Ford 6.7L Power Stroke Diesel :: Transmission Clank / Sometimes Downshift Hard
I have an 2011 6.7 that has a h&s tuner. Lately my transmission seems to be confused about what gear it should be in when I'm driving about 45mph. It will sometime downshift hard. I have a early build 2011 and heard that it could be a solenoid problem with the transmission.
View 8 RepliesFord 6.7L Power Stroke Diesel :: Transmission Clank - Downshift Hard - Solenoid?
I have an 2011 6.7 that has a h&s tuner. Lately my transmission seems to be confused about what gear it should be in when I'm driving about 45mph. It will sometime downshift hard. I have a early build 2011 and heard that it could be a solenoid problem with the transmission.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Transmission Slammed Hard Into First Gear And Sometimes Will Not Upshift
Everything was fine, running PHP 200X tune, switched to PHP 65 tow and took the 5er toy hauler on vacation last month. Pulled a lot of mountains,etc. While camping, took the truck unloaded to get fuel. Engaged tow/haul going down a mountain to utilize engine braking and the tunes "exhaust brake" and the trans slammed HARD into first gear. This happened twice. I refrained from using tow/haul. Heading home 450 miles with the 5er, I utilized tow/haul again (had it on the whole time, just like on the way down) and the truck and trans were flawless. Get home, switch back to 200X, and I'd say within a week or so, began having trans issues. Loaded stock tune, reset KAM with SCT, disconnected batteries with headlight switch on for a couple days, reloaded 200X and drove it for a couple days. No change.
It felt like the trans was slipping, not "going" like it should when on the throttle, and would sometimes not want to upshift. It would just act "weird". This would usually occur under 40 - 70% throttle (I rarely ever get on it more than that), but sometimes less. Never got any check engine light or tow/haul flashing.
So today I finally did what I should have weeks ago, took off work and ran the truck to a shop.
- First the tech hooked it up to the scanner. No codes.
- Test drove it. He said it drove fine for him. It was fine for me as well, driving it from my house to the shop (I didn't "get on" the throttle though).
- He monitored the voltage from the trans temp sensor. He said the voltage was fine, didn't spike or do anything crazy. He didn't seem 100% positive on this but, said it starts out at 5V cold and voltage should drop as the temp increases, which it did. However, the temp started out at 300 and then dropped to 200 as he was driving. #1 the temp isn't (shouldn't be) that high, and #2 it should increase while driving not drop. The temp shown on my Torque Pro app hit 149 on the way to the shop and 168 on the way home (90 degrees outside). So he seemed to think there was something screwy there.
- While driving it, his scanner showed a trans overheat (over temp/high temp, whatever) code, but no check engine light or tow/haul flash.
- Drove it home. Trans was fine until I got on it a bit and then it acted funny again. But just driving normal with light throttle it is fine.
* Thinking about trying a new temp sensor.
* Could it be in limp mode which is why it feels like it is slipping, i.e. doesn't have the normal power I'm used to?
* When the tow/haul light flashes, is it the tow/haul light on the instrument cluster? That's the only thing that lights up when I'm in T/H. Where you push the button never lights up. Assumed it was just white lettering and not a light.
Ford 6.7L Power Stroke Diesel :: Automatic Transmission Hard Shift Second Gear
Well I've been towing for almost 150,000 miles with a 2012 6.7 Lariat 4 wheel drive. Things have been going pretty well with the truck. I noticed some sluggish and indecisive type shifts early on but now I'm worried. I depend on this truck for pulling a horse trailer all over the country and Canada. Just recently I've been getting a hard shift or a thump or a clunk when shifting up or down in to second gear. I'm at about 152,000 miles and did a hot flush with LV ATF at about 148,000 miles. Should I worry or keep running?
I have a 97' PSD I'm thinking of giving a nice paint job and a flat bed but am reluctant to do so due to financial concerns and the fact that some folks may not want to see me pull up in an old truck no matter how nice it looks. My tranny temps have been stating under 200F and I really keep an eye on the temps when running up and down the hills while towing. The trailer is a 35' Gooseneck with a max GVRW or 14,000 pounds. Should I wait for the tranny to grenade and then drop in a built tranny and if so who's building these tranny's stronger than stock? Long time no see but this site has always been my go to for all my Ford truck questions, upgrades, etc.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - Transmission Shifts Hard To A Lower Gear
I currently have a 2006 F-250 6.0 with 187,XXX.
