Ford Escape / Hybrid :: 2001 - Code P0303 And P0171 / Cylinder 3 Miss And Lean Condition Bank1
Brought home tonight a 2001 Ford Escape 3.0L 24 Valve V6. Bought it from a mechanic who's customer didn't want to put any more money into it. Has 185000 miles on it and it throwing the P0303 & P0171 codes. Cylinder 3 miss and Lean condition bank1.
Mechanic thinks it is a valve seat in the cylinder head next to the fire wall. Before I start replacing the cylinder heads with new remanufactured heads I plan on doing a compression test and leak down test.?
Ford Escape / Hybrid :: 2001 - Stall After Fueling - No Codes?
I have a 2001 Escape 3.0 l 6 cyl. She stalls or almost stalls every time I fuel up. I found if I turn key but not to start, it only severely sputters and usually doesn't stall. Replaced EVAP canister (and all but dust separator inside), fuel pump, EGR valve, pcv tube, iac, upper gaskets, valve cover gaskets, seals, spark plugs, fuel/air filter, evap purge valve, fuel filler cap, ftp sensor, all ignition coils, checked for clogged fuel filler neck, fuel/vent hoses from/to evap canister...nothing worked.
There is a hose I cant get to that ends unattached just past fuel tank and near fuel vapor(?) "tee" under car. Seems to come from fuel tank. What is it? Just an overflow vapor hose? Should it be attached to something? Anyway, I suspect fuel vent hose or valve on top of fuel tank since my options are limited now. Have it running great (except this issue) with 260,000 miles so really don't want to spend mucho $$. No codes thrown.
Ford Escape / Hybrid :: 2001 XLT V6 - Cold Start And Stutter / Codes Read P0171 And P0174
I got a 2001 Escape XLT (V6) a couple of months ago. Its in great condition, only 82k miles on it too. It had the notorious door handle issues which I have had fixed. It also had the wet weather stuttering problem, which I had fixed by having all 6 spark plugs replaced (Motorcraft OEM plugs), the back 3 coils replaced, upper intake gaskets replaced, Valve cover gasket replaced, PCV valve replaced (motorcraft).
It runs great when its warm, the problem I am having is when its cold outside and the engine is cold, it starts up fine but idles like crap and if its really cold outside, it starts and dies 3 or 4 times before it can even get to the crappy, stuttering idle. I have to intermittently feed it gas to keep the cold idle going long enough (3 or 4 minutes) before I can drive it. Once the engine is warm it drives like a champ. The only warm engine issue, is occasionally after driving it and putting it in park, the engine will rev up to 2000, 3000+ rpms, and just keep going up until I shut the engine off.
The codes read P0171 and P0174, which are lean on bank 1 and bank 2. It had also thrown a misfire on cyl 6 but once I cleared that it hasn't come back, just the lean codes are still present.
From what Ive been reading, this can be a number of issues, ranging from the IAC valve, EGR valve, MAF or the lower intake gaskets. I'm very much a rookie when it comes to car mechanics, but I think I can handle changing the IAC, EGR and MAF since they are all on top of the engine. However I don't know if I could handle the lower intake gaskets. Ironically, the gaskets are the cheapest part, but the most labor if I paid someone else to do it.
If I replace the EGR, do I also need to replace the EGR Modulator as well? Looking for brand names that are best bang for the buck when it comes to these other parts I have mentioned?
Ford Escape / Hybrid :: 2006 - At Idle Engine Run Around 1000 Rpm - Error Codes P0113 And P2196?
Have a 2006 ford escape, at idle the engine will run around 1000 rpm's and then regularly dip down 500 rpm's. Through the intake i can here a distinct "thwap" when the RPM's dip.
Only codes are
P0113 and P2196
Problems accelerating sometimes, Took it too a shop they said bad exhaust valve on the backside of the engine either 1-2-3. They said needed engine work, but said they didn't know where the bad valve was so i don't even know how the made the determination. Vac gauge at idle also indicates bad valve.
However, when i give it even the smallest amount of gas possible the engine smooths out and vac gauge reads totally normal and steady.
Ford Escape / Hybrid :: Check Engine Light Only Comes On After Motor Is At Higher Rev - Codes P0304 And P0316
A couple of weeks ago I got a check engine light. Pulling the codes I saw that it was a p0304 and sometimes a p0316. The first time this happened I check the spark plug cables and one was loose (cycylinder 4). Then last week my fuel pump died. since then I have gotten the two codes on a somewhat continous basis. I replaced the plugs (needed to anyway) and the problem did not go away.
