Ford Escape / Hybrid :: 2001 V6 - Rough Start / Cranks For A Few Seconds Then Fires Up
Alright I thought changing a fuel filter was fool proof but I changed the fuel filter in my 2001 escape v6. awd and now for some reason it wont start right up like it used too before the filter change. It cranks for a few seconds then fires up and runs perfectly fine it sits for a few hours same issue where as before the filter change it fired up fine every time, what did I do wrong. 2001 ford escape...
View 1 RepliesFord - Escape :: 2006 Have Spark / Cranks But Won't Start
2006 ford escape cranks wont start, I have spark and fuel....
View 1 RepliesFord Escape / Hybrid :: 2006 - Hard To Start Now Takes Between 3 To 8 Seconds To Actually Fire
Wifes Escape with the 3.0 has been progressively getting harder to start. It spins over just fine, but now takes between 3 to 8 seconds to actually fire. In the last six months the alternator, spark plugs, air filter have all been replaced. Engine runs perfectly, never stalls and seems fine in every other way. I've cleaned the throttle body and the IAC is working fine.
Did some troubleshooting and sure enough, we are getting no spark for a few seconds and the engine runs fine when it finally gets spark. Would this be the crank position sensor? Cam position sensor causing this? Not sure what is supposed to happen during the starting sequence in regards to what sensors are in being read by the PCM and then enabling spark.
Ford Escape / Hybrid :: 2006 V6 - No Start After Front Timing Chain Cover Replaced
I had the front timing chain cover replaced, ever since it hasn't started. It would turn over fast a couple times and then drag and then repeat.
Found out the "Tone ring" was warped, it's been replaced and now it just turns over and over and no start but it doesn't drag anymore.
We can smell the fuel, and pulled a plug and can see spark while turning over and I was told fuel came out the plug hole so there is fuel there.
Tried a new cam sensor, crank sensor and battery and no change. Is there something else in the removal and replacement of the front timing chain cover that could be causing this?
I'm not a huge believer in coincidence as the vehicle was running great before this job.
2006 Ford Escape
3.0L v6 w auto tranny.
Ford Escape / Hybrid :: 2006 V6 - Instrument Cluster Warning Lights Came On But Truck Doesn't Start
My Escape is starting to have starting problems. I go to start it and all of the instrument cluster warning lights come on, but the truck doesn't start. If I wait a little while, all of the sudden it starts but all of the sudden the cluster lights start flashing, the various warning beeps sound off, the emergency flashers go off, etc. This lasts anywhere from 5 to 10 minutes until everything resets and goes back to normal. What is causing this?
View 1 RepliesFord Escape / Hybrid :: 2006 XLT - Very Low Airflow From Vents
I'm getting very low airflow out of all of the cabin vents. I've already checked and cleaned/replaced the air filter and cabin blower fan and the ducting between the two, there's no obvious debris at the intake. The blower and resistor are working fine - when removed but left connected to the electrical, it starts up fine, is quiet, and changes speed appropriately when the fan speed in changed. I think there's either debris or something buggered in the system that controls the vents, but I'm not sure how to check that.
View 4 RepliesFord Escape / Hybrid :: 2006 - ECM Communication Won't Working?
I am working on a 2006 Escape that originally came in with a misfire. It had three bad coils, and they had burned out three of the coil drivers in the computer. It had a new computer put in, but will not communicate with the scanner now to program the keys. The old computer would still communicate, and the vehicle can be started and run on three cylinders with that computer, but unfortunately it needs to run a bit better than that. Is there something I am missing about getting communication with a new computer?
View 7 RepliesFord Escape / Hybrid :: 2006 - Ignition Key Sticking?
My wife's 08 Escape has an issue with the ignition key actually sticking in spots when turning to the start position, then we almost have to turn it back to the run position, it doesn't spring back like it used to, and should do. It's an 08 Escape, XLT V6 AWD, auto transmission.
View 4 RepliesFord Escape / Hybrid :: 2005 - Crank Over / No Start
I have a 2005 3.0 front wheel drive Escape that the kids normally drive and recently had a crank over/ no start condition in my driveway. I replaced the fuel pump about three months ago. Turned the key and couldn't hear the fuel pump so I proceeded to check the fuses and relays and everything seemed good. I also checked the inertia switch and it seemed ok as well.
I then checked for power at the harness right above the fuel tank and I had 12 volts on two of the four wires so I assume that I have power to my pump. I then took out the pump and had it replaced it under warranty. So I proceeded to install the new pump and I thought that I would hook the harness back up and just turn on the key for a second to be sure that the new pump is working and there was nothing to be heard. Looking for a wiring diagram/colors of the fuel pump?
Ford Escape / Hybrid :: 2006 Mariner Frequently Cuts Out
Friend just got a mariner hybrid car, Its quite nice but it keeps cutting out on them on the freeway, a message will flash saying pull over as soon as possible. they turn the key off then back on and it's fine for awhile. It's happened 3 times to them today and once in awhile before that. no codes have been thrown, the CEL light is not illuminated. they are Flummoxed on this issue as I am. Also, is there a way the door key pad code can be read? they did not get it with the car and they'd like to use it. Message shows as 'Stop Safely Now' .....
