Ford 6.0L Power Stroke Diesel :: Shift Lever Sticks In Park
A few months ago I couldn't get the shift lever out of park without trying multiple times. Then it was okay for about 5 months now it is back and worse. It is not bound up because of parking on a hill or anything like that and I press very hard on the brake pedal. It take s multiple times to get it out of park trying turning the key on and off and so on. The truck only has 86,000 miles on it and the transmission has always worked perfectly.
View 6 RepliesFord 6.7L Power Stroke Diesel :: 2011 - Hard Shift From Park To Drive Or Reverse
2011, 69,000 miles. My truck is experiencing very hard shifts from park to drive or park to reverse after a cold soak. It goes away once warmed up. I can't find any excessive driveline play and my transmission fluid level appears fine and in good condition.
The last repair done on my truck was around 7,000 miles ago and it was for a transmission fluid leak around the bell housing. They just replaced the seal between the torque converter and transmission.
Ford Escape / Hybrid :: 2009 - Shifter Lever Stuck / Unable To Shift Out Of Park Without Using Manual Override
My 2009 Ford Escape shift lever is stuck, not allowing me to shift out of park without using the manual override. However, when I slam my foot to the brake (rather than simply stepping on the brake), the brake switch relay, etc. all engage and I am able to shift out of park. Is this a brake switch relay problem, or is it possible that it has to do with the age of my brakes, etc?
View 3 RepliesFord 6.7L Power Stroke Diesel :: Bouncing When Downshifting From 6th To 5th At 60 MPH
Got a 2011 F350 Crew LB. When I'm pulling a mild grade, put my foot in it and down shift at about 60mph, I will get a real good rear-end bounce going on. It sounds real similar to the 45-50mph bounce in that if I slow down or power through it the bounce will go away. If I sit there at around 55-62 it will develop a real good hop (standing wave like). I've never had the 45-50mph bounce problem, BTW.
It just started happening in the past few months. The truck has an Icon leveling kit with bilstien shocks and slightly taller tires. The leveling kit and tires have been on there for a couple of years. Just replaced a leaking rear shock thinking it was the cause, but no happiness.
Ford 6.7L Power Stroke Diesel :: Transmission Downshifting Hard Into 5th
I tow a car hauler that is about 8000 lbs. On my last trip occasionally when the truck would downshift into 5th under a load, it would bang in there pretty hard. Not a smooth transition, not every time just some times. Just wondering it that was normal or the start of a potential issue.
View 6 RepliesFord 6.7L Power Stroke Diesel :: Motor Was Knocking Tapping - Power Loss Then Just Shut Off
Not sure, it doesn't seem to me the dreaded fuel pump problem. Was driving on highway pulling my 5th wheel after going though the toll both it never went out of 3rd gear and motor started taping pretty bad, turned tow haul off and it shifted up. All along never seemed to lose power, as I was looking to pulled off high way and into A park in lot it started losing power then just shut off. All along this 2min ordeal the motor was knocking/taping. Seems to me like the motor blew.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Loud Clunk / Bang When Downshifting Under Load
38k and 15 months old. Runs fine except...
Can be in cruise or not, tow/haul or not, but need to be pulling a decent hill with 7k+ trailer. Running level with air bags. Regardless of speed, cruising at 50, 58, or 65, beginning incline and turbo boost builds normally to maintain speed to the point when it needs to downshift. BAM!!, not just a clunk, 90% of the time- scares the hell out of me. I can make it do it on an incline empty, but it it difficult. If because initial speed is 50ish, a second downshift to 4th may be needed. A bang only 50% of the time.
No codes.
Regardless of the degree incline, (toughest in the NC/KY areas is 6-7% grade, can avoid harsh shift by backing off on throttle and manually downshifting to 5th or 4th, depending upon speed.
Can "make" it do it on level terrain with 7k trailer if I slowly back off throttle and slow from 65 to 50 or so and punch it, but not too hard. Too hard and it goes to 4th, usually with just a modest clunk. Just right and I get 5th with a loud, and I mean loud BAM. Even the tech was impressed.
Afraid to hook up my 17k 5er and take off for the next 3 months, which is the reason I bought the truck to replace my 11...
Carrier bearing has grease coming out of it (400k on various duallies and never seen this), but dealer says not an issue.
Ford told dealer that it had no idea, and advised tech to do a lot of pin point electrical testing and everything checks out. Next stop is the inner workings of transmission.
I have been without it and work for 3 days because of backlog. Running two day load tomorrow, then back in for tranny work.
Ford 6.0L Power Stroke Diesel :: 2006 F350 - Clunking When Go From Drive To Reverse And Now With Drive Too
So I have a 06 350 and I'm getting clunking from drive to reverse and now with drive too, I know my rear diff is on it's last days but I am wondering if that could cause the clunking and now my truck around 90km shakes likes crazy and same thing wana know if that's the diff. And if I was to fix diff myself would it not just be easier for me to just swap axles if I wanted to be cheap??
View 12 RepliesCamry :: 2011 - Shift Lever Harder To Move Than Normal And Would Not Go Into Drive
I had something unusual happen recently... I backed out the driveway and went to put the car in drive and found the shift lever harder to move than normal and it wouldn't go into drive. It would go into park and reverse easily enough. After some manipulation it went into drive and ran with no problems to my destination. At first, I thought something fell down into the mechanism and was causing it to bind. AND of course, when I showed it to a pal, I could not recreate the issue. The next morning it worked fine, but it happened again later in the day, but it took much longer to get it into drive.
