Ford F-150 - 1997-2003 :: 2000 - Rough Idle / Codes PO304 And PO174
I have a 2000 F150 4.2L and I have 2 codes PO304 & PO174 so far I have changed my plugs & wires,fuel filter,mass air flow sensor, and coil pack...it is still running rough under a load and a little rough on idle..
View 9 RepliesFord F-150 - 1997-2003 :: 2000 V8 Running Rough At Idle And Check Engine Light On
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
Ford F-150 - 1997-2003 :: 2000 - How To Recalibrate The Temp On Overhead Display
How to recalibrate the temp on the overhead display?
View 9 RepliesFord F-150 - 1997-2003 :: 2000 V8 - Location Of Coolant Temp Sensor?
Where exactly is the coolant temp sensor located on a 2000 F-150 4.6 V-8.
View 5 RepliesFord F-150 - 1997-2003 :: 2000 - Replacement For Temp And Compass (interior Center Ceiling)?
Is there a replacement for temp and compass (interior center ceiling)?
What is the last year a Ford F150 was made with 16 inch tires?
My dear husband is not computer savvy.
Ford F-150 - 1997-2003 :: Rough Idle At Start Up
I just acquired a 2003 with 5.4 L. Did all new plugs and coils, cleaned MAF sensor, changed air filter, oil, transfluid and filter (obviously not related).
Upon start up and idle the truck has is rough, enough that it will vibrate the whole truck SLIGHTLY. Once in gear and warm, it smooths out and is fine. Unit the next stop and start.
Ford F-150 - 1997-2003 :: Idle Very Rough Like A Misfire
I got a 97 f150 4.2l from my neighbor. he takes good care of his vehicles. he sold it to me cuz it started to idle very rough like a misfire. it is hard to start when cold spits sputters and pops. once started idles like it wants to stall, then will idle normally then back to rough. back and forth like that. runs like a champ when going down the road . check engine light was on took it to auto store they checked codes . said bad o2 sensors so i changed them. still same issue. neighbor changed coil packs checked spark plugs and wire. every thing fires good. i changed iac. still didn't fix problem. could this be a bad egr valve or sensor? if so how can i diagnose this? he also thought was a clogged cat and bored it out. tight budget can't afford to take it to a mechanic. Was told spray carb cleaner spray around engine to check for leaks that did nothing at all...
View 14 RepliesFord F-150 - 1997-2003 :: Rough Idle When In Drive
I bought this truck used and when it's in drive the engine idles rough and seems about to stall when the ac is on at a stop sign or red light.. I've tried it w/o the ac on and it seems a little better but not as smooth. Idle in park is fine.
When I should start looking? Spark-plugs? spark plugs wires, disturber cap, fuel filter etc...
Ford F-150 - 1997-2003 :: Engine Went Into Rough Idle / No Acceleration
I have a 2000 F-150 5.4 L. I was driving from home and seconds after the engine went into a rough idle that wouldn't let me accelerate. I scanned it and gave me multiple transmission trouble codes, about 15. I checked the wiring, the transmission fluid and it all looked good. So, what could be the problem?
View 3 RepliesFord F-150 - 1997-2003 :: Rough Idle / Engine Vibration
Bought the truck knowing it needed a little work because it sounded like a diesel when running. So I had the timing chain, tensioners, water pump, etc. replaced and that fixed that problem. Then, a couple days later, a spark plug blew out of the engine. So, I go to do a full tune-up to find out that 3 of the 8 cylinders already had heli-coils in them.
I pulled those three and bored out and re-tapped the cylinders using the Cal-Van inserts. This has worked beautifully so far. I also replaced all of the other plugs as well with double platinum plugs. I also replaced all COPs. This got the truck running again and it drives great. No loss of power whatsoever. It just runs like a dog at idle. As soon as I give it throttle it smooths out completely.
It seems like the problem gets worse as the engine starts to get up to normal operating temp. Basically, if I am idling, in gear or in park, the truck shakes pretty bad. It kind of feels like it's starved for fuel or barely missing. I do not have any codes though and if it is a miss, it is completely gone under throttle.
Other things I have replaced within the past couple of weeks:
EGR
EGR vacuum solenoid
DPFE
Both PCV elbows
PCV valve
Air filter
Harmonic balancer
Other things I have done:
Cleaned IAC
Cleaned throttle body butterfly (including EGR ports)
Checked TPS voltage
I'm sure there are other things that I am forgetting.
The idle seems low to me but I'm not sure what is considered standard for the 5.4l. Mine idles around 600 in park once engine is warm and the needle doesn't move despite the roughness felt. Just going by the tach, you would think that the idle was smooth as silk.
Truck info:
2000 Ford F-150 XLT
5.4L V8 2V
150k miles
Ford F-150 - 1997-2003 :: 2002 V6 Misfiring - Rough Idle
I recently picked up a 2wd 2002 F-150 with a 4.2l V6 that has just over 300k miles. The CEL is on and I'm getting P1131, P1151, P0316, P0305 and an occasional P0301. It has a very distinct misfire from around 1,000 rpm and smooths out between 1,500 & 2,000 rpm, the idle rpm occasionally bounces (sometimes enough to stall), and the idle is sometimes rough.
I have replaced the plugs, wires, fuelfilter, and replaced a leaking PCV hose. As I have changed things the symptoms have improved some but they are still there. While capturing some livedata it kept going out of CL and into OL Fault. When it would the idle quality was crap and the miss was much more significant. I would have to put it into D hold the brake and run the RPM's up to just over 1k to get it back into CL.
