Ford 7.3L Power Stroke (1999-2003) :: High ICP - Code P1211
I had a p1211 code when I first got Torque Pro hooked up. I figured it was just because I'd done a couple WOT runs and the HPOP just can't quite keep up with the injectors. I was told this might happen when I ordered the injectors from Gear head. I also noticed that my ICP peaked at around 3600 during one of these runs. I don't have it logged, but I'm certain it was up that high.
The code hasn't returned, but I haven't been running it too hard either. I don't quite know what to make of the ICPs actually being that high. From looking at a bunch of Rich's graphs his doesn't really get past 2800 or 2900. Is this an incorrect reading? Do I need to worry about anything?
Ford 7.3L Power Stroke (1999-2003) :: Got Code P1211 - Using Dash Command?
My truck gave me the p1211 code today. I'm Trying to use dash command to get more info. What should I be monitoring and how do I do it? I'm not familiar with these apps at all?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: P1211 Code With Constant Service Engine Light
I was on the way back from the weekend trip and got a service engine soon light. I didn't notice any lack of power, rough idle or hard starting cold or hot. So we pushed on home. I checked the codes and it is the P1211.
Doing some research it seems the ICP is not as expected so I hooked up my phone with the Torque app and the IPR and ICP seem to be close to normal at idle and running. I din't see any high IPR %.
At idle the IPR was around 15.5 cold and 10.1 after a short run to the store and back when it warmed up a bit. ICP was around 690-720 cold and 470-490 when i got back.
Does that seem like normal readings? I cleared the codes and the CEL comes back on right away after starting the truck. I do have a TS performance chip that I will take out and see if that could be causing any problems. What else should I be looking into?
Ford 7.3L Power Stroke (1999-2003) :: Smoke Coming Out While Pulling / Code P1211 When Going Uphill
I have posted a pic of a smoke issue I am having while pulling.
I just pulled a 10,000 lb trailer up a few 7% grades at 8-10,000 ft and the best I could do was 40-45 mph at 6mpg. Every hill would set a P1211 and when the truck downshifted to 3rd the smoke would go away for the most part.
Truck is 100% stock and pulls the same as my F350 with 3.73 gears but smokes a lot more.
The smoke is kind of annoying and performance seems sluggish especially given the 4.88 gearing. Where to start?
Has new ipr, hpop, icp, fuel filter, air filter, fresh 5w40 mobil 1.
Ford 7.3L Power Stroke (1999-2003) :: F350 Blowing Black Smoke / Code P1211
I have a 2003 F250CC 7.3 with 200,000 miles on it. I just purchased this truck about a month ago. My question is it blows black smoke. A little at idle but mostly when you give it any pedal. I have replaced all of the injector o rings and that didn't make a difference. Then I had it tested and it failed a CCT test on #2 cylinder. I have an injector to put in it, but am curious to find out if 1 bad injector would be enough to make it smoke all the time. I keep getting P1211 ICP pressure above desired. I had a friend of mine who used to work at a ford garage take a look at it with his computer and he said that everything looks good other than the CCT test.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Code P1211 - Service Engine Light Pops Up Going Steep Hill
I have 2003 f250 7.3 automatic 181,000 miles completely stock. Never had chip,tuner or anything on it. I am second owner and got it when it had 70,000 miles on it. Ok here we go I live on top of a mountain and soon as i start up the mountain or any steep hill, or pull or tow something my service engine light pops on. First time it came on I took it to diesel shop they hooked it up to scanner and said it was code p1211 said icp sensor was bad so they put new one on. Couple days later light started popping back on so i decided to order a auto ingenuity after doing some research.
Hooked up to truck started up mountain while scanning at wot light pops on code p1211 and think it was live data I remember seeing icp pressure at 1922 and duty cycle at 63% i was trying to drive and read it at same time and my lap top went dead. What does this reading mean 1922 pressure/ at 63% cycle done little research but dont really understand. Year and half ago replaced all orings on all injectors, new rebuilt hpop pump. New ipr valve, glow plugs, past month 2 different icp sensor new,and new ipr valve new pig tails on both and light still popping on.
Ford 7.3L Power Stroke (1999-2003) :: F250 - Truck Would Die While Driving The Truck
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Exhaust Leak At Passenger Side Up-pipe To Manifold - P1211 And P1280
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Missing After Start Up - High Idle - Got Codes P1316 / P1211?
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.
Ford 7.3L Power Stroke (1999-2003) :: Truck Was Shutting Off While Driving
Last week the engine in my truck was shutting off while driving. Happened to me 3 times over the course of two days. The first couple of times, the engine was dead for 3-5 seconds and then the engine would come alive and drive normally again. The third time was about a 10 second event...same result, engine refired on it's own and drove normally. I was in motion all three times so the engine restarts all occurred before I was able to bring the truck to a complete stop.
No check engine light...(I didn't pull any codes because I didn't have my laptop with me). So, I decided to try a new CPS. I had one in my glove box since 2003 so in it went. It replaced a black CPS that I purchased from Riffraff about 100k miles ago. The new CPS seems to have done the trick. I've driven about 500 miles since the swap and the symptom has not returned. I wonder how long this one will last. It's a Ford replacement part so maybe I'll get another 100k miles...
Ford 7.3L Power Stroke (1999-2003) :: Truck Won't Run - IDM PCM Communication Code P01668
My baby won't run throwing PO1668 IDM PCM Communication Problem. It threw the CPS code first I changed the CPS and it now has the other codes. I'm stuck how do I test the idm all the fuses are good and the relay is good I believe I switched with another one... 341,000 miles I love this truck .....
