Ford 7.3L Power Stroke (1999-2003) :: Hard To Start / Whitish Smoke When Cranking
This is kind of strange, I have a hard start problem, when I crank it the first time, it fires immediately, kind of like a romp, but doesn't start, then when I crank again I get a lot of whitish smoke and no start. I read to try and unplug the ICP and try it. That worked, and I had oil in the connector. I replaced the ICP, but have the same problem. I still have to unplug the ICP for the truck to start. When it does start, it runs great! No injector stiction, no smoke, no rough idle, it runs and sounds great. Why unplugging the ICP is still required to start? (Only after sitting for more than 10-12 hours).
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 - Hard To Start / Taking Lot Of Cranking
I have a 2001 F-350 7.3L Powerstroke. 48,000 miles. I've been having trouble with cold starts. So far it has always started but is taking a lot of cranking, but it hasn't gotten too cold yet so I'm worried about when it does. I ohmed out the the glow plugs and am getting close to 0 resistance. The GPR has 12.5 volts on the hot side and when the relay is closed 10.5 on the other side. Is that difference in voltage in the GPR enough to screw up the Glow Plugs heating up? If I plug it in at night it starts right up. I'm worried about when I am at work for 16 hours and don't have a place to plug it in this winter. BTW this is my first winter with the truck.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Won't Start - Battery Voltage Will Keep Falling If Cranking Continues
So when its cold and im talking below 55 degrees, and the truck hadn't been started that day, it will turn over 3 or 4 times before the voltmeter takes a dive down to 10 volts or so and doesn't start. The voltage will keep falling if cranking continues. I took the batteries out and had them tested. They are both above the rated cca. So im thinking it could be the starter windings?
I did replace an injector recently so all the cranking to get it going again may have ruined the starter? But when I hook up the battery charger and jump the truck it starts. And after it has been started it will continue to start easily the rest of the day.
Ford 7.3L Power Stroke (1999-2003) :: No Start - IPR Goes Straight To 98.6% While Cranking
This morning I went to start her up, and she fired right up and I let her warm up until oil temp got to 100F, when I realized that I wasn't leaving right away so I shut it down and came back about an hour later. Oil temp now at 78F, but she wouldn't start. Have Torque Pro running, and the IPR is going straight to 98.6% every time while cranking, sits at 14.7% with KOEO.
Truck's been running fine, recent oil/filter change (T6 10-40W), cleaned & re-installed CAC tubes/boots for leaks. All else seems good. Pulling the ICP sensor shows HPOP going to 2800psi, with IPR @ 30%, still no start and not even a cough.
The IPR is original, rebuilt once several years ago.
Ford 7.3L Power Stroke (1999-2003) :: Died And Won't Start / RPMs Only Like 200 When Cranking
Was driving to work about 4 miles into my travel rolled around corned and she died..... tow bill and cps she fired rite up. Ran at idle in drive way because I was a little leary for about an hour left drive way went 2 miles went to pull in to store died again. Another tow bill and 2 more cps still won't start rpm is only like 200 when cranking but sounds like a lot more. The wts light works, batteries are pretty new, cps in new...
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Cranking For A Bit Of Time And Refuses To Start
I have a 1999 f250 7.3 psd. it cranks and will not start, it use to crank for a bit of time and then start and now it refuses to start. If I leave the key in start position for like 30 seconds it use start and now it wont. I am thinking it is something with the glow plugs?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Harder To Start After Long Cranking
Background on the vehicle, Last week installed Swamps 200cc/30% injectors with a 38r. Had swamps reburn my chip for the new upgrades.
But heres the problem i noticed starting the truck was a little harder ( longer cranking ) till it would start never thought of anything since i read air gets in and can cause it but then yesterday and today its taken 30 minutes to start the truck since i have to do a trial and error.
The truck just seems like the batteries are being drained or something along those lines. i also noticed my gauges keep resetting back to blue( default color). Today I plugged a battery charger up all good voltage i charged them so both read 14v and still no start. So a couple of attempts at starting with chip in and ICP on nothing
I unhook the chip and ICP get a half start then eventually it starts. After then i can hook it all back up and it starts good for the rest of the day but for what ever reason after it sits all night it doesn't want to start up right away. I'd like to figure it out today since id rather not wake up at 4am and attempt to do this all before work each day.
