Corolla / Matrix 2009-13 :: 2012 - TRD Lowering Springs Installation
I have a 2012 corolla le and I'm looking into getting TRD lowering springs as I don't want to go too low and they work with the stock strut, however; I read that they work best with the XRS' shock and strut (might be just the strut but I'm not sure), my question is what are the XRS' struts called and where would I find them, also from what year would the XRS' struts fit on my le?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 F550 - Overheating Going Uphill
I have a 2006 F550 mini bus, that I just had the head studs done, egr delete and air intake changed. Last night we took it out for a run to test it since we just installed a new fan clutch. We can here the fan kicking on and off. The problem is, we drove it say 60 miles, up and down a mountain, had no issues. We got out and ate for about an hour, and then drove it back the same way. This time on a slight upgrade my check gauges came on, and I seen the temp rising. I let off the fuel, and it dropped back down. So the rest of the way home I was easy on the fuel and made it back with out heating up again.
Today, we took it for a ride and at idle before we left the ECT was 172, and EOT 170, as we drove I watched the temps. Climbing up a fairly steep mountain, we were doing about 65mph, for about a 5 mile climb. During the climb my ECT was 201 and EOT 226, at the hottest point it was ECT 204 and the EOT was 226.
I am assuming it could be a possible water pump and or oil cooler. Reason I am thinking the water pump, is because after it over heated, I noticed if I let off the fuel quick after running I would hear a noise like a puffing sound. It was the coolant shooting out of the degas bottle. It did this several times when letting off the fuel quick, which I think was the pump was allowing the coolant to be pushed back in from the heat.
I already ordered a new pump, which if bad could also cause the oil not to cool as the pump is not pushing enough coolant? (Also I only lose coolant if it gets to hot)...
Ford 6.7L Power Stroke Diesel :: 2015 F550 - Fuel Gauge Not Working
Working on a 2015 f-550 with a 6.7 power stroke. Damaged the wiring harness and fuel gauge not working now. Where could I find a wiring diagram? The low fuel is now causing it to not regen. We have continuity through the wires and they have been repaired but gauge still does not work. Currently now power to fuel gauge sender?
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2004 F550 - Entire Bank Drops Out At Idle
I have a 2004 f-550 sd with a 6.0. I am having a problem with cyls, 2, 4, 6 and 8 dropping out at idle. if you rev the motor up they work fine. Could I have a bad injector oring? Seems that iap pressure is good. And seems funny that it is just the one side.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2016 F550 - Ignition Wiring Harness Diagram?
I need to connect a remote start stop for a bucket truck attachment to this new 2016 F550. Found everything except the ignition wiring harness diagram. Need to know what I can tie in to.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 F550 - Inline Trans Filter Housing Seized
I went to change the small filter that is mounted just behind the radiator and is inline with the 5r100 . with a socket on the bottom all i was able to do was flex the brackets going to the 3 mounting bolts as this thing is on there real good. Looking for examples on unthreading the bottom cup to access filter?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 F550 Cranked Strong But No Start - P2285 Code
I have a 2005 F550 with a 6.0. Recently I have had issues with a long crank before starting at times but once it started there were no issues driving. Yesterday it started up in the morning, made a few stops then it wouldn't start at all. Cranked strong but no start. Had it towed back, sat for an hour or two now it starts again. Put a gauge on it and all readings are good. Did have a P2285 code which the ICP sensor. I do suspect there could be an issue with the egr cooler as it needs coolant occasionally. Could that have anything to do with the no start? Truck has started fine today. Why start sometimes then not?
View 11 RepliesFord 6.7L Power Stroke Diesel :: 2011 F550 - Code P0299 / Faint Ticking Like A Stone In The Tire
What to do 2011 F550 RampTruck 11,850 miles on it the vehicle has been back to the dealer 5 times for the same trouble code P0299. After the last time it was in they had it for 2 weeks seemed to be fixed. Last week one of my drivers was towing a Chevy S10 50 or so miles and heard a very faint ticking like a stone in the tire that got instantly worse and before he could pull over started rapping and stalled out. We towed it back to the dealer they removed the Cab disassembled the engine and found a "blown piston" is there quote. What should we do about this problem the dealer is supposedly fighting with Ford and Ford doesn't want to put in a new engine.They want to fix it instead....
