Ford Escape / Hybrid :: 2004 Vehicle Starts Right Up Dies / Stalls - Smoke From Rear Of Engine
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
Ford Escape / Hybrid :: 2002 4WD Stalls When Going Into Reverse
2002 3.0L escape 4WD, stalled twice on me when shifting into reverse after a complete stop. No CEL, truck started right up again....
View 4 RepliesFord Escape / Hybrid :: Stalls Once It Warms Up Like Ignition Is Switched Off
The car has 130K on the clock, and I don't know if she's had the plugs replaced, but the car has been stalling on her suddenly once it warms up, like the ignition switch is switched off. Then, once it cools down for a night, it runs again. If it only cools down for an hour or two, it will run but only for a few miles before quitting again. I'm thinking a sensor, pcm, or coils, but I'm hoping there's some way to narrow this down a little bit.
View 10 RepliesFord Escape / Hybrid :: Engine Stalls - Runs Fine After Key Cycle
2010 Escape with 74,000 miles. Backstory: This is my daughters car who is away at college about 300 miles away. About a year ago the engine started hesitating when driving and would stall to idle at highway speeds. She took the car in to dealer and they replaced the Throttle body under the CSP that had been issued just prior to the dealer visit. All was fine for about 3 months, then she reports that the car is doing the same thing. Check engine light briefly illuminates and goes right back off when this occurs. She is able to slip the car into neutral and it seems to correct the malfunction. Unfortunately she has gotten so good at this that she keeps her hand on the gearshift when driving. It seems to happen at various speeds with no warning and no lasting effects.
She came to visit for Christmas and I was able to replicate the problem after about 30 minutes of city driving, but not quick enough to take a picture of the wrench that illuminated briefly. I slowed to the edge of the road, put it in park and turned off the key (engine ran the whole time at idle). Cranked back up and good to go! She had the oil changed about a thousand miles ago, I replaced the air filter last night and she had to return to her house for work in the next couple of days. She said it happened 5 times on the way home last night.
Car has always been serviced regularly and was a certified pre-owned when we bought it in March or so of 2012. I also bought the extended warranty although that may be expired by now.
Her local dealer said they can't fix it if the CEL is not on or the problem is not occurring at the exact time they have it in the shop. Now, I am not sure but was under the impression that the computer would record any codes and store them even if the light went off and the car returned to normal.
Ford Escape / Hybrid :: 2003 - Stalls From Park To Reverse And Drive
My 2003 escape stalls from park to reverse and drive,not all the time but when warmed up. IAC motor replaced and still stalls.
View 7 RepliesFord Escape / Hybrid :: 2002 - Random Misfire Codes
I am having some ( Bad Luck ) with my 02 escape I been getting random misfire codes started checking over o2 sensors first, replaced one on bank 1 downstream, I have screenshots to look over along with codes....
View 3 RepliesFord Escape / Hybrid :: 2001 3.0L Engine Has A Miss - No Codes?
What to look for. 2001 escape 3.0 starts and runs but it has a miss and no codes came up yet . the engine will rev up but it really takes time to idle down . don't matter if its cold or hot it just don't want to drop to idle as fast as it should.
View 4 RepliesFord Escape / Hybrid :: 2001 - Stall After Fueling - No Codes?
I have a 2001 Escape 3.0 l 6 cyl. She stalls or almost stalls every time I fuel up. I found if I turn key but not to start, it only severely sputters and usually doesn't stall. Replaced EVAP canister (and all but dust separator inside), fuel pump, EGR valve, pcv tube, iac, upper gaskets, valve cover gaskets, seals, spark plugs, fuel/air filter, evap purge valve, fuel filler cap, ftp sensor, all ignition coils, checked for clogged fuel filler neck, fuel/vent hoses from/to evap canister...nothing worked.
There is a hose I cant get to that ends unattached just past fuel tank and near fuel vapor(?) "tee" under car. Seems to come from fuel tank. What is it? Just an overflow vapor hose? Should it be attached to something? Anyway, I suspect fuel vent hose or valve on top of fuel tank since my options are limited now. Have it running great (except this issue) with 260,000 miles so really don't want to spend mucho $$. No codes thrown.
Ford Escape / Hybrid :: 2005 - Only Stalls At Idle After Warming Up / Code PO446 And PO511
Posted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 RepliesFord Escape / Hybrid :: 2006 - At Idle Engine Run Around 1000 Rpm - Error Codes P0113 And P2196?
Have a 2006 ford escape, at idle the engine will run around 1000 rpm's and then regularly dip down 500 rpm's. Through the intake i can here a distinct "thwap" when the RPM's dip.
Only codes are
P0113 and P2196
Problems accelerating sometimes, Took it too a shop they said bad exhaust valve on the backside of the engine either 1-2-3. They said needed engine work, but said they didn't know where the bad valve was so i don't even know how the made the determination. Vac gauge at idle also indicates bad valve.
