Ford 6.0L Power Stroke Diesel :: 2003 F250 - Truck Won't Crank Anymore After ICP / Oil Cooler Repair
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
Ford 6.0L Power Stroke Diesel :: Got EGR - Installed Oil Cooler - Crank But Won't Start?
Long story short: Got EGR Cooler and Oil cooler installed last week. New headgaskets and bolts. New down pipe. New orings on injectors. HPOP was installed 3 months ago before any of the above work.
Truck drove great for about 100 miles. Then stalled at a stop light. Restarted it. Drove another 10 miles. Truck then dies on me at 25mph. Wouldn't restart immediately. 10 minutes later it started. I drove it back home (couple miles). When i hit the last stop light, the idle immediately changed to crap. Very rough. Got home and parked it and since then I have not been able to start it.
I changed the EGR Valve, tried to start it and it wouldn't. Changed IPR Valve. Put all back together. No start. Cranked beautifully. But doesn't sound like it's taking fuel. note - no buzz/clicking from injectors and no fuel pump noise.
Here are my readings. FICM Sync - 1. I am stumped. I did recommended KOEO, checked emergency fuel switch reset, batteries are at 13.5 avg, checked harness wires and found one connector that wasn't snapped in cause the retaining clips were broken. Getting this connector replaced. Found another wire below chaffed. It is on the intake manifold. what is it for and could this be my problem? Pic below? This is where it connects to intake chaffed. The top of the two wires where they go into the connector were twisted around each other. Maybe wire to wire, maybe not. Would this cause my injectors to not buzz or fuel pump to not come on???
Ford 6.0L Power Stroke Diesel :: Changed Oil Cooler And Welded EGR Shut Now Crank But No Start
Swapped a new oil cooler and welded Egr shut. Truck ran fine the first 3-4 times I started it except for exhaust leak at the y-pipe/turbo connection. Tried to start it today and it started then ran real rough, blowing whit smoke. Now it will not start at all and blows whit smoke. The only codes I'm getting are egr codes that I've always had due to having the 05 and up intake elbow and the egr turned off via sct. What could be the issue?
View 8 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start / No Crank - Code P2285
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Truck Will Not Start / No Crank
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesFord 6.0L Power Stroke Diesel :: Crank No Start - Truck Sounds Like It Is Almost Firing Up But Still Cannot Get It To Run
Had extreme cold weather here and I left my truck unplugged for a couple of weeks. Started fine but stalled once the fuel was used up in the lines. Replaced fuel filer and filled with that anti gel stuff. Truck sounds like it is almost firing up but still cannot get it to run. When I turn the key on it sound like the fuel pump is working for about one minute and then turns off. Made sure the fuel filter was overfilled with deiseal. Turned it over so many times the lines should be full by now. I used that quick start stuff and it almost starts every time.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2004 - No Crank After Installing A New Oil Cooler
After installing a new oil cooler my 6.0 will not crank over and I have no injector noise or communication with my scanner , that is until I unplug the center connector to the PCM then injectors come on and engine cranks and pcm communicates with the scanner....
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Engine Change Out Now The Truck Will Not Start On Hot Crank
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 RepliesFord 6.0L Power Stroke Diesel :: Possible Plugged Oil Cooler Or EGR Cooler?
I have a 04 that has 153k on it. 4" cat back exhaust with no cat. SCT tuner running a custom street tune. New FMIC with the extra tune on it. Head gaskets where done at 90k along with ARP studs. EGR cooler, The oil cooler was cleaned, New coolant tank. 1-new head and The cooling system was flushed at 90K. All done by the dealer along with some other items. Installed a bypass coolant filter at least 60k miles ago.
I have been having a no heat issue sometimes at idle this past winter and a mystery loss of coolant. I replaced the cap with a OEM one. I did a vacuum test on the coolant it held at 25 inches for well over a 1/2 hour. Pulled the egr valve it looked somewhat like tar inside not 100% dry. At startup it sometimes blows some white smoke and other times it's black smoke. I've had the scan gauge on for the last week to check my deltas.
Running 65mph the deltas stayed around 10 degrees diff.
Running 70mph the deltas stayed around 14-16 degrees diff.
Yesterday just running around rural roads 55mph and under the deltas stayed around 10 degrees diff.
I have not found a lower pressure gauge to do a coolant pressure test.
It does look as though it has burped the cap. Because of the deltas I'm thinking a plugged oil cooler my be the problem.
Ford 6.0L Power Stroke Diesel :: Intermittent Start After Oil Cooler Replacement
I had a bunch of down time from knee surgery and needed to replace the oil cooler. All OEM parts were used except for egr cooler being sinister that came new but hadn't installed. Truck ran fine but deltas were getting 20-25 while unloaded. I have replaced some of the pigtails when needed, but having it apart for the other work. I looked very close at the main engine harness which was oil soaked and carefully unwrapped it checking for any problems. A couple of the pigtails were replaced and all re wrapped with abrasive type tape. All connections looked good but hit the key and no start just cranking over. Did it a couple more times and it fires but rough. Trying again and it's sounding new. Shut off re try no start. I didn't touch anything other than egr cooler oil cooler and wiring harness...
Koeo. Koer
Ipr 14.8. 33.4
Icp. 2. 950
Icv .23. 1.09-1.43 fluctuated
Ficm in 12.9v cranking 48.5 and 48.5 running.