View 12 RepliesFord 6.0L Power Stroke Diesel :: Won't Start After IPR Installation?
So I installed a new IPR valve. Now it cranks but wont turn over. I read something about how the IPR valve has to be 'clocked" in the same exact position it was in when I took it out? Would this cause my truck not to turn over? Truck has never not started before.
When I tightened it down, it was not in exact position as the old one. If I wanted it in exact position as old one, it would have not been tightened correctly. I couldn't make one more full turn around. what do u think???
Ford 6.7L Power Stroke Diesel :: DVD Headrests Installation?
Installing the ford accessory dvd players for trucks? not sure if i want to get them just yet but i am looking into options since i have a sunroof and cannot install an overhead player..or can i? I just want to know what you have to do to install them? do they work good? does the leather match?
View 8 RepliesFord 6.0L Power Stroke Diesel :: Heater Hose Installation?
Had a large puddle of coolant under my '05 X this afternoon after work. Seems it's leaking from the Y connection coming off the heater water control valve. See first pic.
I think it's part number 18472 (labeled with the circled 1) on left side in pic #2. Need to confirm this is the right part and the full part number?
Lastly, how the heck do you change this hose? It's tucked up under the cowl and looks like difficult.
Ford 6.7L Power Stroke Diesel :: Oil Pressure Gauge Installation?
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 RepliesFord 6.7L Power Stroke Diesel :: Clearance Lights Installation?
I remember seeing a few people post about having them installed at the dealer for about 125-150 was this at the body shop or in the mechanic shop?
View 13 RepliesFord 6.0L Power Stroke Diesel :: Head Stud Installation?
I Have two questions on installing studs. Does the 6 oclock dowel position really matter? To me it doesnt make much sense because the timing isnt changed with just studs so there should be no issue with valve clearance and such. Unless something isnt installed correctly.
Also what is the best way to clean the block? I thought Senior Master Tech on youtube had an interesting way with a piece of angle iron.
Ford 6.0L Power Stroke Diesel :: Coolant Pressure Gauge Installation?
Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Remote Mounted Oil Cooler Installation?
I am sure some of use around the forums have seen some of Diesel Tech Ron's videos, well in this video he is installing one of Bulletproof Diesel's remote Oil Coolers on a 6.0
Bulletproof Diesel's remote mounted oil cooler install on a 6.0 Powerstroke - YouTube
I like the idea of these if you ever have to do any work on the Oil cooler or replace it it would make it pretty quick and you don't have top spend a day tearing the engine apart
I haven't hear of too many people having issues with remote coolers set up's like this. Maybe there are some remote oil coloer owners that have em that can shed some light on how they have worked so far on their 6.0's ...
Ford 6.0L Power Stroke Diesel :: Drain Coolant And Oil Before BPD Oil Cooler Installation?
I'm getting pretty comfortable with these forums now. Not sure if this is in the right section, but even if it was, I'm not sure how to find the right one. I recently purchased Bullet Proof Diesel's Air-to-Oil oil cooler along with the BPD oil filtration. I've already drained the oil, but do I need to drain the coolant as well? I have read of people doing a complete flush before even installing a new oil cooler (OEM oil cooler). That way once it is installed, it doesn't have all the grit and sand pumping through it right off the bat. But does it matter with BPD's system? Should I go ahead and drain the coolant completely before beginning this job?
View 10 RepliesFord 6.7L Power Stroke Diesel :: 2015 F550 - CEL Code Oxygen Sensor Performance Bank One Sensor One
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Slight Popping Sound Coming From The Top Coil Area
I blocked off the hpop discharge tube to test for leaks, shop air. I am plugged into the oil rail drivers side, and keep getting a slight popping sound. The first time I did this it took ten minutes to start, so I replaced the top injector seals. The second time it did this after about four minutes, so I took the oil rail to the local shop and they did the ball tube orings in the rail, now I went to put it back on and it does it almost right away.
Am I just pushing the oil out of the injectors? is this normal or should I have NO air noise period? I guess I am not sure how these injectors work, where does the oil go after it enters the top of the injector? It seems like it's coming more from the top coil area, more so perhaps than under the oil rail.