I noticed that my gauges would reset to the default color after each turn off. So i unscrewed my ECU and then redid that to make sure its tight. along with making sure the chip is seated properly. after that it stopped resting my gauges. Whether that's the issue or not i cant say but ive been checking my HPOP oil level since i stopped driving it around 1400. and hasn't changed oil levels are good. I plan on starting it before I go to bed around 2200-2300 just to check and see what happens.
Ford 7.3L Power Stroke (1999-2003) :: E99 Won't Start - White Smoke / RPMs Move While Cranking
Fine one day, no start the next. Been skimming over the 7.3 no start thread, so w got some ammo for him to check. White smoke while cranking, rpms move while cranking. Nothing to read codes or other sensors YET. Tried the unplug ICP and it "wanted" to fire. So, I have him my spare IPR to try. I'm sure he checked the fuses but will confirm via text...
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F550 Taking 4 Seconds Of Cranking To Start Consistently Hot Or Cold
I have now replaced hpop, injectors, cups, gpr, batteries, uvch on both sides, icp and ipr on my 2002 F550 and it still has a long crank to start.
It has been driven about 1,000 miles since then and no change. I have no codes except buzz test produced a high to low 1272 1274 1276 1278 one time. Cannot get that to happen again.
It is taking 4 seconds of cranking to start consistently hot or cold. It always starts but cranks for what seems like too long compared to my other 7.3s. I have included a screenshot of the data and am curious on what everyone's thoughts are as I am out of things to look at!
Ford 7.3L Power Stroke (1999-2003) :: Hard Start Getting Harder
My e99 f250 has been getting harder and harder to start over the last year.
I think one of my batteries is dying or dead but it still cranks fast while it does.
For instance when I tried starting today it seemed to crank just like normal but their was some relay clicking inside the cab that was abnormal.
My understanding is aside from cranking no power is required to start the motor? what if the dead battery is taking some cranking amps from the good battery preventing the computer from getting juice?
would the truck throw a code if it was a glow plug?
Ford 7.3L Power Stroke (1999-2003) :: Hard Shifts - Truck Will Take Two Tries To Start?
The first has I replaced my tranny with a stock 4r100 tranny and torque that only has 75k on it. The guy was doing a 6-speed swap. After I had the tranny and torque converter and a new tranny cooler installed, the tranny shifts real hard. I think it may be from my DP Tuner. Even on my economy tune driving it very easy sometimes, it jolts into gear pretty good.
I was wondering if I could just get a shift kit to maybe correct that and if so if I would have to drop the tranny to install the shift kit. I saw a bully dog kit for like 75 bucks, however, I don't really have the money to have the truck in a shop and I would really like to not drop the tranny and not lose all my tranny fluid if possible (very expensive).
Also my other issue, the truck in warm or cold weather is very hard to start. Half of the time it takes two tries to start it. It will crank and crank and no go. Then the second try it fires right up. It has two new batteries, where do I start? Is it possible that the starter is just getting old or is it fuel or oil pressure related possibly?
Ford 7.3L Power Stroke (1999-2003) :: Hard To Start When Longer It Sits
2001 F 350 7.3 183,000 miles.. The problem is the longer it sits the harder it starts.. when it does start it runs VERY ruff!!! it takes 10 min or so to run on all cylinders.... This is my first diesel..
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Hard To Start Cold - No Codes
My truck is hard to start when cold and I suspect glow plugs. But it is not showing any codes? If it is a glow plug or glow plug relay at fault , should it throw a code?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Hard Time To Start Intermittently
Just got myself a gently used Econoline E-350 7.3 Diesel and was loving it when she ran:
E-350 7.3 Diesel
Recently I have been having some charging issues. It started with it intermittently having a hard time to start, especially when it was warm. I carried a jump box with me and that always seemed to work. Then I noticed the voltmeter on the dash dropping. It went down to the 8 and I was like something is wrong.
Checked the battery voltage, it was at 9.6v. OK, maybe alternator isn't charging. Advance Auto tested the alternator, said it was bad. I replaced alternator. No difference. I pulled the battery and ran it on a conditioner to bring it up to proper voltage. It's now at 12.6v resting. Starts the van no problem. When running though the voltage doesn't increase to 13-14 volts like it should though telling me the alternator isn't doing it's job. Increasing engine RPM actually decreases voltage? Checked all the obvious things like bad grounds but everything seemed clean.
