Ford 6.0L Power Stroke Diesel :: Part Number For High Pressure Oil Rail Check Valves
What is the part number for the high pressure oil rail check valves for a 2003 6.0L? I'm referring to the ones that screw into the oil rail. I would like to avoid the local dealer if possible.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Cylinder Head Fuel And Oil Rail Plug ORing Replacement
Is this job worth doing as a preventative maintenance item? I replaced the rear fuel rail plug (aka banjo bolt) o-rings because they were very easy to get to with the up-pipes out. But the cylinder head plug in the rear is pretty high up and even with the up-pipes out, there isn't enough room to get a breaker in there that's long enough and has enough movement to loosen it. The front would be easier to get to, but both accessory brackets need to come off to get to them on both sides.
As far as I know, none of them leak but they're all 17 years old... BTW in case you haven't been following, I'm doing up-pipes, injectors, turbo, rebuilt HPOP & fuel bowl, boots & clamps, etc. so I'm trying to knock out any PM items while I have it apart.
Ford 6.0L Power Stroke Diesel :: ICP Sensor Part Number?
Looking to confirm the part number. My ICP is mounted on the RH valve cover and has a yellowish upper where the three pronged connector inserts.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Metal CAC Tube Part Number?
I found 2 Ford OEM part numbers for what seems to be the same identical metal CAC Tube for the drivers side.
6C3Z-6C640-AA
and
6C3Z-6C646-BA
I wanted to place an order today for my '06 but want to make sure it's the right one. What is going on here? (maybe one is for a '03-04) I Don't know...
Ford 6.0L Power Stroke Diesel :: Top Of Engine Fuel Filter Part Number?
With an AD2 and no HFCM, need to have a part number for just the top of engine filter? All I can find (Motorcraft, AMSOIL, Racor) are the dual filter kits.
View 4 RepliesFord 6.0L Power Stroke Diesel :: IH Part Number For The Fuel Return Tube
When I went to do my fuel filters tonight I found that the Fuel Return Tube had broken. I have the Ford part number 3c3z-9t289-AA and was looking to see what is the IH part number. I think I'll pick up that oil filter assembly too.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Intake Elbow Gasket / O-Ring Part Number
I need to remove my EGR valve to clean the unit of carbon. While there I will be removing the intake elbow to check if I have the throttle plate installed on my engine. What the part number is for the gasket / o-ring that seals the elbow to the intake manifold??
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 4X4 Front Hub Bearing Part Number?
Can't seem to find a number for just the bearing and snap ring. All I can find are the dang assemblies.
View 11 RepliesFord 6.0L Power Stroke Diesel :: A/C High Pressure Cutoff Switch - Part Number
Probably needs to get, f I had a part number for the A/C high pressure cutoff switch, and the 4 wire connector (2006 MY)? I guess for the 6.0L it is actually called "Dual Function Pressure Switch, DFPS".
Was dealing with some chaffing and wanted to add to my "parts list spreadsheet".
Base numbers:
A/C high pressure cutoff switch: 19D594
A/C cycling switch: 19E561
Found the clutch connector part number: Aftermarket - DD1085
Probably need to call this thread "I hate electrical problems also!"
Ford 7.3L Power Stroke (1999-2003) :: PCM Ground Clip Part Number?
Does that little clip that grounds the PCM case have a part number? I've been troubleshooting an "SES - but no codes that would cause it" issue, and noticed tonight that clip is not there. Even a photo would work, as I assume I could make one if I had to. It's just a piece of copper, right?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacement Water In Fuel Sensor - Part Number?
Looking for the Ford (or even Dorman) part number for the Water-in-Fuel sensor that bolts to the outside of the fuel bowl?
Guzzle has it pictured here:
The water sensor tip on mine is badly corroded and eaten away.
What's a part number and who sells them that I can get it delivered next day?
Ford 6.0L Power Stroke Diesel :: ORing Leak Where EGR Cooler Meets With The Intake
I I have a pretty good o ring leak where the egr cooler meets with the intake. My question is can i replace the o ring without removing​ the intake. If so what is the process.
View 2 RepliesLexus GX 2004-09 :: Part Number For New Plug Wires For 07 GX470?
I have been trying to find the part number for new plug wires for my 07 GX 470 and have searched the forum and all I can find on the internet is just the boots? I have 104K on my vehicle and was going to put DENSO plugs and wires on it.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Hydroboost High-pressure Line Coupling Leak - Replaced ORing?
I've been watching fluid build up on what I think is the hi-pressure line on the hydroboost. It appears to be originating at the coupling in the line because it is dry back at the unit.
Is there an o-ring or nylon washer in this fitting?
Can it be tightened?
Does the o-ring or washer need to be replaced?
Is it a sign of something else, like a build up of pressure in the line that is too high?
I currently have zero problems or noise coming from the steering or brake system.
Ford 6.0L Power Stroke Diesel :: High Pressure Oil Rail End Caps
I was watching a tv show a while back, I cant find the episode but I think it was performance tv, and they had a 6.0 L expert on there and he was saying they see a lot of high pressure oil rail end caps come loose and or pop out. He was saying that they tap/thread the end of the oil rail and put a threaded in cap? Does it make any sense, can it be done, is it worth doing?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Reconnect High Pressure Oil Line To Rail?
I've found everything there is to know about disconnecting the high pressure oil STC line from the oil rail on the early 6.0's, but I can't find anything about reconnecting them. Do you simply press it back on? Should there be an audible "click"?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Long Crank Time To Start After Oil Rail Removal
Removed my oil rail to replace standpipes/dummies (04 Wavy rail) and now I have huge crank times to start. This is after the initial Huge crank to get it started. Do I have air in the system, or did I bugger something. I did the whole deal very careful. I lifted the rail up very carefully, pipes removed. I lined up the rail nipples with the injectors and evenly pressed it back in place, and then inserted my dummies/standpipe. Tightened the rail to 120 inch lbs then the dummies/standpipe to 60 ft lb. I did my son's '06 a month ago with no troubles. (didn't remove rails though). Once running it sounds perfect, turn it off and re-start and it's a long crank (30 seconds or more). I have not monitored ICP/IPR while running, will try that today.
View 8 RepliesFord 6.7L Power Stroke Diesel :: Increase In Number Of Flashes For Turn Signals?
Love the turn signals of flashing 3 times if you just tap it. It will flash 5 times on the tap when you are pulling my rv. Is there a way to increase the number of flashes? Say 3 to 5 and 5 to 7. Couldn't find anything in the owners manual.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2004 - F350 - Door Lock Keypad Number?
04 f350, how do i get the door lock keypad number?
View 9 Replies