Ford 6.0L Power Stroke Diesel :: Knocking Sound / Heavy White Smoke
So I am owning my first diesel so I am still getting use to it. Shortly after I bought it, I had to make my 900 mile drive to work and it ran great. After being here for a week or so I noticed heavy white smoke bit thought it had to do with the -5- -10. And haven't seen the white smoke since the weather warmed up. Since then I have noticed a "knocking" sound that to me sounded like a rod that I didn't notice before. After reading through these forums, it sounds like I probably have a cracked injector. I have had no engine light or anything. So my question is, can an injector fail or be cracked without an engine light and can a code reader detect which one it is with no light on?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - White Smoke Coming Out Of Exhaust
Having trouble with 6.0 powerstoke white smoke out exhaust. We have installed egr delete and still have white smoke and water coming out of exhaust not as much as before. Took it back apart to see if we did anything wrong everything look ok. We did a compression test on all cylinders they check out ok.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2007 - No Crank / Heavy White Smoke Blowing Out Of Tail Pipe
I try to turn on my truck today and it will not crank. The day before I had change two injectors and I turned on the truck when two fill up my tank and I put a full bottle of injector cleaner with it. When I drove off, a few blocks down the truck turn off on me. I started to turn on the truck and every time I did it would blow heavy white smoke out the tail pipe and then it would shut off. I did this about 10 times until I decide to call a tow truck. The next day I empty out the fuel tank and fill it with diesel only. I tried to turn on the truck and it would not crank. I ended putting two new batteries and still the same result. What can this be ? 2007 6.0 Diesel ...
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Puffing Out White Smoke
I just bought a 2005 ford f250 6.0 diesel. Im used to gas engines but not to familiar with diesel yet. But my problems are it puffing out white smoke. I've just did an oil change with full synthetic motorcraft filter. I changed out the fuel filters. Ran some fuel cleaner put some oil additive (both diesel hot shot brand) . Drained out any water and cleaned out the pump. Took out the egr and cleaned it.
I just installed a coolant filter and drained out most of the ford gold and used something with CAT ECI rating. The smoke smells like unburnt fuel. I'm not losing any coolant. I bought a scan gauge. The fcim doesn't drop below 47 volts. The coolant and engine temp stay around the same. As weird as it sounds it won't smoke all the time. It will smoke really bad then it won't like nothing ever happened. Besides it being an injector failing or something along with fuel pressure I'm not sure.
Ford 6.0L Power Stroke Diesel :: 2007 F250 Blowing White Smoke After Oil Change
I just bought this 2007 F250 a 126K miles on it. Drove it about 1500 miles with no problems. I changed the coolant to Rotella ELC, installed Sinister Diesel Coolant and Oil Filter Bypass, and changed oil to Rotella 15W-40. 3 days after I did this it was in the mid 30's in the morning when I headed to town. It was blowing white smoke, so I stopped and smelled it. It did not smell sweet. I saw what looked liked diluted oil dripping from the exhaust. As I turned around it stopped. I revved it up and no smoke. I headed back into town(around 10 miles) no smoke. Drove home and no smoke. I was at home for about an hour and when I started the truck it was blowing white smoke.
I revved it up a couple times and it went away. I drove about 125 miles and no smoke. I let the truck sit about an hour and when I started it was blowing white smoke and no matter how much I revved the truck it did not go away. I went to work and the truck sat for 3 weeks. I just installed the blue spring kit. Started the truck and no smoke at first. Then, when it went to fast idle a little wisp of white smoke. As soon as I revved the truck up it got worse. Then it blew out what once again looked like diluted oil about 5 feet out the exhaust( I have a huge tractor weight sprayed with this). My first thought was maybe with the thicker oil I am getting some stiction so I am planning to change the oil to 5W-40 and add Hot Shot Secret tomorrow. But blowing the oil like substance out the exhaust has me concerned.
Ford 7.3L Power Stroke (1999-2003) :: F250 Started Running Bad Mid Drive / White Smoke With Diesel Smell
Just happened today right after I bought diesel. thought it may be water in fuel but after researching wondering if it is injector, etc. It starts every time knocks real bad sometimes for a minute, but clears up to idle ok. During idle no smoke, slightest acceleration however produces white smoke harder I accelerate more it plumes and it smells like diesel in the air.
Cannot get past 15 or so mph till switching into 2nd gear then 25mph max. Had to drive 4 miles like this I can say it cleared up and drove 1/2 mile until I had to stop at a traffic light then going from idle to acceleration again ran bad rest of way home another 2 miles.
