Ford F-150 - 1997-2003 :: 2002 4.2L - Surging Bad At Idle
I am having great difficulty trying to figure out why my truck is surging so bad in park or in gear at idle. I have to mat the brake while in drive to prevent me from ramming the car in front of me. It all started when I replaced the air filter. Everything I've read leads me to the EGR valve, but that has been bypassed.
View 14 RepliesFord F-150 - 1997-2003 :: 2002 - Idle Surging When Cold
My 2002 F150 (50,000 miles) 4.2 is surging when cold. I just got done replacing the pcv valve. I noticed it was running better so I cleared the service engine light, but now is surging when the engine is cold. I live in FL so it does not get that cold like up north. The following codes were the ones that the pcu put out, P1131, P1115, P0174 and P0171. I am leaning towards changing the IAC valve and maybe the oxygen sensors.
View 5 RepliesToyota - 4Runner :: 2000 - Engine Surging At Idle
I have a 2000 Toyota SR5 with a 6-cylinder engine. When I first start the car (cold start) in the morning it will run at high idle (1500-1800 rpm) for about 3-4 minutes. At this point, the idle will begin to drop, but then the engine starts to surge. It's a noticeable surge that bounces from around 900-1100 rpm. It almost seems like an electrical surge, but I don't believe that's the problem. After running the car for a while and it's fully warmed up to operating temperature, the surge goes away. My thoughts automatically went to the IAC (idle air control) or maybe a temp sensor?
View 3 RepliesFord F-150 - 1997-2003 :: 2000 V8 Running Rough At Idle And Check Engine Light On
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
Ford F-150 - 1997-2003 :: 4.6 Lumpy Idle When In Gear
Recently I just purchased a 1998 F-250 (light duty) with 11X,XXX miles on it. Up until today, it was running perfectly. However, today it started idling rough whenever I was at a light. This was only when I was stopped, in gear, with my foot on the brake. In neutral or park it didn't do it, and it stopped as soon as I gave it a little gas. No CEL either. I've looked around, and saw that it might just be "feature" of the 4.6. I also have seen to clean the MAF, but wouldn't that also give a rough idle when in park/neutral? Same with replacing the coil pack.
View 1 RepliesFord F-150 - 1997-2003 :: 1998 - Low Oil Pressure At Idle In Gear
I was driving home last night and when I stopped at a light in town, I notice the oil pressure dropped and the light came on. So I pulled over and put in park to check my oil. As I put in park the pressure went back up. I dropped it back into gear and it went back down. What could be causing this? I check my oil and it was full. I also notice when I put it in gear and speed up the pressure goes back up and stays there till I slow down again.
View 8 RepliesFord F-150 - 1997-2003 :: 1998 V6 - Loping At Idle / Almost Stalls While In Gear
I have a 98 F150, 4.2 V-6, 183,000 miles.. Lately, she's been loping at idle. Especially while in gear... almost stalls. Once revved up, everything seems normal. Still goes up hills fine if I get on the gas. The light was on, and I got codes for lean condition on both banks.. (P0174, P0175).
I already cleaned all the sensors in front of the intake.
The MAF was real dirty, and the IAC was full of soot too.
They both cleaned up nicely, but it didn't work.
I borrowed a fuel pressure gauge yesterday, and it showed 12 psi with the "key on, engine off".
It showed 29-30 @ idle, and only went up to 35 when I revved it a little.
The guy at the store said the range is supposed to be "30-45 psi with the ignition on", but I'm not sure if that means engine running or not..?
Either way, it looks like the pressure is on the low side, so I'm going to change the fuel filter next (and hope for the best).
If the fuel filter doesn't fix it, what should I go after next? And, is there a way to test the fuel pressure regulator before buying a new one?
Ford F-150 - 1997-2003 :: 2000 - High Idle With Codes
I will try to keep this short. Picked up a 2000 f-150 4.2 for my nephews first truck last night. Bought it blind against my better judgement, but the price was right. Got it home, odometer didn't work, fixed the solder joint and was happy it only had 132k on it. Heater core was plugged solid. Got it flushed and at least now its has luke warm heat until I have time for a full coolant flush and new core.
