Ford 6.0L Power Stroke Diesel :: Truck Does Not Even Crank And It Has No Fuel Pressure
I was driving to a job this morning with my truck loaded with tile for a job and it just died.
It has power to the lights, radio, etc. But when I try to start it it does not even crank and it has no fuel pressure on the gauge and the pump is no running.
It is as if the truck has no power. When it died is was like I turned the key off and it just stopped.
Ford 6.0L Power Stroke Diesel :: Truck Won't Start / Crank After Oil Cooler Rebuild
Had to do the icp sensor originally. went in from the top and discovered my oil cooler was failing too. so i did that. with weather (too tall to fit in the garage) and life getting in the way it's taking me 2 months a little here n there to actually get it done so she's sat for a while. yesterday was moment of truth to get it started again. the batts were old before i started working on it. so i replaced those yesterday.
I've tried and tried to get it to start and it won't turn over. it did for one tenth of a second try. nothing since. I saw that my shifter wasn't exactly in park so i wiggled it and tried to crank it again and now it won't even crank. I have a feeling somehow the transmission isn't reading in park or neutral so it's refusing to crank. I really don't want to tow it.
Ford 6.0L Power Stroke Diesel :: Truck Won't Start / No Crank - Code P2285
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Truck Will Not Start / No Crank
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesFord 6.0L Power Stroke Diesel :: Truck Will Crank Longer Than Normal When Parked
I have noticed that my truck will crank longer than normal when i park backed into my drive way but it only does it every now and then. I am guessing an internal oil leak but it starts fine cold or hot.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Crank No Start - Truck Sounds Like It Is Almost Firing Up But Still Cannot Get It To Run
Had extreme cold weather here and I left my truck unplugged for a couple of weeks. Started fine but stalled once the fuel was used up in the lines. Replaced fuel filer and filled with that anti gel stuff. Truck sounds like it is almost firing up but still cannot get it to run. When I turn the key on it sound like the fuel pump is working for about one minute and then turns off. Made sure the fuel filter was overfilled with deiseal. Turned it over so many times the lines should be full by now. I used that quick start stuff and it almost starts every time.
View 9 RepliesFord 6.7L Power Stroke Diesel :: Truck Quit - Stop Safely Now Message And Won't Crank
Luckily I was sitting in the driveway. Pulled the truck out of the garage. It started fine, idled fine, did not make as much noise as I was expecting but was warmer in the garage than outside. Stopped in front of the garage door to grab a couple things in the garage, jumped back in and it quit before I could get it in gear and roll out. Weird. This is the first time I've ever had to get a tow.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Truck Won't Crank Anymore After ICP / Oil Cooler Repair
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Engine Change Out Now The Truck Will Not Start On Hot Crank
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - No Crank No Start
I have a 2006 F250 6.0 with 218xxx on it. Have had a ton of issues since day one, but I finally thought I had gotten a handle on all of them until the other day. Truck started sounding a little rough, no noticeable effect on performance, no codes on my Edge CTS (except one random CKP sensor code that went away). Was leaving work later that day to go home and it started up fine.
Got about a 1/4 mile from the shop and went to turn onto a busier road so I put into the pedal a little bit. Truck immediately lost power. Sounded like a turbo boot blowing and I had very little throttle response. Immediately pulled over and checked codes with truck still on, nothing. Got out and popped the hood with the truck still idling to check for CAC tube/boot etc. As I was looking at it, the engine started screeching. I shut it off as quick as I could get back to the cab.
Looked over everything, nothing noticeably wrong. Went to crank it to see what it would do. All i got was a noise from the starter engaging. Belt not turning over. Tried unplugging the fan clutch (read a thread with similar symptoms and that was the issue for them), connected the starter solenoid directly to battery, same issue. Removed belt and attempted to crank. Same thing. Removed all glow plugs to check for hydrolock. Motor slowly would turn with belt still removed and no glowplugs. Removed starter and tested outside of vehicle, solenoid and motor both seem to be ok.
Ford 6.0L Power Stroke Diesel :: 2006 F250 Crank But Won't Start
I have a 06 6.0 f-250 it cranks but won't start untill I pull the secondary fuel filter cap off and seems to vent air in the system out then it starts right up. I can't figure out where it's sucking air. Here's my question I changed the fuel sending unit in the tank a few weeks ago and had a hard time seating the lid on top of fuel tank. If it is not completely seated will this cause air in the fuel system and give me the headache I've been dealing with?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Died Now Crank But No Start
My wife and I went on vacation for our anniversary and the truck ran fine for a while then we went back to get ready and when we left it started up and everything seemed fine but it died about 200 yards later and is now cranking but not starting. Left my toolbox at the house (stupid!) And truck is new to me so I don't have gauge or reader. Checked the fuel filter under the hood and fuel pump is pumping. Any other tips on what to do that could be the problem without buying parts?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - Long Crank Time
I have a 2006 F350. I have long crank times. No Codes. I have Autoenginuity with Enhanced Codes and everything shows fine. I replaces standpipe and dummy plugs. Glow Plugs and harness. I was hoping it not be the STC but I needed to do oil cooler so wanted to eliminate STC. Got truck apart and the STC Fitting is newer style so I'm kinda bummed out. Not sure if I'm missing something and as far as I have it torn down is there anyway to test what could be causing the problem? Or just put it back together and keep my fingers crossed that whoever put the new STC fitting in screwed it up. I'm beginning to not like my truck.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2006 E350 Stalled While Driving Now Crank But Will Not Run
A friend brought to me this 06 E350 with a 6.0, which stalled on him while driving. The van will crank over good and strong, but won't run. It will how ever fire, and almost run until you let the key back (i would describe it as it does run with assistance from the starter). the FICM has 12V in and 47.5V out. And ICP is around 650 psi till it fires then it raises to 1215 psi. there are no codes either - I'm not familiar with these 6.0l...
