Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - SES Light Came On / Truck Started Running Rough And Lose Power
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Sluggish In 1200 - 1800 RPM Range Intermittently
I am still trying to debug my 7.3 running sluggish in the 1200-1800 rpm range. The problem is intermittent. I checked the wiring harness under the valve covers to verify they are plugged in and there are no opens in the circuit. I replaced the crankshaft position sensor and the high pressure oil sensor.
This will run fine one time and a few miles down the road it will chug and smoke out the exhaust until I either get into the accelerator or back off and re press the accelerator. Again, it does it intermittently hot or cold.
I ran both a cylinder contribution test and perdels with a Snap On Verus. The cct passes everytime. The perdels have a couple of cylinders 5-6 and 8 fluctuate between 0 and 1.80% with #8 up to 2.5%.
My question is. Do the cylinders in the test correspond to the actual cylinders in the engine? Reason I am asking is the Verus does not follow the firing order on a gas engine. The cct is in order of 1-8 and I have to correlate the cct order to the firing order. Found this out the hard way when I had a bat cop on a 5.4 and replaced it only to have the same cylinder still show not firing.
I got out the graph leads and tested the cylinder and pulled the injector thinking it was bad. Everything showed good but the cct still showed it not firing. I had to unplug each coil and watch the cct to determine what the true cylinder in the test was. It turned out to mimic the firing order so I am asking out of concern that cylinder 3 in the perdels is really cylinder 3 or a different cylinder.
Btw, the perdels all show 0% if the transmission is in drive. I would have thought that a load on the engine would have showed higher perdel percentages with a load on it.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Will Die For No Reason
01 f250. Just bought from my brother. 140000 miles. Immaculate. Truck will die for no reason. Running down the highway, or sitting at a red light. Fires back up. Sometimes have to crank a few times. He has had at a mechanic and everything checks out good. Since birth its only had royal purple that he has changed every 5000 miles as well as all filters. Where do I start?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Won't Start
So I have a 2001 f250 7.3l and on my way to work yesterday while driving down a hill I switched my ts 6 switch to 140 and it immediately stalled, so I pulled over and restarted the truck and it started up fine and I drove the rest of the way to work, I go to start it after work and it won't start, it just cranks and cranks and cranks, occasionally it'll fire and I got it to start and was able to rev it for about 30 seconds but then it died, disconnect the 6 position switch from the idm and tried but still nothing.
So today I replaced the ipr valve, got everything back together still won't start maybe a little worse now, I know it's getting fuel cause there's pressure in the bowl when I try to take it off, there's a new icp valve, cps, new fuel filter and new sending unit, the hpop is topped off. Also I noticed when I went to change the ipr the wires on the plug were bare and touching so I addressed that, I don't know what else it could be?
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Just Stop Running Like Key Turned Off
My 2001 f250 7.3 was running then just shut off like I had turned the key off, While trying to start back up, the truck turns over fine but no fire. I also have no gauges, I tested both fuse boxes and the one under the hood I have power on all big fuses, including the PCM but some of the small ones I don't, No power to the PCM diode, either side, the fuse box inside the cab, I have half power, No power to the PCM fuse is their a fusible link somewhere?
I really can't see much down there. The truck did get into a accident in Oct, which created a problem with the ignition and not sure if that could be a problem? That problem is, when I turn the vehicle off, it would stay running for a few seconds. I ignored the problem cause it didn't hinder the vehicle any.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Has Always Had Difficulty Starting Cold
2001 F250 7.3l 294k miles
Ok so truck has always had difficulty starting cold since I got it about 12k miles ago. Replaced glow plugs, that made things slightly better but still no start unless temp gauge was in that first line above the C. Changed to Rotella, immediately after oil change starts better and at slightly colder temps.
Since getting the truck when you turn the ignition on you can hear a 'whistling' type noise which I believe is the fuel system pressurising. That used to last as long as the chimes did when you first turn the ignition on. More recently it lasts a lot longer.
Towed recently and had intermittent check engine light - believe this could be HPOP related, haven't checked codes yet as we're on vacation. No oil in the valley. But I do have a little oil carry over in the turbo intercooler pipes.
Truck slightly sluggish at setting off initially and then picks up reasonably well when not towing but my Dyno says I'm putting a bit more pedal to get the same performance from say two months ago
Pretty sure injectors haven't been changed since truck was new but can't be absolutely certain as there is no history. I was surmising this is probably both a HPOP and injector age issue but only from what I've found searching...
