Ford 6.0L Power Stroke Diesel :: Coolant Leak / Drips Off The Power Steering Pump
I am having a heck of a time finding this coolant leak. It drips off the power steering pump. I replaced the upper radiator hose and the heater "y" hose that goes to the bottom of the Degas bottle. I recently replaced the lower radiator hose as well. So the truck runs normal. When the system is under pressure I do not see any leaks. But after the engine is completely cold it starts leaking a small puddle of coolant. Its appears to be coming from the power steering pump. But I am sure its something above or near it. This is on my 2005 Excursion with a 6.0. Can the water pump be going bad and leaking this direction. I would expect a water pump to leak straight down the middle of the engine. What to look for? The thermostat seal stays dry. but it has to be in that area. What is really messing with me is. When it is hot and pressured up It does not seem to leak. Only after it has been sitting for hours and cools off..........What the heck!
View 14 RepliesFord 6.0L Power Stroke Diesel :: Power Steering Pump Making A Loud Whining Sound
My power steering pump was making a loud whining sound. No problem, changed the pump. Now after the truck is started I will have no power steering or brake assist, give the truck a little gas and you can hear the power steering pump "start". I have tried every way to get the air out, or is that not the problem. I even lifted the front of the truck off the ground with a forklift and with the truck off turned the wheel about six times stop to stop. Fluid level looks good and has since adding after the change.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2004 E350 - Bad Vacuum Pump - Replacement?
I have a 2004 E350 6.0 with a bad vacuum pump. I tried looking on Youtube for a video on replacing the pump but no luck. Looking for a video or instructions on replacing the pump? It looks fairly easy but you need to be a snake to gain access to the pump bolts.
View 9 RepliesFord 6.0L Power Stroke Diesel :: Steering Stabilizer Removal / Replacement
Trying to replace my steering stabilizer and in the process I broke the nut close to the steering box. Would not budge so used a bar and well I broke it. Now I can't pop it out am I doing something wrong? Here are a few pics. I'm totally bummed nothing seems to be working for me.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - Power Steering Leaking Bad
So this '06 F350 is blowing fluid from the steering pump fitting when you move steering wheel to either side all the way(lock). Is the internal o-ring blown in the fitting? Do these have the teflon seal at the pump? Pretty new to the 6.0 scene. Got a new line ordered.
View 6 RepliesFord 6.7L Power Stroke Diesel :: Steering Wheel Position Sensor Replacement?
Replacing Steering Wheel position sensor. How hard of job is it?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2006 - EGR Valve Replacement?
From what I understand it should be dry where the valve goes. I would call it moist not wet but fairly moist. The top groove had the most wetness, the middle groove was dry and the bottom was nearly dry. Where do I go from here - the video I watched said to scrape out and vacuum - not dry enough.
[URL]
Ford 6.0L Power Stroke Diesel :: 2006 - 4WD Front Hub Bearing Replacement
I am looking for the known good replacements. Almost made the 200,000 mile mark before getting a groul out of the driver side. Ball joints seem good with very little movement.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Installation Of Washer Fluid Pump?
I am a new owner of a 2006 F 250 6.0.
I need to install a new washer fluid pump. My question is what is the best way to get the old one off and the new one on? Should I go from under the wheel well? Or is there another easier way to get to it? The truck didn't come with an owners Manuel and I cant find anything about how to do this.
Ford 6.0L Power Stroke Diesel :: 2006 F350 - Head Gasket Replacement
I'm going to be doing head gaskets on my 2006 F350 6.0. I know I need the head bolt tool and head lifting fixture. I have the tool to release the injector wiring plug from the head. Are there any other specialty tools I need? I saw in Hot Rod magazine a few months ago there was a new head gasket for the 6.0. Unfortunately I don't have the magazine anymore. I can't remember the brand of gasket. I know everyone in the past has said use OEM Ford head gaskets. Lastly, can I do the head gasket job and put studs in without pulling the cab or HVAC box?
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - A/C Condenser Leaking - Replacement?
Is the A/C condenser pretty simple to replace on the 2006 F350? Replaced the compressor but then noticed the condenser was leaking. Looks simple just wondering if there are any quirks to it.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Windshield Wiper Motor Replacement?
Looking for a video or directions as to how I replace a windshield wiper motor on a 2006 SD?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Overheating - Water Pump Impeller Slipping?
have a 2006 f250 with the 6.0 Powerstroke diesel started overheating yesterday the ECT and EOTcheck fine with the scangauge always ran with in 8 degree's of each other. Thought maybe water pump impeller may have been slipping so it is new with no change. Fan kicks on like it should. Heater works good so don't think it is a thermostat.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: Replace Power Steering Pump?