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Oil Pressure Only Going To 350 PSI / Crank Longer When Cold
I have a 2006 f250 6.0 203,00 miles. At 196,000 miles turbo went out, bought power max turbo, redid head gaskets with studs, had heads shaved flat, replace oil cooler with ford part, egr delete, custom tune, aftermarekt 48 Volt FICM.
Truck ran great until 1 day didn't start. had to let truck cool down and then it stared oil pressure was only going to 350psi. drove home fine, shut it off and wonted start hot. drove it a few times after that just let truck idle. Then it started to crank longer when cold. Replaced dummy plug and stand pipe on drivers side only. Then truck was ok for a few drives then started to get a studer sometimes when idling. It got worse then was getting a misfire cyl 1 then, truck died 1 day turning around and would only build a 200 psi.
Replaced stand pipe and dummy plug on passenger side, and IPR, now getting misfire on cyl 8 and P2284, truck runs like crap, bad idle, rpms weird/gas pedal. idle is higher than it should be. when truck is first started shacks very bad, engine very nosiey. ICP 1046 psi(1.27Volts)Desired 637.9, idle and ipr 14.84, truck idles ok, when u punch gas revs up and comes back down, misfire gets worse with rpm.
Then icp goes to 870(2.23 Volts)Desired 870 and doesn't change when getting on the gas and ipr 32.42, punch it and rpms go up more then come back down. Truck starts to shake again. Could running it for so long with bad oil pressure or to much air wreak the injectors? When cold can shut off injector 7 or 8 doesn't change idle like all others do. Once warm 7 or 8 does make a small change in idle. If i command ipr to 20% idles fine, but icp no change from 32.42% to 20%...
Ford 6.0L Power Stroke Diesel :: 2006 - Replaced 1357 Injector - Crank But No Start?
2006 6.0 king ranch 189k sct live wire Replaced 1357 injectors and when I crank truck it will crank and sputter for a brief second but will not fully start and continue cranking and doing this over and over. Tried starting for roughly 30 minutes would not budge. Tested icp and ficm both are good. Also replaced batteries, fuel filters, checked all relays and fuses still can't figure it out. Also truck is bulletproofed.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Rough Idle / Dies Warm And Long Crank
My 06 currently has 296k miles. 3 years ago I put a lot into her. Dummy plugs, stand pipes, STC, hg,studs, oil cooler, bpd egr cooler. Cleaned spool valves and fresh o rings in injectors. (Alliant) plus a lot more that I can't remember. Ran very very well after all that.
Fast forward to a few weeks ago. Driving down road and truck died as I let off pedal to slow down for turn onto my road. Took about 7-8 tries to get started back up. Icp was reading in the 300's until it finally started. Made it home. Shut it off. And started right back up.
Few days later truck died again same way. Let off to make a turn. Several attempts to restart icp was in the 300's again. Once it started building 420ish it sounded like it was firing a few injectors and slowly started running. The next time it happened the same way but when I got it back running I eased to my inlaws like less than a mile. When I got to their house and pulled in and went to back up to turn around the display on dash said low oil pressure and started missing a little. So once I got home started researching.
A few days ago I pulled out the low pressure oil regulator to check it out. It was clean but did have some mild scaring. I used some fine scotch rite and smooth it out a a little. It moved freely in the bore so I put it back together. Then pulled the oil filter cap off to check the little black valve. I noticed the filter was not dripping with oil like normally when I change the oil. And yes it's motor craft filter and cap. It checked out ok. Press it down and turned engine over and it filled and held. Let off of it and it drained.
Next I air checked the high pressure side. Applied air and waited until I could hear the air (IPR still open) then closed the IPR. Couldn't hear any leaks. Just a very very minor his and couldn't pin point where. So I went ahead and went to dealer and got new stand pipes and plugs. And ordered new print set for injectors. Pulled injectors and didn't see any smoking guns. Replaced prongs, stand pipe and dummy plugs and put it all back together. Cleaned the injector cups and hold down bolt holes. Torqued injectors to spec.
Got it all done and rotate motor by wire next to heater blower to assist prime system. Tried to start it up and it took two tries but fired right up and sounded smooth as hell. After it idled a few minutes I saw a haze from exhaust. It smelt just like fuel. A few minutes later started idle a little rough. Gave it some go pedel and it was rougher at about 1600-1800rpms and couldn't feel it above 2k. Got my laptop out with AE and done balance test. Did not show anything. No codes either.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - Lost Power When Step On Gas And Truck Wouldn't Exceed 15 Mph
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2006 - No Start / Truck Will Not Kick Over
Just replaced injector 4, oil cooler and did egr delete. Ficm is at 48 and truck will not kick over. New batteries installed.
View 14 Replies