Next on my list is the high idle and engine lights. Its idles around 1300-1700, cold or hot sometimes it drops down. I only have a cheap scanner, but I have 2 codes. PO171 and PO174. Where should I start with diagnosing this? I would assume vacuum leak. Any common spots to check on these?
Ford F-150 - 1997-2003 :: 2000 - Rough Idle When Outside Temp Below 50
2000 Ford F150 1/2 ton 2x 5.4L... Last year, I started having a problem where when the temp dropped below 50 degrees outside, my F150 would idle really rough and sometimes stall out. The CEL came on and reported some codes that I don't remember but pointed to bad air/fuel mix. I consulted a friend and he suggested changing out the IAC. I did that just towards the end of the cold weather spell we were having and the engine ran great so I assumed it was fixed.
Well, the temps have been below 50 for 8 days now and ever since the temps dropped the problem has come back. I took it to AutoZone to have the codes read and they gave me the following:
P1151 - Lack of O2 switches -bank 2 sensor 1 : ECM could not adjust fuel trim because of a lean or rich condition
AND
P0171 - Fuel trim bank one condition : The powertrain control module uses the oxygen sensor to calculate the Air/Fuel ratio of the engine. The computer recognized a rich or lean condition on one engine bank only.
Both printouts that they gave me mentioned the following:
Poor fuel pressure
Bad or Malfunctioning MAF sensor - Dirty/defective
Oxygen sensor defective
Fuel injector problem - Leaking or fuel pressure high/low
Vacuum leak on engine
I again called my mechanic friend and he suggested cleaning the MAF and if that didn't work replacing the MAF. I cleaned it and the problem was better but still not fixed.
Ford F-150 - 1997-2003 :: 2000 - Won't Idle Properly When Cold?
I have a 2000 f150 lariat 5.4L 4x4 and when i start my truck up when it is usually below 40 my truck will idle around 300rpm and shake. It also makes popping noises in the exhaust. I am getting codes PO171 and 174 (running too lean in both banks) I have replaced my IAC, plugs, pcv valve, air temp sensor and MAF sensor and 02 sensors and nothing has changed. I have tried looking for for vacuum leaks using carb cleaner and starting fluid but i nothing has came up. I took it in to a mechanic and he suggested a bad intake manifold but i searched for a leak and found nothing.
View 14 RepliesFord F-150 - 1997-2003 :: 2000 - Trans 3rd Gear Out / Revs Up But Does Not Pull At All
I recently purchased a f150 with a reg cab short bed 4.6 4x4, and when you put it in drive the it shifts up to second fine, but when goes to third just revs up doesnt pull at all. Have to shut o.d. off and goes steady but run 2500 rpms to go 40 mph. I was told to check the solenoids but i dont know, if i do need a new trans how do i identify my trans. I know it has the code "U" on the door sticker, but its an 4r70 w code-w. But the junk yard has a YL3P-FA and a YL3P-JA?
View 1 RepliesFord F-150 - 1997-2003 :: 2000 - Little Hard Jump When Shifting From 1st To 2nd Gear
I have a 2000 F150 with the 4.6L engine and I have a question about the transmission. When shifting from 1st to 2nd gear there is sometimes a little hard jump when shifting. All the other shifting through out the range is buttery smooth. The issue has been around for a long time and has never gotten worse. Is there anything simple I can do to fix this. Do those tranny additives work at all? Otherwise, I will just continue to live with it.
View 2 RepliesFord F-150 - 1997-2003 :: 2000 V6 - Ticking Sound At Idle But Not When Moving
2000 f150 v6... I just got the truck and was fine went to instant oil change and changed the oil used 5w30 and there filter unknown brand? now I'm getting a ticking kinda like a lifter tick?? you can hear it at idle not when moving.. Would the thicker oil be causing this? or the cheap filter is so filter should I go to? Motorcraft? bk to factory oil?
View 1 RepliesFord F-150 - 1997-2003 :: 2000 5.4L 4x4 - OD Hard Shift / Slams Into Gear When Give It Little Gas
I have a 2000 F150 5.4l 4x4. When I am going over 50 on the highway and I am in OD, if I let off the gas a couple of seconds later it feels as though the brakes come on because the truck slow down so drastically and when I give it a little gas it slams into gear. It feels as like there is a "gap" where nothing is engaged before it slams back in. This is a rebuilt tranny with less than 7K miles on it. I took it back once and they said it was the motor mounts. I had those replaced and still the same problem. I replaced the spark plugs 6K miles ago and the COPs 3K ago. There is 170K on the truck. I only drive about 8K miles a year.
