Ford 6.7L Power Stroke Diesel :: Clearance Lights Plug In Connector Location?
Do all New trucks come with the factory clearance light plug-in-connector and if so, where would it be located? The reason I ask, is I'm considering adding the cab clearance lights to my 15 F350. Really would like the factory lights but I hear Recon makes some similar.
View 14 RepliesFord Excursion :: Power Supply For Clearance Lights?
Wiring up my Clearance lights for top of the cab, and for my running boards.
According to my diagrams there is a brown wire running along the passenger kick panel and down the gutter to the rear of the X.
Ford 6.0L Power Stroke Diesel :: Won't Start After IPR Installation?
So I installed a new IPR valve. Now it cranks but wont turn over. I read something about how the IPR valve has to be 'clocked" in the same exact position it was in when I took it out? Would this cause my truck not to turn over? Truck has never not started before.
When I tightened it down, it was not in exact position as the old one. If I wanted it in exact position as old one, it would have not been tightened correctly. I couldn't make one more full turn around. what do u think???
Ford 6.7L Power Stroke Diesel :: DVD Headrests Installation?
Installing the ford accessory dvd players for trucks? not sure if i want to get them just yet but i am looking into options since i have a sunroof and cannot install an overhead player..or can i? I just want to know what you have to do to install them? do they work good? does the leather match?
View 8 RepliesFord 6.0L Power Stroke Diesel :: Heater Hose Installation?
Had a large puddle of coolant under my '05 X this afternoon after work. Seems it's leaking from the Y connection coming off the heater water control valve. See first pic.
I think it's part number 18472 (labeled with the circled 1) on left side in pic #2. Need to confirm this is the right part and the full part number?
Lastly, how the heck do you change this hose? It's tucked up under the cowl and looks like difficult.
Ford 6.7L Power Stroke Diesel :: Oil Pressure Gauge Installation?
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Head Stud Installation?
I Have two questions on installing studs. Does the 6 oclock dowel position really matter? To me it doesnt make much sense because the timing isnt changed with just studs so there should be no issue with valve clearance and such. Unless something isnt installed correctly.
Also what is the best way to clean the block? I thought Senior Master Tech on youtube had an interesting way with a piece of angle iron.
Ford 6.0L Power Stroke Diesel :: Coolant Pressure Gauge Installation?
Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Remote Mounted Oil Cooler Installation?
I am sure some of use around the forums have seen some of Diesel Tech Ron's videos, well in this video he is installing one of Bulletproof Diesel's remote Oil Coolers on a 6.0
Bulletproof Diesel's remote mounted oil cooler install on a 6.0 Powerstroke - YouTube
I like the idea of these if you ever have to do any work on the Oil cooler or replace it it would make it pretty quick and you don't have top spend a day tearing the engine apart
I haven't hear of too many people having issues with remote coolers set up's like this. Maybe there are some remote oil coloer owners that have em that can shed some light on how they have worked so far on their 6.0's ...
Ford 6.0L Power Stroke Diesel :: Drain Coolant And Oil Before BPD Oil Cooler Installation?
I'm getting pretty comfortable with these forums now. Not sure if this is in the right section, but even if it was, I'm not sure how to find the right one. I recently purchased Bullet Proof Diesel's Air-to-Oil oil cooler along with the BPD oil filtration. I've already drained the oil, but do I need to drain the coolant as well? I have read of people doing a complete flush before even installing a new oil cooler (OEM oil cooler). That way once it is installed, it doesn't have all the grit and sand pumping through it right off the bat. But does it matter with BPD's system? Should I go ahead and drain the coolant completely before beginning this job?
View 10 RepliesFord 6.7L Power Stroke Diesel :: 2012 - Installation Of F550 Coil Springs?
I have a 2012 F350 CCLB with camper package (front coil springs @ 6,000 lbs). I was thinking of installing F550 coils springs, which are rated at 7,000 lbs, to provide greater lift up front.
Before performing this modification, what lift was achieved up front?
My endeavor is not to achieve level, per se, but rather allow for increased tire size, such as 35's and ground clearance.
