Ford 7.3L Power Stroke (1999-2003) :: No Power - Truck Will Crank For About 15 - 20 Seconds Before Turning Over
I have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
Ford 7.3L Power Stroke (1999-2003) :: Truck Not Starting When Cold / Would Not Crank Up
I had issues with my F250 cranking last winter when the temperature dropped, so I changed out the glow plugs in the spring. I hadn't been able to truly test them yet, since it hasn't been cold, but the other morning my truck wouldn't crank up. It was 40 degrees out the night before, and it had been almost 24 hours since I cranked the truck, but it seems to me like the truck shouldn't have an issue in that mild weather.
I'm not sure what I need to do next to try and fix this problem, it's been driving me crazy and risks stranding me if I park for a while in an area where I am unable to plug by block heater in. The truck cranks fine when I have had it plugged in for a while, so I'm fairly certain it's a heating issue. I haven't done any tests since last year, but I know that the GPR was working properly last winter, which is why I changed out the glow plugs.
Ford 7.3L Power Stroke (1999-2003) :: CEL On - Long Crank / Truck Starts Losing Power And Eventually Died
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
Ford 7.3L Power Stroke (1999-2003) :: Truck Keeps Dying And Have To Crank For About 15 Seconds To Start Again
Alright, my 1999 7.3 keeps dying on me in the morning. About two weeks ago I noticed it started to have a weaker start up, even though it has two brand new batteries. Once it starts up, I get around the block and it dies there every time. Then I have to crank it for about 15 seconds for it to start again.
The crank gets faster and faster until it finally start, and the engine is very choppy, like its starving for fuel. After about ten seconds of that it return back to a smooth idle. I then take off, and about 50 yards later it does the same thing. After it does it the second time, the truck runs just fine for the rest of the day with no problems.
I have noticed that when if I turn the truck on and let it idle for 10 minutes first in the morning, it won't die on me. I replaced the camshaft position sensor thinking it was that, but it wasn't.
Ford 7.3L Power Stroke (1999-2003) :: Block Heater Plugged / Truck Crank But Won't Start - Fix?
When the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.
Ford 6.0L Power Stroke Diesel :: 2003 F250 Truck Will Not Start / No Crank
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Truck Won't Crank Anymore After ICP / Oil Cooler Repair
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
Ford 7.3L Power Stroke (1999-2003) :: F250 - Truck Would Die While Driving The Truck
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Hard To Crank - No Power?
Iam looking at a 2000 7.3 Powerstroke that has some problems first it is hard to start cranks like it has a dead cyl. Second after starting it has no power not even enough to move. At first it would only run if held wide open but once it warmed up it would idle and rev and move but barely still had a miss. The weird thing is it did not smoke blue-black or white also no strong smell of diesel and no smell of oil at all. The truck has 230ish miles and there are no maintenance records.air filter was new.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Won't Crank When Key Turned On?
I have a 1999 7.3 super duty that won't crank when the key is turned. All lights work, power windows and mirrors work but after the WTS light goes out... Nothing...now I do have a slight leak in the roof and a little water does get in the cab. I opened my door the other day and it smelled like an electrical fire had occurred. I checked under the hood and the same smell, if not a little stronger. I pulled my fuse box and GEM tonight. Once I got away from the truck, I expected them to smell like the electrical fire smell, but they didn't. Now I did try cranking the engine over by jumping the starter relay before tearing the fuse panel out, and I got it to crank, but not strong at all. The batteries are good.
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 Won't Crank At All / When Turn The Key To Start Power Drops
New to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
Ford 7.3L Power Stroke (1999-2003) :: Cold Crank No Start
I have an 02 f250 230,000, first 7.3. I've owned it since Oct and put less than 6,000 miles on it. I have another cold crank no start. New glow plugs and Glow plug relay last weekend. Worked fine that weekend. It sat all week, then crank no start fri night, it was like 70 degrees for the high that day. Plugged it in over night and it started. Did not fire right up cranked it for a couple seconds. I drove it all day, started every time. Valve covers have 5,000 miles on them. Fuel Filter heater fuse not blown. But don't know how to check it for sure. And don't know where to go with it from here. Getting frustrated with crank no starts. No troubles found.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Crank But Won't Start
I got a 2000 7.3l with 400,000 miles on it that decided to just not start anymore after I parked it for a couple days. Its always been a hard starter due to needing glow plugs but I can deal with that. it doesn't even try to fire anymore. I replaced the CPS (my tack bounces when cranking). The ICP has oil in the plug so I just unplugged it for now till I replace it.
