day, with no problems stalling when I drove to a meeting or out to lunch. Since it began, it has gotten steadily worse. Now, pretty much whenever I decelerate downhill, and come to a halt, it will stall out unless I leave it in neutral and keep fluttering the gas peddle to give it more gas. It even happens when I'm not going downhill. It does not happen when I first start driving, but after a mile or so, it happens almost whenver I come to a stop. It sounds like the truck isn't getting enough gas, and if I don't keep pumping it with signifcantly more gas, it will stall.
Once stalled out, if I try to start it up again immediately, it is VERY hard to make it start. I have to keep turning it over before it finally sparks to life. It sounds pretty awful. otherwise it starts easily. IF, however, I let it stall out in a parking lot at a gas station, for example, and I go into the store and make a couple quick purchases, when I go out to start the truck, it fires right up with no problem. It only has a VERY hard time starting up when I'm in an intersection and try to re-start it immediately after it stalls out.
The two different garages that have failed to fix it were both able to easily replicate the problem, so that was not an issue. Amount of gas in the truck and temperature outside are both irrelevant.
Suburban :: 96 - Intermittent Stalling Upon Coming To A Stop
I have owned this 96 k1500 5.7L Vortex Suburban for 3 years.
Problem: Intermittent stalling upon coming to a stop. When it stalls and I try to restart the engine, the starter can barely spin the motor. The timing is thrown so far advanced that it will literally fire the engine backward and grind the starter gear on the flywheel. I have killed about six starters so far. I took it to the dealership and after two weeks they are clueless.
So far we have replaced: TPS, Ignition Module, Cam sensor, Crank sensor, ECM, and perhaps a few other things I don't recall at this time. If it would stall and simply restart, I could cope with it. The only way I have found to get it to start is when it stalls, pop hood, unplug the power source to the ignition coil, turn key and spin engine over for a few seconds, replug the power source to the ignition coil, and attempt a restart. Usually I don't have to do this more than once or twice.
Golf V R32 :: Repeated Stalling When Coming To Stop
Last Thursday I was coming home from work and the first time I came to a stop the R32 began to buck just as I gave it a little gas. Tried stopping and starting it but it continued to do it the rest of the trip home. Fast forward to this morning (first time we've driven it since) and it completely stalled on my wife on her way to work. She managed to get it started and get it home. I drove it around the block and sure enough when it comes to a stop after moving it stalls. I was able to consistently get it to stall just by getting it moving and then coming to a stop. I scanned it for codes last night and got a couple of different codes. Ignore the photo-sensor one - I am fixing that just need to find what I did with it.
Note the address 17 stuff - 2 codes to do with failure of the fuel sending unit. Could this possibly cause the car to stall out?
Also, address 16 (steering wheel) - RossTech seems to think these codes mean a faulty ignition switch.
I've never done data logging before but I was able to capture one of the stalls with VCDS. What columns would be useful to see and troubleshoot?
Here's the link to the log
01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
[Code] ....
Jeep - Grandcherokee :: 2001 4.0L Started Stalling When Coming Up To A Stop
I have a 2001 Grand Cherokee 4.0L with 215xxx miles. It just started stalling coming up to a stop, but then it starts right up no problem. Engine idles a little rough and the gas mileage has gone down somewhat. The CEL came on a while ago, and the auto shop checked the computer code and said it was the neutral safety switch. I brought this up with a friend who had the same problem and he rebuilt his and said it was easy. So I was going to attempt it, but I can't find the darn thing. @ questions:
1)where is it? and
2)could the NSS be causing the stalling?
