Ford 6.0L Power Stroke Diesel :: IH Part Number For The Fuel Return Tube
When I went to do my fuel filters tonight I found that the Fuel Return Tube had broken. I have the Ford part number 3c3z-9t289-AA and was looking to see what is the IH part number. I think I'll pick up that oil filter assembly too.
View 4 RepliesFord 6.0L Power Stroke Diesel :: ICP Sensor Part Number?
Looking to confirm the part number. My ICP is mounted on the RH valve cover and has a yellowish upper where the three pronged connector inserts.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Top Of Engine Fuel Filter Part Number?
With an AD2 and no HFCM, need to have a part number for just the top of engine filter? All I can find (Motorcraft, AMSOIL, Racor) are the dual filter kits.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Oil Rail Plug Oring Part Number
I'm doing standpipes and dummy plugs. There is a 4mm plug with an oring and mine was trashed. What is the P/N?
View 13 RepliesFord 6.0L Power Stroke Diesel :: Intake Elbow Gasket / O-Ring Part Number
I need to remove my EGR valve to clean the unit of carbon. While there I will be removing the intake elbow to check if I have the throttle plate installed on my engine. What the part number is for the gasket / o-ring that seals the elbow to the intake manifold??
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 4X4 Front Hub Bearing Part Number?
Can't seem to find a number for just the bearing and snap ring. All I can find are the dang assemblies.
View 11 RepliesFord 6.0L Power Stroke Diesel :: A/C High Pressure Cutoff Switch - Part Number
Probably needs to get, f I had a part number for the A/C high pressure cutoff switch, and the 4 wire connector (2006 MY)? I guess for the 6.0L it is actually called "Dual Function Pressure Switch, DFPS".
Was dealing with some chaffing and wanted to add to my "parts list spreadsheet".
Base numbers:
A/C high pressure cutoff switch: 19D594
A/C cycling switch: 19E561
Found the clutch connector part number: Aftermarket - DD1085
Probably need to call this thread "I hate electrical problems also!"
Ford 6.0L Power Stroke Diesel :: Part Number For High Pressure Oil Rail Check Valves
What is the part number for the high pressure oil rail check valves for a 2003 6.0L? I'm referring to the ones that screw into the oil rail. I would like to avoid the local dealer if possible.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: PCM Ground Clip Part Number?
Does that little clip that grounds the PCM case have a part number? I've been troubleshooting an "SES - but no codes that would cause it" issue, and noticed tonight that clip is not there. Even a photo would work, as I assume I could make one if I had to. It's just a piece of copper, right?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacement Water In Fuel Sensor - Part Number?
Looking for the Ford (or even Dorman) part number for the Water-in-Fuel sensor that bolts to the outside of the fuel bowl?
Guzzle has it pictured here:
The water sensor tip on mine is badly corroded and eaten away.
What's a part number and who sells them that I can get it delivered next day?
Ford 7.3L Power Stroke (1999-2003) :: A/C Leak Coming From Metal Tube Going Into Spongy Area
So after a hot drive yesterday we thought to do some googling about our clutch cycling on and off so fast. Yep, the airgap was out of spec. Fixed that.
Then we added some refrigerant to the truck. The truck is "new to us" and this is our first summer with it so not sure what might've gone on previously with the AC. Didn't take long to find a rather sizable leak. :P
See that metal tube going into the "spongy" area? Yeah, that's where it seems to be coming out. That tube is the only one that's cold, the rest are ambient temp. We fix a lot on our jeeps, but the AC system is naturally a bit out of our wheel house since it's not something you normally tangle with. Is this an easy fix? Or do we need to take it in to get serviced?
Ford 6.0L Power Stroke Diesel :: A/C Leak Found - Rubbing Metal To Metal Caused The Pinhole
Getting the RV ready to go for the summer, and no a/c. I started to add freon, and found the leak right away.
It's on the 3/4" pipe that goes right over the upper radiator hose; obviously rubbing metal to metal caused the pinhole. Now I know where that mystery green snot came from all over my radiator hose coming back from Yellowstone last fall.
First thought was to replace the entire pipe. There's an easy threaded connector on the upper end, but way down on the compressor is a strange fitting that looks like a triangle stuck against a cube. I can't see how I'd get a wrench in there very easy anyway. What is that fitting?
I bought a Dorman 3/4" repair kit, but until it arrives in the mail I don't know if I've got enough straight pipe to work with. Do I need to add oil as well as freon once I charge the system again?
Ford 6.7L Power Stroke Diesel :: Truck Makes A Metal On Metal Screech When Downshifting From 5th To 4th And 4th To 3rd Occasionally
I've had transmission issues with my truck that the dealers can't seem to duplicate. The truck makes a metal on metal screech when downshifting from 5th to 4th and 4th to 3rd on occasion. The two dealers claim they cannot duplicate the issue and there's no CEL so there's nothing they can do. The shifting is also super slow between gears and regularly hangs in 4th until I let off the pedal for a good two or three seconds. All gear changes are slow.
Now the truck is exhibiting a new issue. When coming to a stop, a second after stopping the truck faintly jerks forward. Almost like the torque converter is not fully unlocked.
Ford 6.0L Power Stroke Diesel :: How To Get Oil Tube In Turbo
Still working on this E450. Now, I'm trying to get the turbo back on and I don't know how the heck to get the oil tube in.
There's so little room that I can't lift the turbo up. Just getting it in and out is a chore. I was able to pull the oil tube out with some difficulty when I was removing the turbo, but if it put it in first, the turbo won't go over it to get back in. If I leave it disconnected to get the turbo in, I have no way to reach under it to get the oil tube back in.
I only messed with it for a little while - it's physically difficult bending over inside the van to wrestle with it - and will go back at it first thing in the morning. I know there's gotta be a way, I've just never done this before.
Do I stick the tube in the turbo first, in the engine, or neither until I got the turbo in place?
Ford 6.0L Power Stroke Diesel :: Oil In Cold Side CAC Tube
What does that mean when there is a little oil in my cold side CAC tube?? It's just a little but it's even found it's way up into the intake elbow. Hopefully nothing too bad.
View 14 RepliesFord 6.0L Power Stroke Diesel :: CAC / Boost Tube Keeps Coming Off Under Power At Turbo Connection
Having this problem, what to do to correct it? There is no hole in the boot and this just started about a year ago. Does not do it all the time.
View 4 RepliesFord 6.0L Power Stroke Diesel :: Lost Turbo Again Even After New EBP Tube And Sensor?
Lost my turbo at idle early this week un plugged the ebp sensor which gave me a 10.7 default reading but got the turbo back at idle. Ok easy fix. Ordered a new ebp tube and sensor. Wired up the new pigtail and installed the new sensor and tube. Truck ran great all day. Now I goto leave tonight and I have the same problem.
So I unplug the ebp sensor and I have a default reading of only 6.5 now? I checked all my splice pigtail connections and everything looks fine still. What it could be this time?
Ford 6.0L Power Stroke Diesel :: How To Change Boot Or Hose On Egr Delete Tube
How to get the boot or hose off the egr delete tube without having to tear everything apart? mines leaking i have new hose to replace just not sure how to get the old one off...
View 7 RepliesFord 6.0L Power Stroke Diesel :: Small Leak At The Rubber Coupling Between EGR Tube And Oil Cooler
I am doing the usual upgrades on a 2005 F250. What started as a small leak at the rubber coupling between egr tube and oil cooler turned into doing everything else while motor is down this far.
I am curious what the difference in the upgraded oil cooler is? Well besides not prone to failing as early.