View 2 RepliesFord F-150 - 1997-2003 :: Surging When Only At A Very Min Throttle
I have been fighting this surging issue for a while. I noticed when it starts to surge i could turn off the a/c and it would quit. It only surges when i am only at a very min throttle. Does this make sense? What can I do to fix it?
1999 f250 4x4 auto 256K miles....
Ford F-150 - 1997-2003 :: 2000 - Rough Idle / Codes PO304 And PO174
I have a 2000 F150 4.2L and I have 2 codes PO304 & PO174 so far I have changed my plugs & wires,fuel filter,mass air flow sensor, and coil pack...it is still running rough under a load and a little rough on idle..
View 9 RepliesFord F-150 - 1997-2003 :: 2001 - Shudder And Surging Upon Acceleration
When I first bought my 2001 f150 a few mos ago there were no problems but I did notice once in a while it would give one little shudder when id accelerate. now all the sudden it shudders after around 20 mph all the way up to whatever the speed limit is. Then it smooths right out until I have to accelerate again. if I punch the gas and kick it down it will clear up but then it feels more like a surging going on.
I had the cruise set at 70 the other day and I had to slow down to merge to around 50 and when I hit resume it really started shaking bad and the service engine soon light flashed on and off for a few minutes then went off and hasn't came back on again. I took it to advance auto and no codes showed up. they said its probably the torque converter but after reading multiple forums I am not so sure now.
Ford 7.3L Power Stroke (1999-2003) :: Idle Surging / RPMs Will Drop By 300 Or 400 For A Few Seconds
My '03 7.3 is "surging" on idle. When warmed up, and idling, the RPMs will drop by 300 or 400 for a few seconds and then will correct and shoot back up. It cycles like this (every 5 seconds-ish) continually . I just put in a new IDM and checked the UVCH - is there a separate idle control mechanism that I need to have a look at? (2003, 7.3, 214K, stock).
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 - Surging And Rough Idle While Driving
I have an early 99 F-350 with 268K miles. It is bone stock right down to the factory exhaust. A couple months ago I started have a rough idle and surging while driving problem. I never got a check engine light but I borrowed a scan tool from a friend and pulled the following codes: P1690 (wastegate solenoid), P0381 (glow plug circuit malfunction), P0269 Cylinder 3 Contribution/Balance Fault, and P0284 Cylinder 8 Contribution/Balance Fault.
I did some research and everything I read said it was most likely the CPS. So I changed the CPS. The truck ran fine for for a few days but then it started acting up again occasionally. I noticed that most of the time when it acted up was at start up when the engine was cold and I also figured out that if I shut the truck off and re-started it (sometimes I had to do it 2 or 3 times) it would clear up and run normal.
A buddy of mine that has a 2000 F-250 said he had a similar problem with his truck and it ended up being the ICP sensor. We switched his ICP with mine and I changed my oil at the same time (because it was due for an oil change). My truck ran flawless for over 2-weeks (over 200 miles) so I put a new ICP in my truck. Note: my buddy did not experience any problems with his truck with my ICP in it.
I've put about 700 miles on the new IPR and the truck has started to act up again. Once again shutting the truck off & re-starting it will clear it up and still no check engine light. I took it to a local "diesel specialty shop" while it was running rough and they hooked it to their scanner and got P1280 (Inj. Control Pressure Low), P1690 (Wastegate Solenoid Fault), P0381 (Glow Plug Indicator), P0269 Cylinder 3 Contribution / Balance Fault, and P0284 Cylinder 8 Contribution / Balance Fault.
They never did anything other than hook it to a machine & check the codes but their diagnosis is my High Pressure Oil Pump is going bad and my #3 and #8 injectors are going bad. They recommended I let them replace all 8 injectors and the High Pressure Oil Pump. The problem I have is they can't give me a REASONABLE explanation as to why re-starting the truck a few times clears up the problem.