A few years ago I did have a rough idle and accel. similar and it ended up being the broke pick-up/sending unit in tank (but of course that was when you get to around 1/4 tank of fuel and didn't run bad above that much fuel in tank), plus there was almost or more than a gallon of water in tank. I have done the mod for the fuel pickup with hoses, filter canister, etc. but wondered at first today if I had gotten bad gas or water in the tank again. Not sure how that much water got in the tank to begin with but that was bout 5 or 6 years ago.
Truck has over 200k miles and Ive had it for 11 years. In the morning will check the ICP sensor by unplugging look at fuel filter bowl, etc. A question I have is: Is water heavier than diesel, would it run thru my line first? thinking diesel is heavier than gas because of oil content....
Ford 7.3L Power Stroke (1999-2003) :: Smoke / White Haze Under Heavy Acceleration On Occasions
My truck 00' 7.3 255k is smoking white. It's not thick its more of a white haze. Sometimes it does it sometimes it doesn't. It has a 6637 intake, exhaust, and wicked wheel. No tuner or such. Im thinking either the turbo is going out or maybe a leaky injector? Just checked the turbo wheel and it has a little side to side play. On start up itll puff white then go away but then under heavy acceleration on occasion there is a haze of white then goes to haze of black. It also feels like the truck is lacking some power. There is no oil in the coolant or coolant in the oil. Not consuming oil or coolant. And there is no excessive pressure coming out of the oil fill.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2004 - White / Gray Smoke At Idle?
I have a 04 6.0l and all of a sudden it started dumping white/grey smoke at idle and when I drive it it goes to black then let off throttle and back to grey/white I had an up pipe leak at the y pipe I thought it might be an issue with that but I just got done fixing it and the problem still there so iam guessing it's either a sticky injector or the ficm but it starts up nice and does not knock around egr delete is don with all the goodies arp studs ect also the injectors have only 30k so it's hard to believe but iam just stumped haven't tested ficm yet and my tuner doesn't pick up any codes
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Low Or No Power / White Smoke
I bought a 2004 power stroke with 100k miles, ran well for 15k miles then started having low power for first few minutes to no power, regular oil changes and fuel filters at 5k, checked FICM 48v KOEO , 48v cranking, new batteries just in case. Oil pressure when cranking at 50% of gauge , even crank cycle will jump when trying to fire, no loss of coolant, block heater working, it did start a few a few times and blew white smoke until warm then full power but the last 2 times I did get it to start it ran for less than 1 minute and died could not restart.
Fresh fuel additive in both fuel and oil for stickshion, have read hundreds of posts but not seeing similar problems no codes. With key cycle 120 amp draw on passengers battery for approx 25 seconds 48 amp on right battery glow plugs good due to the amp draw? So I think my FICM is good, good oil pressure cranking, the oil pump should be good, ICP good? Because of gauge coming up? Everything I read says black smoke for EGR soot issues. Not sure where to look.
Ford 6.0L Power Stroke Diesel :: 2004 - Rough Idle - Blue / White Smoke?
2004 f250 6.0, 173k miles. I just had the head studs done and a new head due to a crack in one head, I got it back 3 days ago and she was running great. I towed my landscape trailer yesterday full of mulch and only went about 5 miles with the load, after the job driving to another one I noticed it sounded like it was missing at idle with a small amount of white smoke. Drove it home let it sit overnight, started it up this morning and a cloud of white/ blue smoke and a horrible rough idle. Smoke does not stop.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2004 Truck Blowing White Smoke Constantly While Running
My 04 PS was blowin white smoke constantly while running. I just towed a uHaul from Connecticut to Virginia Beach and had some coolant issues on the drive down (I was out of coolant on 95 in PA, added coolant and it made the rest of the drive no problem). I got here to Virginia and it was low on coolant again. I added coolant to it, and now I have some other issues. I had what looked like oil comin out the stacks onto the bed, so I pulled the turbo thinking it was seals. But the turbo was just rebuilt prior to me buying it with a wicked wheel in it. It still had stock EGR and it has 202K on it.
Checked and found EGR valve was wet. Ordered an EGR delete kit, and just finished installing it. Now with everything put back together, the truck doesn't want to start. It cranks but doesn't fire. I pulled the codes from my tuner and I got: P0403, P0405, P0683, and P2623. I know P0403 and P0405 are related to EGR but the others I'm at a loss on. The EGR delete kit I bought included the blank to remove the valve but what do I do with the plug that used to plug into it? Any way forward to get the truck back up and runnin again? This is my daily driver and not lookin to break the bank to get it goin again but I really need her to be reliable.