Toyota - 4Runner :: 1997 - Randomly Stalling At Stop Light
I have a 1997 Toyota 4Runner SR5, 6 cylinder with 188,000 miles. I love my car, it's treated me well over the years. About 2 months ago it started stalling at stop lights, etc. Basically, any time I came to a stop and it was idling while in gear. I start it right back up and when my foot's on the gas, it doesn't stall. After 10 times or so I learned that if I took it out of gear the RPMs went up a little and it didn't stall. About 2 weeks later the "check engine" like went on so I figured, now it's time to take it somewhere. So I took it to a mechanic that I've been to before and trusted (here in San Francisco) and he said, "oh.. it's probably just an idle adjustment" so I think, great, no big deal.
After a few days he said wasn't the idle and that after testing he found that all 6 cylinders were randomly misfiring. So he needed to change the spark plugs cause they were down to a bare nub. I figured, ok, it's about time anyway. He said it could also be the ignitor?, he didn't sound 100% positive, but told me there's probably something wrong with it since it's pretty old too and that's all he could think of. So he changed all 6 spark plugs and the ingintor and the engine light was still on. It was stalling less frequently, but still randomly stalling.
He then said he was going to have his Toyota specialist friend look at it. His friend couldn't figure out what was wrong either. Then he sent to to the Toyota dealer, they checked everything they could think of, but couldn't diagnose the real cause either. Apparently they even checked the "Dynamic Balancer"? I'm not even sure my car has one of those. They might as well have told me it needed a new agonculator (totally made up word) for all I knew. So they had my car for 3 weeks and finally I said, enough is enough, these guys can't figure it out. After 3 weeks of hearing how much money they spent on other people to figure out it, I finally said, let's stop the bleeding. The car still runs and doesn't stall that much. The last thing they tried was 2 series of a fuel injection flush (decarbonize)? So they did that with not a whole lot of improvement. They also managed to run all the gas out of my car and by the time I picked it up, the fuel light was on and I took it immediately to a gas station. No joke, they burned about 1/2 tank of gas and didn't refill it.
After 3 weeks and $1000, they come up with "we don't know what's wrong, but use Premium gas and it might fix itself". In the end they told me they were down to only one misfire, cylider #4. Also, the "check engine" light is still on. Since I've gotten it back it hasn't stalled, so there's an improvement. But I'm no closer to figuring out what's wrong that's keeping the check engine light on. Needless to say, I'm not taking it back to these guys.
Accent MC (2006-11) :: Check Engine Light / Stalling After Coming To A Stop
I have an interesting issue that happened today after filling up on the way home from work. I have a 2011 Accent; 5 speed manual with 3900 miles. I filled up my tank and then topped off a little extra (which I now know is a no no) after the pump shut off. I put the cap back on, and after getting a cup of coffee, cranked her up and started on my way home. I drove maybe 20 feet and after coming to a stop, the car stalled. I wasn't sure at this point if maybe I let off the clutch a little too much. I started right back up and drove another 20 feet to a stop sign, and she stalled out on me again.
This time, after starting right back up, I noticed the check engine light was on, and if the car idled, it stalled. This is where it gets a little interesting. I was maybe 5 miles from the dealership where I bought my car. So I made a quick trip to the dealership to see if they could get the codes to determine the problem. After parking at the dealership, I turned off the car, removed the key from the ignition for about 10 seconds, and then started up again for giggles. The check engine light is now gone, and the car doesn't stall when idle. I have an appointment to get my oil changed, and am wondering if the codes can still be pulled?
Stalling - Honda - Accord :: Stalls Unexpectedly When Coming To A Stop Or Slowing Down
2002 Honda Accord, 4 cyl., will stall unexpectedly when coming to a stop or slowing down. It will start to shake and hesitate as one is slowing down from 35+ mph, then will stall at the stop. Has some trouble restarting, but when it does, everything seems to be fine. No codes are left, and my mechanic suspects dirt or something similar is contacting the fuel injector(s) on a sporadic basis. I did replace the spark plugs as they were due at the time this first showed up, but it has happened twice since in a 3 month period.