The odd thing is that the check engine light does not come on at idle. IT only comes on after the motor is at a higher rev. The replaced plugs looked pretty normal, but the cylinder 4 plug had some carbon deposits. I am currently running injector cleaner in the gas. I may go ahead and replace the plug wires since the current ones are high mileage and it is not an expensive fix.
Ford Escape / Hybrid :: 2001 - Engine Light Blinking And Misfires
I have a 2001 ford escape. Today it starts to miss and the engine lights starts flashing. It is never the same amount of flashes. Sometimes its 8 or 10 flashes. I counted up to 25 flashes one or twice It just shakes bad and that's when the flashing starts. When it starts to miss and vibrate, I can accelerate in passing gear and it smooths out. When you hold it at a constant speed it starts missing again. Cannot get a code with my reader. Someone told me a flashing light indicates a misfire. What may be causing this problem?
View 2 RepliesFord Escape / Hybrid :: 2001 - Engine Will Randomly Die When Lets Off The Throttle
Well, not an escape, it is a mazda tribute. but it is the same thing as an escape. My sister just called. as she is driving down the road, if she lets off the throttle the engine will randomly die. it did it 2 times sunday, once yesterday, and once today, as she was talking to me. It will not die at traffic lights, just as you let off the throttle sometimes. today it did it at 45 mph. When it dies she just pops it in neutral, restarts it, puts it back in drive, and it is fine. No check engine light after restarting. What I should look at when she brings it over this weekend?
View 3 RepliesFord Escape / Hybrid :: 2001 V6 Engine Will Try To Start When Turn The Key - No Power
My daughter has a 2001 Ford Escape, V6, Automatic, 2WDR, 132,000 miles that is having starting problems. When you turn the key the engine will try to start. You have to push on the gas pedal to keep it running, it will not idle until it gets warmed up. If you try to drive it while cold, it has no power. Reading previous posts I have already replaced the spark plugs, intake gaskets, air filter, EGR, TPS, and fuel filter. Check for crack hoses / vacuum leaks. It is still not starting properly. No engine codes. New problem is oil light is flashing but the engine has oil. All of the gauges, lights, functioning normally. What do I try next?
View 1 RepliesFord Escape / Hybrid :: 2001 Just Won't Run - Engine Sputters And Coughs When Step On Gas
2001 escape 3.0 engine is giving me a headache. It starts and will idle no problem but as soon as I step on the gas the engine sputters and coughs but it does race up. I put in new intake seals, new sparks plugs and a tps and cleaned the maf sensor. It shows no codes so what am I missing? Can it be a fuel system problem ?? what should I be looking for??
View 2 RepliesFord Escape / Hybrid :: 2001 Won't Idle After Starting - Cold Engine Misfire
I'm needing cold engine misfire. 2001 escape 3.0 engine 190300 miles on it. I changed the plugs, cleaned the fuel injectors, new air filter, new fuel filter, cleaned the pcv valve and new ideal control valve. When the engine is cold it starts right up but wont idle right and misfires sputters some to but run the rpm's up and it smooths out. drop to idle and it misses. Now when the engine gets to operating temp it seems to run fine. What am I overlooking to find the problem?
View 5 RepliesFord Escape / Hybrid :: Slight Miss Under Cruise / Goes Away Under Slight Throttle
2005 Escape 3.0 with 160k miles. Slight miss under cruise, goes away under slight throttle. No service history known about vehicle. Best to replace spark plugs and coils with Motorcraft parts? And the intake gaskets too? Suggestions for correct plugs?
View 14 RepliesFord Escape / Hybrid :: 2004 2WD Stalls Out - No Codes
2004 Ford Escape 2WD 3.0L with about 81,000 miles.
Problem: 2 possibly related
1) If warm up (get to about 190+ degrees) and then cut off engine. Does not start. If I wait about 30 secs and play the gas pedal, then I can get it to start with high revs and after about 15 secs runs normally. Or, I can disconnect the air intake and it'll start fine. But if you stop and try to start again, no joy unless playing with gas pedal.
2) After driving about 20-25 mins, it seems to randomly stall-out while going about 40 mph. When it stalls out, it will restart again after about 30 secs.
Note: Neither of the above throw any codes.
Here's my problem chart after mining the other posts:
Thing to replace/do //// No Code /// Stall while driving /// Won't restart when hot
Fuel Pump //// Yes /// Yes /// Doubt it
Fuel Filter //// Yes /// Yes /// Don't think so
CKP Sensor //// Yes /// Yes /// Yes
CMP Sensor //// Unlikely /// ? /// Possibly
ECT //// Maybe? /// Yes (if too hot) /// Yes
IAC Valve //// Unlikely /// Yes /// No
Thermostat //// Yes /// Yes (if too hot) /// Yes
MAF sensor //// Unlikely /// No /// Yes
What I've done:
- Well, I started looking at the vacuum lines and they were crumbling so I replaced all those (to EGR and all that).
