Ford Escape / Hybrid :: 2003 - Stalls From Park To Reverse And Drive
My 2003 escape stalls from park to reverse and drive,not all the time but when warmed up. IAC motor replaced and still stalls.
View 7 RepliesFord Escape / Hybrid :: 2004 2WD Stalls Out - No Codes
2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
Ford Escape / Hybrid :: Stalls Once It Warms Up Like Ignition Is Switched Off
The car has 130K on the clock, and I don't know if she's had the plugs replaced, but the car has been stalling on her suddenly once it warms up, like the ignition switch is switched off. Then, once it cools down for a night, it runs again. If it only cools down for an hour or two, it will run but only for a few miles before quitting again. I'm thinking a sensor, pcm, or coils, but I'm hoping there's some way to narrow this down a little bit.
View 10 RepliesFord Escape / Hybrid :: Engine Stalls - Runs Fine After Key Cycle
2010 Escape with 74,000 miles. Backstory: This is my daughters car who is away at college about 300 miles away. About a year ago the engine started hesitating when driving and would stall to idle at highway speeds. She took the car in to dealer and they replaced the Throttle body under the CSP that had been issued just prior to the dealer visit. All was fine for about 3 months, then she reports that the car is doing the same thing. Check engine light briefly illuminates and goes right back off when this occurs. She is able to slip the car into neutral and it seems to correct the malfunction. Unfortunately she has gotten so good at this that she keeps her hand on the gearshift when driving. It seems to happen at various speeds with no warning and no lasting effects.
She came to visit for Christmas and I was able to replicate the problem after about 30 minutes of city driving, but not quick enough to take a picture of the wrench that illuminated briefly. I slowed to the edge of the road, put it in park and turned off the key (engine ran the whole time at idle). Cranked back up and good to go! She had the oil changed about a thousand miles ago, I replaced the air filter last night and she had to return to her house for work in the next couple of days. She said it happened 5 times on the way home last night.
Car has always been serviced regularly and was a certified pre-owned when we bought it in March or so of 2012. I also bought the extended warranty although that may be expired by now.
Her local dealer said they can't fix it if the CEL is not on or the problem is not occurring at the exact time they have it in the shop. Now, I am not sure but was under the impression that the computer would record any codes and store them even if the light went off and the car returned to normal.
Ford Escape / Hybrid :: 2005 - Only Stalls At Idle After Warming Up / Code PO446 And PO511
Posted earlier with my escape randomly stalling at idle. Getting a code po446 along with po511. Only stalls at idle after warming up and letting it set a while. When you go to recrank it that is when it won't idle or if it does its at 500 rpms or less. Also after driving it today it smells like rotten eggs. Replaced the idle control valve with no luck. What could cause this?
View 2 RepliesFord Escape / Hybrid :: 2004 Vehicle Starts Right Up Dies / Stalls - Smoke From Rear Of Engine
I just picked up a 2004 ford escape and information is difficult for me to obtain. Person I purchased from had all new suspension installed. Says it needs new transmission.
My indications: Vehicle starts right up dies/stalls with anything above throttle. Major lack of power. Was able to put in Reverse and it moved a bit and same as drive. Smoke from rear of engine. Seems like coolant dumping into exhaust. shake on exhaust you can hear slosh slosh in exhaust.
No engine trouble codes no lights on dash.
Am I looking at a headgasket? This has the 3.0 duratec v6 with the water pump belt driven by the cam on the driver side. Open up the oil cap there is the timing chain. serpentine belt is on passenger side of engine. There is no coolant/water in the engine oil but the coolant is disappearing FAST. no coolant on spark plugs that indicate its in the cylendars.
Was going to check compression but the compression tester I have only threads up to 14mm. to small for the hole. I can probably rent a tester with proper sizes if needed. Fuel pressure at the rail primes to 60 psi and stays there. Stays at 60 psi while running as well.
Ford Escape / Hybrid :: 2003 - Truck Will Not Move When Put It In Drive Or Reverse And Press The Gas
I have an 03 Escape that is very difficult to start after it rains, if I open the hood and let it dry out for a few days it starts fine, however if I put it in drive or reverse and press the gas it will not move... if I hold the brake while it is in gear and give it gas it does not rev up, however if I put it back in neutral or park it revs up. I normally cover the hood with a tarp to prevent this from happening however I was shutting the tarp in the door and a lot of water got in the floor board of the truck I sucked it all out, that night the radio started playing all on its own, I came out to the truck turned the radio off it stop went back in came back a while later and it was on again, so I pulled the fuse... but there are two buttons that stay lit on the radio the preset button 1 and 2 stay on all the time and I can not figure it out either. This is my beach truck I only use it for that purpose..however it is fall fishing time and I really want to go...