View 4 RepliesFord Escape / Hybrid :: 2006 - How To Remove Steering Wheel
Looking for info on how to remove the steering wheel on 2006 escape to get to cruise control switches and is there a self test you can do for cruise control functions like holding on button while you turning switch on as in other models ???
View 6 RepliesFord Escape / Hybrid :: 2006 - O/D Light Come On - Code P0741
I have a Mazda Tribute 2006 2.3. The O/D light would come on, drove it to a friends to scan the check engine light code, and the car almost made it there and then wouldn't remove in reverse, forward, or anything. Turn it off then start it up still wouldn't, then turned it off let it cool and it worked again for a little while.
The code was P0741, just the one code. Took it to a shop to have further tests, they seemed to think it was the clutch was worn and when the fluid heated it lost friction.
Pulled the transmission and thought why not do a Transmission rebuild? I have never done one but there was an awesome video on youtube of the guy doing it so I figured it couldn't be too hard and was just going to try my first rebuild.
According to the guy in the video you always need all new bushing, and we will get a rebuild kit with new clutch packs and the other stuff that comes with those, and sounds like it's a good idea to replace the torque converter.
The car is only at 85K and it looks like the transmission was rebuilt once before he got it at 80K. Maybe a bad rebuild?
Here are some pictures .....
The Input Sprag bearing was shredded and the bushing looks terrible. Can I just replace the bearing and the bushing? Is there any other damage I should be looking for because of this?
The forward planet you can so some eaten metal on the edge and 2 gears spin super smooth and the other 2 you have to push pretty hard to get them to turn. So new forward planet?
The shell's corners look a little rounded I wasn't sure how much was to much, can you tell from the picture if it looks like too much?
Input Sprag
Forward Planet
Sun Gear Shell
Ford Escape / Hybrid :: 2006 - Instrument Panel Goes Out Randomly
I have a 2006 escape 4cyl. 2 wheel drive. The instrument panel goes out randomly...
View 1 RepliesFord Escape / Hybrid :: 2005 - Idle Jumping Up And Down When Start Every Once In A While
I have a 05 escape hybrid with 75k on it. there is a slight problem every once in a while when it starts the idle jumps up and down and when it is put in reverse it has no power to move. you have to put the pedal to the floor....there are no codes and ford has had the car for a total of three weeks, nothing found and of course it did not act up for them..
View 9 RepliesFord Escape / Hybrid :: 2010 - A/C Not Working - Compressor Won't Start
She has a 2010 Escape 4-cyl and the A/C isn't working. It's miserable hot and she has small kids.
The compressor won't start. I put a gage set on the low pressure side and it's sky high, so it should be coming on at least. I also used a Launch scan tool on the OBD port and the HVAC control is commanding the compressor to start, so it's not that - which leaves the $300 compressor or the $9 a/c relay as the next steps. Unfortunately, I only see this car occasionally so I haven't really been able to get under it to check for voltage at the a/c compressor or see if it's a ground issue, etc.
I'd like to go after the relay next but can't find a a diagram I trust as to which one it is. I've heard mention that it's the WOT relay and also that there's an A/C Clutch relay. Any reliable schematic of the underhood fuse block and which position it's in? I took the cover off and they're numbered but there's no map. Also, what p/n is the relay? I'd like to just pop in a new one and see if it takes care of it.
Ford Escape / Hybrid :: 2010 - Hard To Get It To Crank When Try To Start
My wife has a 2010 Ford Escape. When we try to start it you have to push the key in REAL hard to get it to crank. It's been doing this for a while and seems to be getting worse. It took her 10 minutes before she could get it to crank earlier today. Our mechanic couldn't find anything wrong the first time we went in.
View 3 RepliesFord Escape / Hybrid :: 2005 V4 Will Not Start / Running Rough
So my wife's 2005 escape currently will not start. It was running rough so we brought it in to the shop to have the codes read. There was a bad MAF sensor code so we brought it home and were gonna replace the part the next day. The next day rolls around and it refuses to start. Swapped out the spark plugs which was much needed, replaced the valve cover gasket, which had also gone bad, and put in a new MAF sensor. It still refuses to start. It will turn over, but never starts. Also, the sound as it turns over doesn't sound right. It's hard to explain what sounds off about it, it almost has a "soft" sound to it. I can try to explain better if needed.
View 6 RepliesFord Escape / Hybrid :: 2006 - Rear End Came Loose From Rusted Frame
The rear sub frame fell out of her 06 Escape Hybrid. She found the recall for the 01-04's, was the problem fixed in 2004, or are later models subject to the recall and repair also?
View 2 RepliesFord Escape / Hybrid :: 2006 - Cruise Control Will Power On But Does Not Appear To Engage
I recently purchased the 2006 Mazda Tribute and the previous owner has confirmed the cruise was not working. What I have looked at:
Checked fuses
checked cable and connections
check connections at unit
What I have is the cruise will power on (light on dash comes on) but it does not appear to engage. I tried to use the diagnostics built into the car, where you hold the off button and turn the key on. I get a flash for off, and on, but do not get a flash when I push the resume button.