I pulled the IPR and cleaned it really good and bench tested it with 12 volts and could here it clicking so I put it back in. I can get under the drivers door with the key on and hear the fuel pump running. I gain oil pressure on my dash gauge when cranking. I check all my fuses. my WTS light comes on . I just don't have any fancy scan tools to make this easier. Also just cause I was feeling lucky I just went out and bought 2 new batteries for it yesterday so we are good there.
Ford 7.3L Power Stroke (1999-2003) :: 1997 - Crank But Won't Start?
I have a 1997 F350 7.3 with standard xmission. Have not messed with it since Oct of last year. Then it would crank but no start. Now when I turn the key there is no wts or nothing the gauges move, and tach moves when cranking, but nothing else.
The cam and crank pos sensors have been changed. The high pressure sensors changed. Now when I hook it to the AE it says cannot connect to truck. Where I need to start? Have checked all fuses that I know about.
Ford 7.3L Power Stroke (1999-2003) :: Won't Start / Just Crank And Tried To Fire
Friend's 2000 7.3 wont start, just crank and crank tried to fire but nothing in the cold leave it plugged in and it starts leave it in a shop over night and it starts with a shot of either, he is a truck driver and the truck will sometimes sits for 6 weeks at a time this time 2 weeks before I touched it. He wanted me to install a fuel pump so I did and started the following:
Cracked fuel lines to see if I had fuel psi at both heads
I tested glowplugs they all read at 0.3 on all 8
I have power to harness as the same at both sides of the relay
RPM tach jumps
Oil psi gauge rises
Using my phone I can read hpop and 2000 at cranking (how accurate that is im not 100% sure)
All fuses good
Ford 7.3L Power Stroke (1999-2003) :: New Injectors - Crank But Won't Start - Low ICP?
So I got all 8 injectors upgraded and excited when I get them back I put them all in in kind of a rush. And in that rush I left the cylinders full of excess oil. So obviously when I tried to start it hydro locked. Angry at myself. I kept trying to crank hoping it would fire and just shoot that oil out. Nope, so I went back to taking all the glow plugs out and firing it all back out. Put it all back together then tried to fire her up. Took a minute but she started and I let it run for a while. Hit the gas a few times and then it died. Couldn't get it started again. It would just crank, I checked the icp and ipr and the icp did not build above 35 psi and the ipr was at 98.04% so I just figured the o rings blew out when it hydro locked.
So I took it all back apart put new o rings on, took my time and put it back together right double checking everything. Got it all back together and went to start it, it would just crank around 160-170 rpms, battery voltage at 10.6 icp built up to 140 but now it won't build past 40. Ipr still goes to 98.04. The engine ran just fine prior to injector change, I put a new upgraded hpop prior to injector change, new ipr, icp, cps. Everything checks out, but it will not build oil pressure while crank I've killed a set of batteries then went all out and spent 350 at napa for some optima red tops. I did notice the cylinder 7 injector is the AE injector. It suppose to be in cylinder 8, idk if that's affect the oil pressure building up?
But as far as I know, I'm not building oil pressure. So idk if the hydro lock could have ruined something to keep it from building oil pressure?
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Crank But Won't Start?
i have a 2001 f250 7.3L PSD. it turns over but will not run. replaced the CPS , starter and the #30 fuse. IPR is new and all injectors are new, new gaskets and harness and new glow plugs new batteries. still just cranks and cranks. no oil pressure build up and no tach movement, oil level is good in HPOP. What could it be?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Just Crank When Try To Start Cold
So back ground is as such. Truck started fine before I replaced the hpop with t500 and did the driven diesel regulated return. I have double checked everything is plugged in. Now when I try to start it cold it will just crank. Yes I get smoke and oil pressure both places. If I give it a shot of ether it will start right up and run fine all day. What am I missing? Yes I know ether bad.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F450 - Crank But Will Not Start
i have a 99 f450 7.3 that cranks but will not start. I did an injector buzz test but it sais no communication between the computers. it has a new rebuilt engine, new ipr, icp, hpop, water pump, and both computers.
View 4 Replies