After I got done with the data stream at idle, I set the parking brake held the foot brake and put the truck in D then ran the rpm's up to around 1,200 & held it there. The truck stayed in CL but it would cycle between misfiring for 5 - 10 seconds then clear up and run smooth for 20 ' 30 seconds, every time it cycled there was an audible click that could be heard. Also, the AC was off the whole time.
Live DataStream @ Idle: CL
CalculatedLoad Value - 12.9- 14.1%
EngineCoolant Temp - 103degrees C
Short TermFuel Trim B1 - 32.8%
Long TermFuel Trim B1 - 0.0%
Short TermFuel Trim B2 - 32.8%
Long TermFuel Trim B2 - 0.0%
Engine RPM - 816 . 846
[Code] .....
Ford F-150 - 1997-2003 :: Rough Idle / No Power Under 2500 RPM
I bought a 99 f150 lariat 4x4 with the 5.4 from a guy who said that it needed an oil pump. He said it lost pressure coming into work, he turned it off and coasted in. I towed it home and replaced the battery and bought a new oil pressure sending unit just to be sure it wasn't that.
Those things are so hard to get to. Finally I got an oxygen sensor tool on it and it was only hand tight. Rather than take it off I just tightened it up and started the truck. The dash guage read normal but the truck was idling so badly. Steady at about 1000 rpm and tooth rattling. 1500 with the foot on the pedal it evens out but still rough. Not sure if this was a good idea but I took it around the block. No power under 2500 rpm. Barely moving even. Just felt like there was no throttle response at all and again very rough.
Got it home and parked it. Now I'm wondering what to do to fix the Idle and power problem. Where to start would be great. And input on the oil pressure sending unit too. I suppose I'll have to get under there and replace it at some point anyways.
Ford F-150 - 1997-2003 :: 2010 - Rough Idle Under Load
My daughter has a 2010 F150 with 5.4, when pulling her horse trailer or extended idling her truck starts running rough, so far her husband has changed the fuel pump and 2 coil packs, no luck.
View 3 RepliesFord F-150 - 1997-2003 :: Rough Idle And A Miss While Driving
I recently inherited a 99 Expedition 5.4 with 90k miles. I'm trying to fix it up so I can sell it. Like the title states, the truck runs rough but there's no check engine light on. I did some research and ended up replacing the PCV elbow and that made it run better for a while but now it's back like it was. It won't die, just a really rough idle and a miss while driving. I imagine it's probably a (or a few) coil pack(s), but I have no way of knowing which one(s) to replace. I would think that would illuminate a CEL though. I'm also having problems with the AC. Upon inspection, I found that the compressor clutch assembly was completely gone from the front of the compressor. I replaced the whole clutch assembly, then voided the system of Freon and refilled it to spec, still no cold air. The compressor clicks on and off like it's low on Freon but it can't be. I'd just sell it as is but in south Louisiana a working AC is a huge selling point!
View 1 RepliesFord F-150 - 1997-2003 :: Engine Running Rough During Idle And Driving
I am having a problem with my 1997 f150 4.2 v6. The engine is running rough at idle and while driving. It's running so rough that it vibrates the entire cab of the truck. I found water in the oil when I was trying to fix the problem. I have since had the heads redone and replaced all of the gaskets thinking this was the reason for the rough idling and rough driving. It wasn't; doing this fixed the water in the oil but still I have the rough running engine at idle and driving.
I have replaced the EGR valve, plugs and wires, pcv valve, replaced the coil pack, fuel filter and air filter (everything has been replaced with ford recommended parts because I have read that the engine I have doesn't like after market parts). While driving the engine vibrates and sound as if it's going in a cycle in a rhythmic sort of way (like a washing machine goes in a cycle), best way I can explain it. I have come to the end of what I think it is?
Ford F-150 - 1997-2003 :: 5.4L Motor Swap And Engine Has Rough Idle
2001 5.4L 4x4...Engine bought from reputable junkyard with 140K has new manifold studs, motorcraft spark plugs, and 8 coils (bought on Amazon).
No check engine codes...checked for vacuum leaks...And has rough idle.
Is there a reason it might have rough idle aside from blown motor? The mechanic was going to take it to get computer reflashed but not trying to throw money down the drain...
Ford F-150 - 1997-2003 :: Rough Idle - Right / Left Bank Too Lean?
I have a rough idle. I have replaced upstream o2 sensors, plugs, wires, fuel filter, dpfe sensor, cam sensor, and cam synchronizer. This has only moderately improved my problem. I still have the right bank, left bank too lean codes. Could it be something as simple but hard to find as a vacuum leak?
View 8 RepliesFord F-150 - 1997-2003 :: Rough Idle / Engine RPMs Go Up To 2k Before Dropping Down
1999 F250 LD with 5.4 w/ 225k miles... Was running perfect yesterday when I shut the engine off. Started back up about 20 minutes later and Idles was up and down and rough.( 400 - 900 rpms) Drove and ran fine except Idle. I know that those codes are for the o2 sensors but don't believe they're bad. I hear what sounds like a vacuum leak somewhere behind throttle body. Either IAC or EGR or it could be coming from the line that runs in beside the IAC valve to the air intake in front of the throttle body. Tried spraying water in those areas with no results. Could it be a bad EGR valve or a stuck IAC valve? I have also noticed that lately when I start the engine the engine rpms go up to 2k before dropping down. Would a bad IAC valve cause such rough idling along with the codes that I described?
View 7 RepliesFord F-150 - 1997-2003 :: Got Error Code P1000 - Idle Rough - CEL On?
What that means? The check engine light is NOT on but I looked for a code because my truck is idling rough, and when driving, when the overdrive kicks in, it vibrates really bad. As if a bad U-joint on your drive shaft. The truck has been in a field for about 5 months broke down so any clue? Haynes manual says nothing about P1000.
View 13 Replies