On the way home, the check engine and traction control lights both came on. I dropped it off at my mechanics and he diagnosed error code C1201 P0705 and claims that the remote starter (shop installed after market) is interfering with the transmission control module. I contacted the installer of the starter and he says it is not possible, but I know something is wrong... Now, I can't get it to act up and the idiot lights are gone. I need to rely on my vehicle and can't afford to be stranded somewhere. I feel it would be pointless to take the car to the installer, since the warning lights are gone and there are no shifting issues now.
Ford 6.7L Power Stroke Diesel :: Engine Made A Tapping Sound For Few Seconds Then Shut Off After Loud Pop
The EMS service in the county next to ours lost one of it's new trucks for a few days on Tuesday. While going on a call, the engine made a tapping sound for only a few seconds, then a loud pop and shut off. Ford dealer went and picked it up and took it in for evaluation. VERDICT: Broken rod and cracked block. I have to say, this is the first I've heard of a 6.7L having a problem like this in our area.
Ford was really interested in this engine, as a new one is already on the way and the old one is to be shipped back for complete breakdown. So far, the Director and County Manager have been impressed with Ford's response to this problem. Dealer has told them the truck should be ready by the middle to end of next week. If I hear anything else, I will let you know. Any engine can break at any time, I'm just glad they are moving quickly to rectify the situation.
Ford 6.0L Power Stroke Diesel :: Torque Shift Trans / 4 - 5 Gear Shift Under Hard Acceleration
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 RepliesLincoln - Towncar :: 2001 - Intermittent Vibration When Move The Gear Shift Lever To D For Drive
I have a 2001 Lincoln Town Car that has an intermittent vibration that can be felt when seating in the car and you move the gear shift lever to D for drive. The car has 141,000 miles. It is an automatic transmission. The vibration cannot be felt when touching the steering wheel. What could be causing the vibration?
View 3 RepliesFord 6.0L Power Stroke Diesel :: Location Of Manual 4wd Shifter Mounts To Transmission?
I cannot locate a picture of where the manual 4wd shifter mounts up to the transmission.
I am finishing up 4wd'ing my F550, but am not exactly sure how the shifter bolts up. Can someone take their boot and bezel off and take a couple photos of how the shifter mounts to the 5R100W by any chanc?
Ford 6.7L Power Stroke Diesel :: Truck Makes A Metal On Metal Screech When Downshifting From 5th To 4th And 4th To 3rd Occasionally
I've had transmission issues with my truck that the dealers can't seem to duplicate. The truck makes a metal on metal screech when downshifting from 5th to 4th and 4th to 3rd on occasion. The two dealers claim they cannot duplicate the issue and there's no CEL so there's nothing they can do. The shifting is also super slow between gears and regularly hangs in 4th until I let off the pedal for a good two or three seconds. All gear changes are slow.
Now the truck is exhibiting a new issue. When coming to a stop, a second after stopping the truck faintly jerks forward. Almost like the torque converter is not fully unlocked.
Elantra MD (2010-15) :: Manual Transmission Loose - Gears Make Noise As Shift From Coast To Drive
Ok so my transmission feels loose, too much play between the coast and drive side of the gears. Makes enough noise now that my wife complained about it so I'm looking into taking it to the dealer. I pretty much expect them to pass this off and do nothing, but its getting worse especially in the last couple of months.
Noticed a lot of play in there gearbox? Can you hear the gears make noise as they shift from coast to drive side?
Ford 6.0L Power Stroke Diesel :: No Boost - Won't Shift Properly?
Ok so I just put an egr delete and a new oil cooler in the truck. Everything went pretty well but when I was going for a test drive I'm not building any boost. I can here the turbo whistle like always but there no power and none of my gauges register boost. Also, the transmission is shifting funny I don't know how else to explain it but just not right. Now I don't see/smell any exhaust leaks and can't hear anything too wierd in that department. I checked the intake and the intercooler tubes I think their called and all good there. However, I did break my map sensor post off my intake during the install . So my map tube was just open to the atmosphere I didn't plug it or anything. Could that be the cause of my woes? Is there any thing I can do to alleviate the issues I'm having with the map? Can I just plug it until I fix it? And is there anything else to check on my turbo?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Slow Shift Between 5th To 6th When Cold
Situation is I have 2016 F350 that when cold, seems to have shift problems between 5th and 6th gear, where the engine revs between the gear shift under light acceleration. Once warmed up, doesn't seem to do it, 4th to 5th might be a little slow or maybe just my imagination.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Started To Take Longer To Up Shift
So we have a van with the 6.0. It has a little over 100,000 miles. It has started to take longer to up shift. The dealer ( I know. but I know my service guy and he has done well in the past ) says we need to do injectors and fuel regulator plus a host of small parts to do the job. about 8 grand or so of work. Everything on the trans checks out and is supposed to be in perfect order. Truck goes well once up to speed but its getting the is the problem. So its parked so we don,t melt an injector.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 4WD Will Not Shift On The Fly
I have 2005 f350 will not shift on the fly. With a vacuum pump it will hold vacuum at both hubs but will not lock up. The seals should be good.
View 11 Replies