My problem that i am having is that the transmission recently within a couple weeks started acting weird about the same time 3 of my fuel injectors started failing. When i start up the truck and put it into drive it takes about 3-5 seconds to shift. Once it's in drive it runs pretty well but it will start shifting out of normal when i go to accelerate. Also when i go to slow down sometime the transmission shifts hard to a lower gear. I also have a video of the sound that it had started to make since its hard to describe.
Here are attached videos and photos. I want to hopefully fix the problems myself so i can learn more about my truck. I am going to handle the fuel injectors here soon since 2 are failing and ones about to these have been causing the truck to shudder at around 47-53 mph but after that its fine.
The transmission is stocked and never been altered, i do admit for 3-4 years I have changed the fluids or filters.
The truck is bullet proofed, sct tuner, upgraded turbo from stock, 4" exhaust, head studs and new everything when the engine was rebuilt and bulletproofed.
I plan on going to ford tmw to have them figure out the problem and hopefully its just solenoids so i can fix it myself. I have a link posted also where you can hear the noise it has been making when in R P and when shifting going down the road and it is a automatic.
YouTube.....
Ford 6.7L Power Stroke Diesel :: 6r140 - Transmission Slams Hard Into Reverse / Shifting From 1 To 3 Is Awful
I'm having problems with my 6r140 in my 2011, the truck is an early build around 8/2010 I believe.
After cold soak when shifting into reverse after allowing engine to warm a bit the transmission almost always slams hard into reverse.
After that shifting from 1-3 is awful, the transmission will try to go into 3rd but downshift to 1st then fail to go back into 3rd multiple times. This situation is extremely dangerous when trying to pull into traffic.
Oh and once the transmission gets into 3rd it will skip 4th and go right into 5th. There is only 94k miles on this transmission/truck.
I just bought this truck about a month ago, does this sound like an issue with the solenoids in the valve body?
I'm very mechanically inclined and can swap them if need be but now we're talking few hundred in solenoids and then getting the trucks pcm flashed right?
Also fluid has been changed and I used mercon lv.
Ford 6.7L Power Stroke Diesel :: Bouncing When Downshifting From 6th To 5th At 60 MPH
Got a 2011 F350 Crew LB. When I'm pulling a mild grade, put my foot in it and down shift at about 60mph, I will get a real good rear-end bounce going on. It sounds real similar to the 45-50mph bounce in that if I slow down or power through it the bounce will go away. If I sit there at around 55-62 it will develop a real good hop (standing wave like). I've never had the 45-50mph bounce problem, BTW.
It just started happening in the past few months. The truck has an Icon leveling kit with bilstien shocks and slightly taller tires. The leveling kit and tires have been on there for a couple of years. Just replaced a leaking rear shock thinking it was the cause, but no happiness.
Ford 6.0L Power Stroke Diesel :: Transmission Engages Hard On Reverse / Vibration And Some Knocking Sounds On Takeoff
05 F-350 6L .. Automatic Transmission
When I got the truck I noticed it would slam hard into reverse. Ever since it is taking longer to engage reverse gear and now I have to rev it to 1000 rpms for it to engage with a hard SLAM.
I also noticed that if I do a fast take off, there is a knocking sound coming from drive shaft/differential area (like knock knock knock knock knock then goes away). Then a slight vibration ending at around 30 kph (~20 MPH). There is also some oil leaking from the transmission. I added some mercon sp yesterday - it was a bit low.
My guess for the knocking and vibration is the center support bearings and U-joints. Transmission??? One thing I know I am going to be banging away at that shaft but the transmission problem really scares me.
Ford 6.7L Power Stroke Diesel :: Loud Clunk / Bang When Downshifting Under Load
38k and 15 months old. Runs fine except...
Can be in cruise or not, tow/haul or not, but need to be pulling a decent hill with 7k+ trailer. Running level with air bags. Regardless of speed, cruising at 50, 58, or 65, beginning incline and turbo boost builds normally to maintain speed to the point when it needs to downshift. BAM!!, not just a clunk, 90% of the time- scares the hell out of me. I can make it do it on an incline empty, but it it difficult. If because initial speed is 50ish, a second downshift to 4th may be needed. A bang only 50% of the time.