View 4 RepliesFord Escape / Hybrid :: 2002 - EVAP System Failure
I have a failure on the evap system of my 2002 Escape, and need the proper testing procedure for this particular purge valve. I was able to fix the purge valve on my 2013 Explorer, with no issue, but the Escape has a different type and I'm not sure I'm testing it properly. I want to verify the purge valve is working properly instead of just throwing parts into it. I know it is likely either the valve or the gas cap, but it could be something other than those two items, so I want to get the simple stuff checked out first.
View 3 RepliesFord Escape / Hybrid :: 2002 - Random Misfire Codes
I am having some ( Bad Luck ) with my 02 escape I been getting random misfire codes started checking over o2 sensors first, replaced one on bank 1 downstream, I have screenshots to look over along with codes....
View 3 RepliesFord Escape / Hybrid :: 2002 - Trans Won't Shift Into Gear?
I own a 2002 Escape, 4WD 4cly manual trans. A couple of days ago, when I left work I stopped at a stop light. I shifted out of gear while I waited for the light to change like I always do. When I went to shift back into gear, I couldn't. I found that if I turned the key off, with the clutch disengaged, I could shift into gear without a problem, start the car up and drive away.
Since the first time this has happened, it has happened a few more times, always when stopped, once or twice while slowing down to stop (low RPMs). Besides all that, the car shifts fine while driving.
Ford Escape / Hybrid :: 2002 - Cylinder Misfire When Hot And Restarted?
I have a 2002 Ford Escape, 6cyl FWD... 110,000 miles.
About a month ago I started seeing a misfire, which of course usually is a COP issue. I should buy stock in whoever makes those. Anyway, the code according to parts store monkey was cylinder 2 misfire, so I replaced the COP. That made no difference. I also replaced the upper intake gaskets and the PCV valve while I was in there.
So I started monitoring when it would happen, and of course got the actual code rather than taking the word of the monkey at the parts store. The code is P0352 Primary / Secondary circuit malfunction.
So after some research I find it could be the harness, it could be the PCM. The question I have is this misfire seems to only be when the motor is started after it's hot. What I mean is I can drive to work 10 miles, no problem. I can drive to Orlando 100 miles away - no problem as long as I don't stop on the way. The only time the misfire happens is when I start the motor when it's hot. So if I drive 10 miles to the store, then drive home before the motor cools completely I'll be coming home on 5 cylinders. If I wait 2 hours between stop and start I never have a misfire.
Does that jive with a true electrical problem? I'm no expert, but I don't understand why driving for 100 miles is fine, but 10 miles, stop start and 10 more is an electrical problem.
Ford Escape / Hybrid :: 2002 - Lower Intake Gaskets?
Are there any tricks I need to be aware of, or any maintenance threads on changing the lower intake gaskets on my 2002 3.0 V6 Escape? Still having high idle issues when hot, and have checked everything else. I changed the upper gaskets when I replaced the plugs and COPs some time back.
Anything I need to be aware of, or is this similar to changing the upper manifold gaskets?
Ford Escape / Hybrid :: 2002 XLT V6 - Battery Light Randomly Comes On
I have a 2002 Escape XLT V6 4X4. I searched the issue, but others' symptoms don't seem to be quite the same as what I'm seeing. Over the last few weeks, the battery light has randomly come on and off 3 separate times:
- 1st time, light came on at highway speed for about 30 sec and went out. Didn't come back on. Was during daytime, running DRL's, radio (no amp or subs or anything like that, and heater blower on low speed.
- 2nd time was two weeks later or so. Happened at night with just headlights on at around 55mph (RPMs about 2K or so). Again, stayed on for about 30 sec and went out.
- 3rd time was about a week/week and a half later, yesterday morning. Just running DRL's and radio. Light came on, flickered, came on, and then stayed on for a couple of minutes (all at highway speed). I noticed that if I disengaged the overdrive and got the RPMs up, the light would go out. I ran it out of overdrive for about 2 minutes like that, and the light stayed out. Speed limit dropped to 40mph, and the light came back on (lower RPMs at that speed, didn't run it in low gears). Light stayed on for 30 sec - 1 minute, and then went out on its own and has since stayed off.
I took it to Advance yesterday to have it tested, and the results were that it is charging at 13.9V under no load, and 13.87V under a load. The battery tested good, but the machine said it needed to be charged (it hasn't been acting low...car starts just fine).