Batteries are fully charged with trickle chargers
13.9 at batteries
Fuel bowl is 57 then 55 if it starts.
Every so often it's showing ficm sync 1 and sync 1 and starts and runs smoothly. It's non consistent. I've checked continuity and get from pcm pins 2ohms resistance. I'm thinking wiring harness but really cleaned it and checked it thoroughly. I've hit the wall. How to track down my issue?
Ford 6.0L Power Stroke Diesel :: 2006 Truck Would Not Crank At All
So I went to start my 2006 this morning and it would not crank at all. Like the battery was dead ( all the light in the cab and headlights were working fine. ) so I tried to jump it and still nothing no clicks not crank no nothing. Just for fun I went ahead and jumped the starter (using the same method as when I prime the hpo system) starter cranked no problem so I put the key in the on position and cranked the key again still nothing. So I put the key in the on position again and jumped the starter truck fired right up. So I went back in the cab and tried to start it with the key and it started right up like nothing ever was wrong. What was causing this? Also my voltage was at 11.5 with the key on and engine off when it was running the volts were at 12 to 12.5
View 5 RepliesFord 6.0L Power Stroke Diesel :: Truck Does Not Even Crank And It Has No Fuel Pressure
I was driving to a job this morning with my truck loaded with tile for a job and it just died.
It has power to the lights, radio, etc. But when I try to start it it does not even crank and it has no fuel pressure on the gauge and the pump is no running.
It is as if the truck has no power. When it died is was like I turned the key off and it just stopped.
Ford 6.0L Power Stroke Diesel :: Truck Will Crank Longer Than Normal When Parked
I have noticed that my truck will crank longer than normal when i park backed into my drive way but it only does it every now and then. I am guessing an internal oil leak but it starts fine cold or hot.
View 10 RepliesFord 6.7L Power Stroke Diesel :: Truck Quit - Stop Safely Now Message And Won't Crank
Luckily I was sitting in the driveway. Pulled the truck out of the garage. It started fine, idled fine, did not make as much noise as I was expecting but was warmer in the garage than outside. Stopped in front of the garage door to grab a couple things in the garage, jumped back in and it quit before I could get it in gear and roll out. Weird. This is the first time I've ever had to get a tow.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Keeps Dying And Have To Crank For About 15 Seconds To Start Again
Alright, my 1999 7.3 keeps dying on me in the morning. About two weeks ago I noticed it started to have a weaker start up, even though it has two brand new batteries. Once it starts up, I get around the block and it dies there every time. Then I have to crank it for about 15 seconds for it to start again.
The crank gets faster and faster until it finally start, and the engine is very choppy, like its starving for fuel. After about ten seconds of that it return back to a smooth idle. I then take off, and about 50 yards later it does the same thing. After it does it the second time, the truck runs just fine for the rest of the day with no problems.
I have noticed that when if I turn the truck on and let it idle for 10 minutes first in the morning, it won't die on me. I replaced the camshaft position sensor thinking it was that, but it wasn't.
Ford 6.0L Power Stroke Diesel :: Hot Crank No Start Sometimes
The truck was running fine then I shut it off one day and it wouldn't start back up long powerful cranks but wouldn't start pulled the valve covers checked branch tubes and dummy plugs all looked good (not for sure though) replaced the icp and even tried unplugging it after the hot crank no start to see if that worked because that was the only a code I threw but alas it did not work.
I did a air test and closed the IPR valve via fancy tool and was getting some minor gurgling out of the oil filter resivuar and was guided to change the hpop being that was the beloved issue I couldn't get the j-tube out to inspect but everything else was clean as a whistle ... I was getting some air flow threw the oil filler cap and the air intake box on the driver's side valve cover but was told that is normal but not sure how normal when I replaced hpop it appears it stopped gurgling as much.
When I did the following air test but it started when cold but then it struggled but it did start then my batteries died out turns out I do have a bad negative connection I getting the batteries re charged gonna pick them up today and tighten that connection along with a new air filter via reading in the hanes manual that can sometimes cause a hot crank no start .
Ford 7.3L Power Stroke (1999-2003) :: Block Heater Plugged / Truck Crank But Won't Start - Fix?
When the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.
Ford 6.0L Power Stroke Diesel :: 2004 - Crank But Won't Start?
I have a 2004 6liter. I parked one day two weeks ago and a went out last week to move it and I will only crank over. No fire No start!!!! Have new batteries. New fuel filter and have fuel coming in to the fuel bowl. I have gone over the harness, checked my fuses. I do not have a reader or scanner. Any recommendations. I want more than just a code scanner.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Crank But Won't Start
I was driving down the road and suddenly lost tons of acceleration power had to almost flour it to move at all so I pulled off the road to stop and check it out. After I stopped I couldn't get it to start again it would crank like it wanted to start but nothing. So I had I towed home and it sat for a little while and then I tried to crank again, and it started and idled like crap and when I pushed down on the gas pedal there was no reaction, rpms didn't go up or nothing but still would idle like crap.
Symptoms stayed the same for about a day and no I have a crank no start. So then I did what little I could do just to see if it was an easy fix I changed the ICP sensor, IPR sensor, and EGR valve needed to be replaced so I replaced that too. Headstuds and gaskets have been done as well by previous owner but not I think it might be an HPOP problem? I am unable to read codes at the moment as well just FYI. Could this be a fuel filter issue even tho the secondary housing fills with diesel?