- There is a mystery line that appears to come up from the canister and go to nothing--is this some kind of atmospheric vent?
- My cheap scan tool also shows engine temps getting up to 216 degrees if I make it work (idle high at 2000+ rpm), so I'm suspicious of the cooling system and thinking maybe the ECU is shutting down to avoid overheating.
I'm going to start with flushing the coolant and replacing the ECT and thermostat while doing so. This is relatively inexpensive and ECT can do weird things. The restart problem is consistent, so I'll know if I fixed that right away.
Ford Escape / Hybrid :: 2002 - Random Misfire Codes
I am having some ( Bad Luck ) with my 02 escape I been getting random misfire codes started checking over o2 sensors first, replaced one on bank 1 downstream, I have screenshots to look over along with codes....
View 3 RepliesFord Excursion :: 2001 V10 - Slight Miss When Cold / No Codes
I have a 2001 Excursion with the V-10. Two weeks ago, the upper nipple on the radiator cracked and I overheated. Was towed home and replaced the radiator with a quality aftermarket one. I then drove to the whiz wash and cleaned the antifreeze off of the engine.
Immediately I noticed a slight "miss" when cold, particularly when backing out of my driveway. I have no lights on the dash and it is throwing no codes. The miss gets much better (almost gone) when the truck is warmed up.
Ford Escape / Hybrid :: 2011 - Multiple Codes / Check Fuel Inlet Message When Vehicle First Turned On
I am running into some issues with my 2011 Escape 2.5L. I am pulling a total of 7 codes. Two codes keep repeating, which those are P0455 and P0457. And I am also getting a C1963. Accompanying the engine codes, my HUD is displaying "Check Fuel Inlet" when I first turn the vehicle on.
View 10 RepliesFord Escape / Hybrid :: 2001 - V6 Idle When It Gets Cold Outside
I have a 2001 Escape, V6 engine and I guess it really does not like it when it's cold outside. Usually the car runs just perfect but when the winter arrives and temps drop into the 20s the truck does not want to run idle right when I first start it. I have tried by stating it without touching the gas pedal. And also by pushing it all the way down and then releasing it. I don't know which method is the right one, but it doesn't seem to make a difference. It takes some time and eventually after about 5 miles of driving it will act normal again. What could I do to fix that?
View 9 RepliesFord Escape / Hybrid :: 2001 - Cruise Control Not Working
The cruise control has not worked on my 2001 escape since i bought it a few weeks back. i checked the usual culprits and everything is good. i plugged my scanner in and got a control module code.
c1945- park switch indicates park with vehicle moving.
I did do some live data testing and it does infact show park when in gear. the display on the dash shows the proper position.
I am almost certain this is the issue with my cruise. Where this sensor is? Doing a parts lookup isn't showing much.
Ford Escape / Hybrid :: 2001 XLT V6 - Stuttering Or Misfiring On Acceleration
I've got an issue on my Escape, and I'm at a dead end. '01 XLT V6 150K miles.
About a week ago, driving to work, it started stuttering or misfiring while accelerating up inclines. Cruising and idle were smooth with no issues. I found that if I let off the gas as it was stuttering, it would stop, and then I'd give it gas again, and it would be fine. It was pretty intermittent.
Opened the hood and the large vacuum hose that goes from the top of the intake down to the PCV, has an L boot that connects it to the intake. That boot was collapsed down on itself while the motor was running. It went back to normal when I shut it down. I felt the boot and it was very thin and worn out, so I replace the whole two piece hose, along with the PCV valve. The old PCV came out and was rattling, so I believe it was ok, but I installed a new one anyway.
Drove it after that and it still had the stutter. It was now also doing it just barely at idle. I'd hear the motor miss, and it would really start when I would give it gas. I thought it was still a vacuum issue, and that there were probably other bad hoses. I found two. There's a small hard plastic line that comes off the air intake hose from a T, and those lines go to the camshaft covers. The hard lines go to rubber boots on the cover, and the one in the back was in two pieces. Replaced it. No change.
The other line is a small rubber line that comes off a round component, (I still haven't found out exactly what this part is called), that is bolted to the drivers side shock mount, and has a couple soft lines coming off of it. One of the lines goes over the top of the motor and ties into a T right where that large PCV hose goes into the intake. The part is circled in red, and the arrows point to the hose in the attached pic.
Ford Escape / Hybrid :: 2001 - Replacing Main Bearings?
Is it possible to replace the main bearings in a 2001 Escape 3.0 with the engine in the vehicle?
View 1 Replies