Ford 7.3L Power Stroke (1999-2003) :: Battery Light Flicker In Time With The Idle Of Truck
I bought a 7.3 f250 with 300k mi. It had a battery light on but didn't show any signs of trouble. Eventually started dropping volts a few days later and I replaced the alternator. The light is still on and flickers in time with the idle of the truck and sometimes goes out when I'm on the gas pedal. Some nights when the lights are on the voltage drops ever so slowly until its drained. Why the new alternator didn't fix the problem? NAPA's scanner says the truck has 12.4V at idle and 12.1V at idle with the lights on. Batteries are relatively new and test fine, dual Interstate Mega-tron Plus batteries-top of the line.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 Truck Losing Power / Service Engine Light Came On
Truck started losing power then service engine light came on, drove about another mile then it just stalled ( almost home lees than a 1/4 mile). Got out open hood oil everywhere on top of motor. Looked under truck and oil all over the road. Looked back where I was driving a line of oil as far an I could see. Checked oil barely any on stick. Where should I start hpop or plug?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Truck Would Die While Driving The Truck
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - O/D Light Flashes Until Shut Down?
Have no OD, when you press the OD button nothing happens and then the OD light flashes until she's shut down. On start up no flashing until OD button pressed. All other gears shift lovely. Haven't checked codes yet.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 XL - Light Burned Out At Dashboard - Replacement?
I've got a light burned out on my dashboard. No big deal (it still gets some light from an adjacent bulb) but just out of curiosity: How big a nightmare would it be to replace a lightbulb in the dash of a 2001 F-250 XL?
Do you have to pull the motor/trans and lift the cab off the frame like I've been told you need to do to replace a heater core? Local mechanics laughed at that job and told me to get some stop leak...
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Airbag Indicator Light On For Code 47
About a year ago, my airbag indicator light threw a code 47. It did this for about two days, then it stopped. Fast forward to this weekend, and it started again. From what I can tell, it is the passenger side seat belt pretensioner. It could be a coincidence, but my daughter pulled the seat recline lever without anyone being in the seat, causing it to fly forward as if James Bond was ejecting someone through the windshield. The next time I started my truck, it was throwing the code. I tried to check to see if the plug was knocked loose during the ejection sequence. I thought the connector was under the passenger seat, but I don't see any wiring (the passenger seat is manual). My next guess was behind the glove box, but I'm not sure what I'm looking for.
My truck is a 2001 F250 4x4 Lariat.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Dash Light Starting To Go Out / Bulb Replacement
I have a 2001 F250 Crew Cab with Powerstroke. The dash lights are starting to go out one at a time. How do I get to and replace the bulbs?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Just Quit While Running 70 MPH
Traveling right now. Limited access to FTE.
On the way to the airport this morning at 4:30 am, the engine simply did while running down the interstate. Absolutely no symptoms leading up to it. Turns over fast but will not start. White smoke from tall pipe while trying to start.
I unplugged the fuel bowl heater and checked the IPR tin nut and the ICP sensor connections... Nothing obvious.
Problem was CPS and the engine is now running fine again.
Ford 7.3L Power Stroke (1999-2003) :: Heater / AC Fan Running When Truck Is Turned Off
2003 CC 4x4 ... I am pretty sure I know what is going on, but I wanted to start a thread for when I confirm it. I am driving to work this AM and I hear the door ajar chime and I think to myself, uh oh...gauges all look good, there are no lights illuminated on the dash. I get to work and turn the truck off and my fan stays on. I think the ignition module is going bad. Either that, or my remote start is going on the fritz. I will update when I find out more.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Running Rough And On Less Than 8 Cylinders
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Possible To Add A/C To F250 Truck?
So long story short I have a 99 f250 xl, 7.3 130k. Overall good truck but has no options, never had AC but would like to add it. I have seen the kits on bought4less. So I'm thinking all the factory parts should be bolt on, since the holes should be all there, and since most of the wiring should be there. I just need to collect all the parts. Also one question I have is, what goes through the firewall. Is it just the lines, or how does the ac get to the vents? Dumb question but don't get that part of it.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Starts Then Dies / Cuts Out When Running
I have changed pickup filter in tank and cleaned 2 tube filters in tank i thought that would fix it.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.