No codes.
Regardless of the degree incline, (toughest in the NC/KY areas is 6-7% grade, can avoid harsh shift by backing off on throttle and manually downshifting to 5th or 4th, depending upon speed.
Can "make" it do it on level terrain with 7k trailer if I slowly back off throttle and slow from 65 to 50 or so and punch it, but not too hard. Too hard and it goes to 4th, usually with just a modest clunk. Just right and I get 5th with a loud, and I mean loud BAM. Even the tech was impressed.
Afraid to hook up my 17k 5er and take off for the next 3 months, which is the reason I bought the truck to replace my 11...
Carrier bearing has grease coming out of it (400k on various duallies and never seen this), but dealer says not an issue.
Ford told dealer that it had no idea, and advised tech to do a lot of pin point electrical testing and everything checks out. Next stop is the inner workings of transmission.
I have been without it and work for 3 days because of backlog. Running two day load tomorrow, then back in for tranny work.
Ford 6.7L Power Stroke Diesel :: Manual Downshifting In Drive D By Tapping On Shift Lever
I just noticed I could manually down shift transmission in D drive by tapping - on shift lever. I thought this was only possible in M manual mode.
View 3 RepliesFord 6.7L Power Stroke Diesel :: Truck Makes A Metal On Metal Screech When Downshifting From 5th To 4th And 4th To 3rd Occasionally
I've had transmission issues with my truck that the dealers can't seem to duplicate. The truck makes a metal on metal screech when downshifting from 5th to 4th and 4th to 3rd on occasion. The two dealers claim they cannot duplicate the issue and there's no CEL so there's nothing they can do. The shifting is also super slow between gears and regularly hangs in 4th until I let off the pedal for a good two or three seconds. All gear changes are slow.
Now the truck is exhibiting a new issue. When coming to a stop, a second after stopping the truck faintly jerks forward. Almost like the torque converter is not fully unlocked.
Ford 6.7L Power Stroke Diesel :: When Engage Low Range In The Diesel / Transmission Starts In 2nd Gear
Well, last night I took my F-350 up a wheeling trail. I'd been up quite a few times in my old Rover, so I knew I could go a ways in without damage. Just uphill, muddy, and ruts / rock steps.
One thing I notice is that when you engage low range in the diesel, the transmission starts in 2nd gear. My previous gas Super Duties always started in 1st. I'm assuming this is to protect the transfer case from torque overload. Also, the throttle response seems to change when low is engaged (the pedal becomes less responsive, which is nice).
I've had the gas Super Duties off road before, and all of mine have had the locking rear diff. The diesel lugged along perfectly. My biggest fear was crunching the DPF / SCR / DOC canister on a rock step. In that respect, I'd rather wheel a gas. The manual shift function makes a lot of sense in low range - you can force a start in 1st, 2nd, or 3rd. And prevent meaningless up / down shifts since the grade can change quickly.
These trucks' biggest hindrance is their size. However, if you have the trail room, they are actually excellent off road. Many people look at a Super Duty and see a vehicle good only for pulling or hauling. Not so, these trucks are as good as a Jeep off road, again with trail room being the only concern. The locking rear diff was never really needed, but I engaged and disengaged a few times to keep the mechanism free. I really love this feature.
One thing that happens frequently for me in north-east wheeling is water crossings. Could be a simple brook but mostly it is mud holes encountered on tight trails. In some cases these are only a foot or so deep; in other cases they are 4 feet deep. Ford states to "try" to keep the water below the level of the hubs, which amounts to about 15". Aside from possible front axle contamination, my biggest concern would be the electronics on the diesel which are mounted to the frame or floor pan (transmission module, NOx module, etc.) The gas Super Duties don't have these concerns. In the old days, as long as a diesel had air, the engine would run under water. This engine requires electronic control of many things, including the injectors...so it won't. There are also some axle / transmission breathers which run about floor pan high to be concerned about, but these can be easily extended.
Maybe it's due to the twisty frame which GM loves to insult Ford about, but these trucks have excellent wheel articulation. I'd be surprised if a coil sprung power wagon flexed more, at least in the rear. I'm impressed.