The only thing that was fishy was when I pulled the three way plug from the alternator, one of the pins had corrosion on it. I cleaned it up before installing the new alternator. I didn't do a diode test on the new alternator because I figured it was new, but hey maybe I got a lemon?
Anyway I'm going crazy trying to figure out where the problem is. All fuses are ok. Is there an external regulator or something I should be on the lookout for? Is there anything else that could be causing a non charging issue? The battery was manufactured in 2014 so it's relatively new.
And on a random note my ABS light is now on?
Ford 7.3L Power Stroke (1999-2003) :: F250 Hard To Start / Rough Idle?
My 2003 7.3 f250 has trouble starting whenever the temperature is less than 65 degrees. If it is less than 50 degrees I have to plug it in for it to start. Once it starts it runs rough. I let it warm up and it still runs rough. Once I start down the road I'll get on it a bit and it takes off like something lets loose. It then runs geat for the rest of the day but does seem to still crank a little more than it should when I restart it through out the day.
The pickup has 152000k
List of repairs I have done to the truck:
-new gpr
-new glow plugs
-new uvch both sides
-new valve cover gaskets
-new blue cps
-new fuel filter
-new batteries everstart maxx 65n
The truck has an afe air intake, straight exhaust, and a super chips tuner set on mileage saving. It blows white smoke when first started but clears up pretty quick.
Ford 7.3L Power Stroke (1999-2003) :: Black Smoke At Start / Hard To Turn Over
So I've been having issues with starting my truck lately. It was really hard to turn over, would start really hard when it did and would blow some black smoke. Turns out my starter was bad so I replaced it with a DB Electric high torque starter. Now it starts up great... for the most part.
I'm still having some black smoke when it's a cold start and/or I have the key set to "On" to warm the glow plugs for a few seconds. It's almost like the starter is turning over the engine, but for the first few turns it sounds empty or hollow (at least that's the best way I can describe it). After the first turns it will sound normal how it's supposed to and will fire up shortly after but with some black smoke.
If my car is already warm it cranks right up without any smoke unless I have the key set to "On" for a few seconds to warm the glow plugs like I said earlier. Pretty much if I warm the glow plugs it makes it harder to start up for some odd reason.
What might cause this or how to fix it? Maybe some of my glow plugs are going bad, or possibly my IDM? I used to have the P1670 code by itself, however, that went away when I replaced the starter. I also just replaced my camshaft position sensor just to be sure it wasn't going bad. I've also been having some boost pressure leaks if that's relevant at all.
Ford 7.3L Power Stroke (1999-2003) :: Hard Start When Cold / White Smoke
When it is cold out side like 20 degrees I'm having problems starting my 2000 7.3 I'm cycling it about 5 times and misses smokes white for a bit then stays running I was thinking of changing out the fuel filter. What it could be?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Getting Hard To Start / Code P1670
But it starts. '99 F250 PS. Had code P1670, cleared it. No other codes. Started truck back up and ran KOER test with AE(which I'm not very good with). The code did not come back. It is hard to start plugged in cold or warmed up. I have WTS light and it goes out(glow plugs are original). RPMs are slow to come up (almost starts before it kicks in). Doesn't matter if fuel tank is full or not. Oil level is fine. Batteries are charged and check good. Starter checks out ok. Buzz test was ok. Now when I run KOER do I need to do anything other than hitting the initiate button?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Intermittent Hard / No Start Now Crank But Not Firing Up
My wife has been telling me our '01 E-350 (Econoline) with 7.3 is taking several attempts to start in the mornings, like it's not even trying to fire. It will crank like wild but no fire and then it will fire usually and sometimes run a little rough but no always.
Tonight she called me from across town and it won't start at all, cranks like wild but won't start, chug or anything.
The WTS light is working fine, the truck runs great and idles smooth all other times, just been giving grief when starting in the mornings (warm outside 70 degree plus ambient temp). I haven't had the truck do it to me but she has explained it well enough.
I do get a SES light for overboost when I run it hard (PHP tuned) but it always goes away and hasn't caused any issues. Could this be the ICP acting like this? If so, is it true that I can just unplug it and the truck will start by using default pressure?