So, I'm replacing the Steering Box today and read an article that said you should replace the pump at the same time. what do you all think?? I have clear access to it now and they are not all that expensive?? Or are the ford one's bullet proof and leave it alone???
I don't have any leaks and it feels ok I guess..just pushing close to 200K on it.
Ford 7.3L Power Stroke (1999-2003) :: Power Steering Loss Intermittent - New Pump?
I have a 2000 Excursion. This weekend, I noticed some intermittent failure of the power steering where it seemed like the pump was not engaging and then would all of the sudden. Deciding to try to head off a failure, I got a reman unit from Oreilly and installed it this morning. It was fine when I tested, had good brakes and went locked to lock quietly without fuss. Let the house and within a mile, I lost steering and brake assist. I stopped and turned around, but what I am noticing is that at idle, I have no power steering, but when the RPM's are up, I do.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Power Steering Pump Camp Keeps Coming Off
My power steering pump camp keeps coming off. Almost like it's got too much pressure. I'm stumped as to why but it makes a mess whenever it comes off.
View 14 RepliesFord - Explorer :: 2003 - Power Steering Pump Removal / Replacement
I have a 2003 Ford Explorer with Power Steering problems. I have read and tried all the solutions I found here, except replacing the pump. Seems like it is the pump. Oil was burnt, I flushed twice. I checked the rack and lubed as identified in another post, same jumpy hard to steer issue. Anyway, now I am trying to remove the Pump. I have removed the reservoir and am trying to remove the pump. I have the top two bolts out, but cannot get to the bottom tow bolts. How do you access them? Do I need to remove the lower radiator hose, and / or the oil filter?
View 10 RepliesFord Escape / Hybrid :: 2005 - Power Steering Pump Replacement
We are a 2 Escape family. We have an '03 and an '05 - both 4WD and 3.0 V6. My college freshman son purchased the '05 this summer to get to and from his summer job. It has a little over 173K on the clock and it has a power steering leak, so I decided to try to tackle this one.
There is a fairly good video on YouTube on replacement of the power steering pump on an '03 - but apparently on the '05 Ford decided to relocate the pump from under the upper right engine mount to a lower location closer to the front bumper so the video is not of much use in this case.
I have searched the web and this site but cannot find any tips or instructions to replace the power steering pump on the '05. The Chilton Manual I have does not acknowledge the difference in the power steering pump location on the '05 and only provides the procedure for those Escapes where the pump is located under the upper engine mount.
I think I may be able to get better access by removing the inner fender plastic and perhaps the front bumper cover, but would really like to know the accepted procedure before I start tearing into this one.
One interesting bit of info regarding power steering fluid on these vehicles. Ford designed them to use automatic transmission fluid (Mercon) instead of power steering fluid. Initially, when I saw the leak, I thought it was a tranny line leak. Then I traced it to the front of the engine which is totally on the opposite side of the vehicle from the tranny lines.
Ford Aerostar :: Power Steering Fluid Leaking - Pump Replacement?
Proud owner here of a '96 3.0L RWD Aerostar Utility Van with about 138k miles, and leaking power steering fluid. At this point I'm replacing fluid from zero every time I have to drive it which is about once a week. I've located the leak and it seems to be coming from the pump/reservoir around the pressure hose. The hose is loose as in i can move it around a bit, but from what I've read, this is normal and the hose is supposed to be like that. I figure that at this mileage, with so much air going through the pump, all the crazy squealing and whining it does even when full, at this point it probably makes sense to replace the whole pump while I'm in there, as opposed to just doing the reservoir. Anyway, I'm planning to do this in a couple of weeks, and have some questions...
1) The pump - I've read on this forum that the best way to go on brand of the pump is Motorcraft.
2) Hoses - I'd like to replace the hoses coming out of the pump while I have this thing all taken apart, but I'm not exactly sure what parts to get. I know one is the pressure and one is the return, but there are variations of each based on the research I've done. The parts on the Napa site have different descriptions like "with switch port", "without switch port" "56in hose" "26in hose", and so on. Which ones I need, specifically the ones connecting directly to the pump? I havent been able to find anything in my research online, in Haynes, or Chiltons manuals.
3) Washers - Whether or not I replace the hoses, should I replace the washers at the connection point? Chilton's seems to recommend replacing them. Will they come with the new pump?
My local auto parts shop has the pulley remover/installer for me to rent so I've already got that squared away. I'm pretty sure I've covered all of my bases otherwise.