Finally, the traction control. I experimented a bit on a slippery rock step. This was the only step which required the rear locker - sort of. The front wheels climbed the step, but the back flexed to the point of one rear wheel basically almost off the ground and severely unloaded. With 4x4 Low engaged, and traction control "off" as much as Ford will allow, the truck could not pull itself up. Turning traction control on allowed the truck to very nearly pull itself up. A little more throttle / finesse probably would have gotten the truck over, but lots of ETC operation glazes the brakes and spews brake dust everywhere. Being able to start in a higher gear manually really adjusts the torque control. Locking the rear end and the loaded wheel bit right in and she went up and over.
When doing some off-road driving, the "off-road" screen for those of you with the LCD message center is kind of fun and informative to watch. It's nice to see how far your wheels are turned left or right when spinning in ruts or what crazy angle your truck is on. Howie Long could probably document the exact up / down / left / right slope angle a Super Duty needs to be on in order for the tailgate not to open. I never had an reason to open the tailgate while in these crazy angles, of course.
Overall, very impressed. It's not as good as my old Range Rover, but I would say more talented off road than ALL other Ford vehicles except the Raptor.
Ford 6.7L Power Stroke Diesel :: 2012 F250 Diesel - Transmission Noise When Shifts Into 5th Gear?
When the truck shifts into 5th gear i instantly feel a constant vibration and noise until it shifts to 6th gear. This happens nearly every time while driving at 40mph. Rpm range 1200 - 2000. I bought the truck new on June 30th and noticed the problem on my way to work on Monday July 2nd. Took it to the dealer on July 5th and the tech said it was the torque converter slipping. I drove it home because they didn't have time to work on it. Took it back on July 12th and the dealer has had it since (currently 30 days) They originally told me it was not the engine or transmission and it was an exhaust problem. Last week they said it was the motor mounts and said they would be done.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Random Hard Starts - No Power At Speed?
I have an 03 Excursion with 220,000 on the clock. Started getting harder starts randomly about a month ago, maybe a little more, pulled codes got p2290. Reset everything, changed the oil, oil filter, both fuel filters, eventually the ICP sensor itself and rebuilt the IPR with new screen kit and rings. Hard start went away for about a week but ICP pressure was dropping drastically during hard throttle or even trying to go up a good sized hill. I had a bypass oil filtration kit on and noticed that the connection on top of the oil filter housing was weeping at idle and leaking enough at throttle to possibly cause an issue. Replaced with new OEM filter cap and fill cap, and ended up with a no start and low ICP pressure.
Got it started today after a long crank (15+ seconds), ICP and IPR at idle both warm and cold are mid 600's and low 20's (I can get actuals if needed). After reaching operating temp starts fine after shut off (both immediate and after sitting for 20 minutes). I picked up a selection of parts and tools including an ICP air test tool. Also grabbed a hpop gasket kit and the updated O-rings for the whole system. Live scanning wise I have an Edge CTS and also an SCT x4 that I can use.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Hard / No Start - Low Power
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
Ford 6.0L Power Stroke Diesel :: Truck Hard To Start / No Power At All
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 V8 - Hard Start / Rough Idle / Shaking - No Power When Cold
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
Ford 6.0L Power Stroke Diesel :: Self Shutdown Now Very Hard To Turn Over
Truck was running fine. Stopped and got fuel. Then crank truck and after about 15 secs it shut itself off. Now it WILL turn over but it is very slow and sounds "tight". 2004 f350 6.0 4x4 auto. I'm leaning towards torque converter.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Truck Pulls Really Hard To The Right If Going Over 40 MPH
If I am going over 40 mph and I have to brake hard my truck pulls really hard to the right. I mean so hard it will take me off the road. My truck is a 2004 f250 with 147,000 miles.
In the last six months I have replaced both hubs, rotors and brakes. I really drive like an old man so I don't know how long I have had this issue. Just someone pulled in front of me on the freeway and I had to brake hard and I found this out.
I have checked both front capilers and brake lines and those are fine. I have brand new tires on it. I really have no clue what is going on. I have pulled the brakes off three times and checked everything out and it looks good. If slowly push the brakes everything is great, it is only when I have to really slam on them.