However, when i give it even the smallest amount of gas possible the engine smooths out and vac gauge reads totally normal and steady.
Ford Escape / Hybrid :: 2001 XLT V6 - Cold Start And Stutter / Codes Read P0171 And P0174
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
Ford Escape / Hybrid :: Check Engine Light Only Comes On After Motor Is At Higher Rev - Codes P0304 And P0316
A couple of weeks ago I got a check engine light. Pulling the codes I saw that it was a p0304 and sometimes a p0316. The first time this happened I check the spark plug cables and one was loose (cycylinder 4). Then last week my fuel pump died. since then I have gotten the two codes on a somewhat continous basis. I replaced the plugs (needed to anyway) and the problem did not go away.
The odd thing is that the check engine light does not come on at idle. IT only comes on after the motor is at a higher rev. The replaced plugs looked pretty normal, but the cylinder 4 plug had some carbon deposits. I am currently running injector cleaner in the gas. I may go ahead and replace the plug wires since the current ones are high mileage and it is not an expensive fix.
Ford Escape / Hybrid :: 2011 - Multiple Codes / Check Fuel Inlet Message When Vehicle First Turned On
I am running into some issues with my 2011 Escape 2.5L. I am pulling a total of 7 codes. Two codes keep repeating, which those are P0455 and P0457. And I am also getting a C1963. Accompanying the engine codes, my HUD is displaying "Check Fuel Inlet" when I first turn the vehicle on.
View 10 RepliesFord Escape / Hybrid :: 2004 - Headlights Always On When Running
Lights come on when the ignition is on, regardless of the position of the headlight switch. They shut off about 1 minute after the engine is shut off. The warning chime dings the entire time until the lights shut off.
I want the light to work with the switch and not come on all the time.
It is not just the daytime running lamps. High beams also work with the headlight switch in the off position, ignition on.
Ignition off, the headlights switch functions as it should.
I bought the Escape about 1 month ago. Dealer purchase so I don't know how to get a hold of the previous owner.
It only has 51,000 miles, very clean and all service records.
Ford Escape / Hybrid :: 2004 - Cannot Seem To Get Air Bled From Brakes
I had to replace all brakes because the bleeders were rusted in, wouldn't come out. So I bled and re-bled, but the brake pedal is still squashy and goes down too far if I have to stop from any speed. I even used my vacuum pump for evacuating air conditioning systems, pulled quarts of fluid through all the brakes-definitely no 2004 vintage fluid in there any more! Yes, I made sure to never pull the master cylinder reservoir empty, which would let in air. I always start from right aft and end up at left front, in order of bleed first. No leaks, the fluid level is always where I left it on previous session. I must be missing something...How can there still be air?
View 14 RepliesFord Escape / Hybrid :: 2004 - Stuck In Limp-In Mode?
Wife come home the other day after leaving for work with the truck no going past 20KM to 30KM.. After some investigating it seems to be in Limp - In Mode. There was a Check-Engine light & after further investigation found a Vac hose with a leak, repaired this & test drove. Same issue.... then there was a loud hissing sound from the engine area so I investigate & now found the EGR sensor (DPEF pressure sensor ) had blow a hose & fried the sensor.
New sensor was replace along with 2-hoses cleared the engine light but the truck still will not go more then 20KM or 30KM max.. I checked the EGR valve with vac pump & engine stalls or so the valve is good. I have left the neg cable off the batt to try & clear the Limp-In mode without success. Looking for a way to clear the limp-in mode or do I need to clear it with a scan tool?
Ford Escape / Hybrid :: 2004 - Loss Of Power With 6 Cylinder?
My escape struggles to reach 30 mph.. throttle position sensor code when scanned.Replaced the sensor but still barely any power check engine light hasnt come back on.
View 9 RepliesFord Escape / Hybrid :: 2004 XLT V6 - Power Loss / Vehicle Won't Go Over 30 MPH
I have a 2004 Ford Escape XLT V6 and I am experiencing a major loss of power in the vehicle. It idles smooth at about 1000rpm's but when you drive it , the vehicle won't go over 30mph and has a significant miss to it. I replaced the fuel filter, put in some Seafoam and took it for a drive and it still did not have any power and I blew out the EGR valve on the test drive. I replaced the EGR valve and the problem still remains. I hooked up a handheld computer to it and I got a P0300, P0304, P0305, P0306, P0316 and a P0355 error codes.
View 1 RepliesFord Escape / Hybrid :: 2004 - Doors Won't Unlock Either With Key Fob Or Keys
I noticed the lights were staying on after the switch is turned off and engine off. I thought the lights might just stay on for a few minutes, they were still on an hour later and now I can't unlock the doors with either the key fob or the key. Not sure what to do next.
View 4 Replies