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Died While Driving Almost Like Ran Out Of Fuel
I have a 2001 F350 7.3l diesel.
My truck died the other day while driving almost like he ran out of fuel. Well he had fuel so I checked the oil and it was dry. There was an ugly puddle between the intakes and a whole lot on the ground leaking out. Also the puddle looked blueish.
Put in more oil and got him home but I can't find the leak. The only thing I've noticed is that the intercooler on the cold side came off slightly. A year ago I had to go mess with the UCVH and when I put it back together I had lost a dang intercooler duct clamp and replaced it with a sturdy ring clamp. Well it wasn't sturdy enough.
How much would this leak if it came off for a little while and how serious of a problem would I have as a result? I don't have any check engine light and as long as he has oil he runs fine.
Since I have reconnected the intercooler and idle tested the truck I can't reproduce the leak. I don't believe that a huge amount of oil is running through that intercooler because the turbo is lubricated through another system I have read. So what gives?
Also I am getting weird dip stick reading. For a little while when I ran the truck today he was showing WAY over full on the dip and then down again a little bit below the operating range line. Also there are a lot of air bubbles on the dip stick when it comes up. Way more than I am used to seeing.
Also, I really like the idea of cleaning my engine off really good. It's a frigging mess now. What precautions can I take to clean it up good without making a huge mess. Can I just go the car wash that has a degreaser hose and drain and just spray it down like nothing or is it sensitive and finnicky when wet? Cleaning between the intakes seems almost impossible without getting the whole turbo system out of the way. Should I be thinking about that?
Ford 7.3L Power Stroke (1999-2003) :: Truck Stalling While Driving / Dies For A Second On Accelerating Or Cruising
Like the title says my truck has been stalling while driving. Accelerating or cruising it dies for a second, two at the most, and then just keeps chugging along again.
I thought i'd fixed the problem last year when I did injector O-rings and 50 cented my UVCH. It hadn't done it since, until two days ago. Started out with a two good solid stalls while gently accelerating up hill. I had thought maybe my fuel pickup foot had finely given up the ghost because I was below a quarter tank. But I filled her up full, and then she did it again about 50 miles of driving later.
I didn't catch the first four stalls on my torque app, because I'd just recently decided to stop logging every trip, with the thinking that it had been half a year problem free, why keep logging waiting for something that isn't going to happen. I did catch the 5th stall on the torque log. But I'm having trouble trying to figure out where it happened in a 30 min log.
First question where would yall start in tracking this thing down? Next what data actually should be logged? I think I've got some extra stuff in my logs that isn't necessary, and is maybe bogging down the system. I get one data point per second resolution on my logs. Are there ways to improve the resolution, will getting rid of some PIDs work?
Lastly I need to attack this thing smartly, without throwing time and money at unneeded parts. I had surgery and I've been out of work for 3 months and I'm looking at another 6 before I'm making money again, and there is no unemployment for the self employed. Also I only get 3-4 light weight upright hours a day to work, exceed that and I'm back on the couch battling swelling for a week.
Also is there anything I can do while driving to "flag" the stalls so I can find them more easily in the logs?
Ford 7.3L Power Stroke (1999-2003) :: Truck Is Starting Slow And Dragging As If Batteries Going Bad / Code P1247
Got two brand-new Motorcraft batteries installed about a month ago and truck has been cranking great. However, the last couple days in the mornings the truck is starting slow and dragging as if the batteries are going bad. It does crank pretty quick but just has a noticeable starter drag now. Since I have no way of diagnosing the batteries with a tester over the holidays.
What are the odds that brand new batteries are going bad? I was thinking this is a starter issue since the drag is most prominent in the morning but it does it throughout the day while I'm driving driving on each start. But it's not as bad as the first start-up.
I hooked up a scan tool (Forscan and Dash Command) and the only trouble code I received that something to do with the turbo boost pressure fault, it was a code P1247. I don't see how a turbo boost pressure fault, low pressure, could have any starting related issues but you never know. Just a note this code only came up on my FORScan Lite app but it did not come up on the dash command app so I'm not sure if it's a legitimate code.
So I'm back to a battery or starter issue. Is there a way that I can check without much equipment to detect whether not I have a starter or battery problem. I do have a battery charger but no other equipment.
Ford 7.3L Power Stroke (1999-2003) :: 2000 Truck Taking Three Cranks To Start - Code Is P1280
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Code P0264 - Unplug 8 Injector Truck Almost Dies / Plug It Up And Smooths Out
Early 99' model I picked up. Blew the oil cooler and had lot of pressure in the Degas bottle, so did head job and oil cooler and now I'm Still getting a P0264. Unplug #8 injector truck almost dies, plug it up and she smooths out...
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Truck Missing And White Smoke Coming Out - Code P1316
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 Suddenly Dies While Driving - Code P0683
I have a 2002 ford excursion. I know they have cali emissions. It runs fine then suddenly dies while driving. We've replaced the glow plug switch and relay. Neither one fixed the problem. we washed the motor a while back and it fried the programmer wiring.
View 7 RepliesFord Super Duty (1999-2016) :: F350 - Black Smoke And Low Power / Code P1211 Under Heavy Throttle
I have a 99 350 sd 7.3 low power black smoke sets a p1211 under heavy throttle. Check icp on scanner under heavy throttle falls from 1900s to mid 1700s ipr duty cycle runs about 62% wanting to know if I am looking for a hpop problem or injector issue...
View 1 Replies