Ford 6.7L Power Stroke Diesel :: Clearing Codes After Installation Of Fresh Sensor?
Anyways, so if replace an egt sensor how soon do I have to clear the code after install of a fresh sensor? Could I replace it in my garage and then head to autozone and borrow their scanner or do I need to do the replacement in their parking lot and do it right after the installation? It's my old mans truck and he doesn't have a scanner for his rig.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Installation Of Washer Fluid Pump?
I am a new owner of a 2006 F 250 6.0.
I need to install a new washer fluid pump. My question is what is the best way to get the old one off and the new one on? Should I go from under the wheel well? Or is there another easier way to get to it? The truck didn't come with an owners Manuel and I cant find anything about how to do this.
Ford 6.0L Power Stroke Diesel :: 2003 - Coolant Pouring Out The Tail Pipe After BPD Oil Cooler Installation?
My buddy install a BPD air/oil oil cooler in his 2003 F250 last week and now there is coolant pouring out the tail pipe. I haven't seen it but he tells me there is quite a bit coming out. It wasn't doing this before we installed the BPD oil cooler. Normally I would say bad EGR cooler but his EGR is deleted. This is the 3rd BPD cooler I've put in and this is the first time I've had any issues after the install. The install went smooth other than we broke the radiator and had to install a new one. I feel bad cause I'm hoping it wasn't something I caused but I just can't think of anything I did during this install that would cause coolant to be getting into the exhaust. He just had it towed to the local Ford dealership.
View 3 RepliesFord 6.7L Power Stroke Diesel :: 2013 - Install Flashing LED Lights To Work In Conjunction With Hazard Lights?
I have a 2013 6.7l super duty Lariat. I want to install flashing LED lights to work in conjunction with the hazard lights. The leds have their own controller and will be separate from any other lights/wiring. What I need is some way to trigger a relay to turn on the led's. Was hoping to tap into the hot lead off the hazard switch itself but that's not an option!
View 2 RepliesFord Excursion :: Cab / Clearance Lights Stopped Working
All five clearance lights on my cab stopped working, and I can't figure out why. I've read all the threads, but few show the wiring, and are more useful for installing than troubleshooting. I think I have the Ford SKU'd ones, not the Recons, but I can't say for sure. Here's what one of them looks like:
My questions:
1) How do you remove the bulb from the rubber mount? Just pulling it out didn't work.
2) Is there a fuse somewhere (in the harness, perhaps?) that protects these things? All my overhead console functions and lighting work fine.
3) Is their only connection to the vehicle wiring at the harness connector behind the passenger kick panel? I checked it, and it is well connected.
4) Is there a connection on the headlight switch? I've not checked there.
I bought this vehicle 14 years ago and they were already installed, and have worked perfectly since then. I hate stuff that doesn't work...
Ford 6.7L Power Stroke Diesel :: Lost Power For Running Board Lights
I added LED lights to illuminate the running boards on my Lariat. Did this about 15 months ago and all was fine until this week and I noticed they weren't coming on any longer. Both sides are out of commission. The running board lights on each side are wired to the respective plug for the running board lights on each side. The interior lights that are on the same circuit work fine (fuse #12 in the passenger side fuse box).
So I'm scratching my head trying to figure out why both sides have gone out at the same time but the fuse is ok. It's winter here and my truck doesn't completely in the garage so I'm hoping to limit my time lying under the truck out in the cold, on a wet floor! I thought there might be another fuse in the engine compartment fuse box but there isn't, at least according to the manual.
Ford 6.0L Power Stroke Diesel :: No Power To R/H Mirror - LED Lights Do Not Work
2007 F250SD, R/H power mirror with LED lights no work. All other lights and L/H mirror work fine. Checked the fuse in passenger compartment, it's good. Where to start looking?
View 5 RepliesFord Super Duty (1999-2016) :: LED Clearance Lights Gone Out
A few of my clearance lights have gone out... and I'm looking to replace them. I was told the bulb type was "194" and was wondering if I could just drop in some 194 type LED bulbs like these, in amber color without changing anything else [URL] ..... I'm assuming it will plug right in but wanted to make sure
View 14 Replies