View 3 RepliesFord F-150 - 1997-2003 :: Runs Rough And Stalls When Stop Or Rolling To A Stop It Would Die
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
Ford F-150 - 1997-2003 :: V8 Just Stops Without Stalling
I have a 2003 f150 2WD crew cab with a 4.6 V8 engine it has 178,000 miles on it. The other day after I started it to leave work it died on me without hesitation almost like the ignition switch was turned off I tried to restart and it would turn over but wouldn't start so I switched the ignition all the way off and it started right up, going down the road it did it again.
If I try to restart without turning the ignition all the way off it won't start but if I turn it all the way off it will start up first try, it has done it a couple times since and its the same way every time, where to start. My check engine light has been on for some time for something else so I don't know if it picked up a code or not I don't have a code reader to see if it has a new code...
Chevrolet - Tracker :: 2002 - Engine Start To Sputter And Come To Verge Of Stalling While Coming To Stop
I have an '02 Tracker and I've noticed if I have several accessories running, that my engine will start to sputter and come to the verge of stalling when I come to a stop. It happens if I have the heat/air and radio or charging my phone on together. What is the cause and/or remedy for this? I've changed the alternator a few yrs. back, but it still continued.
View 2 RepliesToyota - Corolla :: 1997 - Rough Idle / Stalling Noises While Stuck In Stop And Go Traffic
I have a 1997 Corolla with 150k miles.
I had my catalytic converter and flex pipe replaced this summer. Lately, my car has been idling rough. While stuck in some horrific stop and go traffic three weeks ago, it started to make noises as if it would stall out. It didn't, but it still sometimes makes those noises.
The car seems fine on the highway. No loss of power. I did think that the hood felt too warm on a recent trip, but the temperature gauge in the car showed no issue.
The car hesitated when I tried to start it last week, but normally starts fine. It was the first cold day of the year.
I saw some white smoke come out of the tailpipe last week. It only happened once. Coolant and oil levels are fine. The spark plugs look good.
The fill pipe has been leaking gas for several months. It leaks if the tank is more than half full and it drips a bit of gas when I fill up. Two mechanics have not been able to find the leak and have told me not to replace it until it is a problem, given the age of my car.
I took it to a mechanic today (not the one who replaced the cat). He told me that the rough idling is due to the new flex pipe being shorter than what was originally there. He assured me that the car is fine to drive long distances and that there was nothing wrong with it. There's no check engine light or anything on the dash to indicate a problem.
I should be relieved, but I'm not. I've lost confidence in my car. Can the stalling noises and rough idling be explained away by a changed exhaust system? Or are these signs of a problem about to happen?
Ford F-150 - 1997-2003 :: Truck Keep Stalling On Acceleration
my 97 f150 4.2L keeps stalling on acceleration. It ran fine this morning then my wife put 20 dollars of fuel in it and drove 30 miles to her destination with no problem. on her way back the truck started bucking bogging down and acting like there was a fuel problem but it didn't kill. I checked for codes there were none. I removed the fuel filter on the rail and replaced it with a new one. Now it will idle fine with no miss but if I give it gas it kills.
I checked the codes again there are none. I also checked to make sure there was fuel coming from the tank when I turned the key as well as making sure I heard the fuel pump kick on when I first turned the key.I am leaning towards water in the fuel,i didn't see any trash come out of the old filter, however I am not sure. I have a 175 mile commute to and from work.
Ford F-150 - 1997-2003 :: Lack Of Power / AC Stalling Out Truck
I have a 2003, 4.6 F-150 with 201,500 miles
I am having some A/C issues. It's just too hot out there.
#1 The truck has a lack of power when I have the A/C on. It feels like it wants to stall out in the lower RPM's. I loose power when I go 65mph+. The truck actually stalled on me yesterday in the parking lot. I turned off the A/C and it ran fine.
#2 I have to go over a 5000ft pass daily, I turn off the A/C when I go over it. Below the pass, the A/C doesn't work well and it's not as cold. But when I get over the pass, the A/C turns very cold. The pass is like a 3-4 mile stretch.