I'm driving it to work today to see what it does next, and then getting it tested again on my way home. Has anyone here ever had similar symptoms as above? Does this sound like bad diodes in the alternator?
Ford Escape / Hybrid :: 2002 XLS - Clutch Or Trans Just Seized
My wife has a 02 Ford Escape XLS with a I4/manual trans, she has been saying it has been making weird grinding noises for a while but has not been able to replicate it for me to hear. Today it locked in gear and stalled, she can depress the clutch and start it, but can't take off in whatever "gear it thinks it's in" and it'll stall. To quote her.
So odds are the clutch or trans is toast, I'm more of a full size truck guy when it comes to doing work, what to look at? She's getting it towed and I have enough tools to do the job just not a ton of time this second to do the research, When I know more I'll add it.
Ford Escape / Hybrid :: 2002 - Stumble At 1k RPM In Park And Neutral
So my buddy has a 2001 escape. It has a shudder at 1k rpm in park and neutral. It's not nearly as noticeable in drive. I scanned it for codes and there isn't one. Ran a power balance on ids and it's straight. Doesn't miss during the shudder either. Has all new coils and plugs. I cleaned IAC. MAF. Ran sea foam through the engine. And there is Lucas oil conditioner in the oil and Lucan fuel injector cleaner in the gas. It runs amazing other than that shudder. What could it be ?
View 1 RepliesFord Escape / Hybrid :: 2002 XLS 2.0L - Slipping Trans Clutch
2002 Escape XLS 2.0L 4-cyl 5MT FWD. Slipping Clutch.
I've read here n there that the Escape clutch is a poor design & others have reported that a clutch repair doesn't solve their shuddering problem. After putting off the job for a while, I'd like to replace the clutch.
Here's a topic from here : Manual Transmission shudder / fill & drain access?
Ford Escape / Hybrid :: 2002 4WD - Engine Sputter When Accelerating
My daughter has a 2002 Escape 4WD with 3.0L engine.
Coming home from school a few weeks ago she experienced engine running rough on the highway when trying to accelerate. We ran the diagnostic on it and it revealed that #2 cyl coil was misfiring.
I've replaced all of the rear bank coils (in hopes that I wouldn't have to remove the intake manifold again anytime soon). I also replaced the connectors and weatherproofed them.
Replaced all the plugs while I had easy access too. This all went pretty smooth with exception of breaking 3 of the 5mm coil bolts off inside the valve cover. I've also replaced the upper and lower intake manifold gaskets.
It runs much better now except now on the highway, at 1800 rpm/55 mph if I try a gradual acceleration I get engine sputtering and it won't accelerate. If I push hard on the pedal it will downshift and accelerate normally right past this trouble spot. Other than this it idles and runs great.
I've noticed that the 3/4 in. vac hose on back of manifold is getting pinched closed about 70%. this is the hose that leads down to the top of engine just below lower manifold. I suspect this is the problem but cannot determine the root cause. I assumed it was the intake manifold gaskets but those are now replaced.
Ford Escape / Hybrid :: 2002 Not Turning Over After Changing Computer
I was having problems with my 02 Escape of misfire on cylinders. After doing a lot of checking, changing spark plugs, changing coils, ect, I decided that it could be the computer. So, I ordered one and put it in. When I turned on the key, all the gauges pegged and then came back to zero, but it acted like someone cut the power line to the starter. No click, no nothing. I checked fuses and they are fine. Even changed them around to make sure. Is there something that I have to do when you change the computer to get it to start? Had no problems with the starter prior, so it has to be something associated with the computer and changing it.
View 3 RepliesFord Escape / Hybrid :: 2002 3.0L - Thermostat Housing Leak
I set out to do a coolant flush but ran into an increasing number of problems. When I went to replace the thermostat I discovered one of the three bolts would not come out due to the inside thread on the thermostat housing being stripped. I purchased a brand new housing and O-ring.
When I reinstalled the thermostat (also Motorcraft brand) with the above O-ring and attached all the hoses I had a severe leak between the thermostat housing and the intake hose connecter. I diagnosed the problem as the O-ring slipping off of the lip or ledge inside the thermostat housing and not sealing all the way around.
The Motorcraft O-ring seemed like the diameter was too big for the interior lip of the thermostat housing because the ring would pop up on one side whenever I tried to fully seat it on the interior lip. I went to AutoZone and purchased an orange Duralast O-ring, and while it seemed to be a little smaller diameter than the Motorcraft it too slipped off when I tightened down the housing.
I have tried everything, and every time I tightened down the housing I did it very slowly and carefully doing an 1/4 turn at a time with the three bolts but still the O-ring would slip off.