Ford 6.0L Power Stroke Diesel :: 2007 - Chugging White Smoke / Smelled Like Unburnt Diesel
2007 6.0 6 speed, 187,000 miles. The other day started truck, had been running about 20 minutes before. Started fine, go to drive, chugging white smoke, smelled like unburnt diesel, baby truck home, seemed to run ok at low rpm, truck warmed up and ran fine. But I also noticed turbo boost was acting funny. Truck ran fine next few days. Then this morning, started cold fine, started to drive it and same chugging white smoke, it quit by the time j got to the end of my driveway, but drove to work, it quit smoking, ran pretty smooth, but will not build any boost. Truck is bone stock except for exhaust, it's straight piped. Ok. So this eve I borrowed my dads edge cts, here's all the engine codes:
P0069
P0269
P0299
P2262
P2269
The last one is water in fuel, since it started this crap I did notice it was right after it came on in the dash. I'm trying to figure out where to start....
On another note. VGT duty shows 85% at idle ?
Ficm voltage is constant 48 volts
Newer batteries
Ford 6.0L Power Stroke Diesel :: 2004 F250 Just Died All Of A Sudden - Intermittent Power Loss
Ok I have an early 2004 F250. Recently changed out the #8 injector and then had to replace the ICP Sensor. Was running great then while driving down the road just died all of a sudden. Would start right back up with no issues. Continue driving and I am getting intermittent power loss. Also noticed that when it would lose power suddenly the glow plug light would come on.
Codes are P0102, P0113, P0272, and P1000.
P0102 Mass or Volume flow circuit low input
P0113 Intake Temp circuit High input
These are just soft codes not setting a light off. MAF is plugged in and I will check wiring here later after work but could this be causing my intermittent issues?
Ford 6.0L Power Stroke Diesel :: Died - Low Fuel Pressure - Blew White Smoke - Diesel Smell?
no change, changed stand pipe and dummy plug on driver side, no change and guess what? Now I am stuck on the side of the road waiting to give my last $100 to a tow truck! Engine is hydrolocked, fuel pressure is low, starts off at around 20 and works up to 54 with key on engine off, and that is as much as I know from the side of the road with out my AE. Blew white smoke also. Smelled of unburnt diesel. I think it's linked to my rough running issue. Maybe a bad injector? But every time I did the click test they all passed. Idk, I'm gonna remove the glow plugs and see which hole is loaded and with what. . .
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - White Smoke / Diesel Drip From Muffler / Poor MPG
I would like the hear what others have to say about the problems I'm having with my 2006 F-350 sd xlt 6.0 with 113,000 miles on it. It's being used as a tool truck mostly going from a shop on the property to close by buildings on the same property. In other words very short distances. Used occasionally to take a dump trailer to a close by dumping ground.
1. White smoke from exhaust. I've read this is most likely an ERG cooler that needs replacing. Any other possible causes? If I end up having to replace the cooler is there a stock cooler that is reliable or should I get the one by bullet proof?
2. Diesel is dripping from the muffler weep hole. Last full tank lasted only 60 miles. Could this be the oil cooler? Anything else? If so is the Ford replacement cooler OK or should I go with an upgraded cooler?
Ford 6.0L Power Stroke Diesel :: White Smoke From Exhaust?
yesterday I went out started my truck and white smoke started coming out my exhaust so I turned it off waited a bit started it back up let it run for a bit smoke went away drove it about 60 miles. Later that night it did the same thing but I was 2 gallons short on coolant drove it another 60 miles ran fine. Next morning decided to take it to a shop put more coolant in it drove maybe 20 miles to shop got there turned it off everything was fine never over heated once. So this shop is now telling me my trucks hydro locked and I steamed the EGR valve. And there telling me it's gonna be $8000 to fix it .
View 3 RepliesFord 6.0L Power Stroke Diesel :: Heavy Black Smoke When Taking Off From A Dead Stop
a little history here, about 2 years ago I got my first P401 so I changed the egr valve and it went away for a little while. Then I came back several months later and changed it again. along with the P401 I get heavy black smoke when taking off from a dead stop and after it gets a little speed it will run good. Here lately it seems I can only get 2 weeks to a month between cleaning the EGR valve.
Each time I clean it has a bb size piece of carbon stuck and is holding the valve open and there are several more under the EGR valve. each time I try to vacuum the carbon chunks out and clean everything as best I can. As of now I'm fed up with it and would like to do something to make it more reliable. would taking the intake off and cleaning completely and adding a EGR delete kit eliminate the carbon from building up?
Ford 6.0L Power Stroke Diesel :: White Smoke And Minimal Boost
Ok, took the sub for a spin around the block yesterday. Turbo was singing a tune when I left. white smoke and minimal boost on the way back. It is spinning, just not boosting very well. Stuck? Electrical problem? any pointers, or easy stuff yo check, before pulling the pump?
View 10 RepliesFord 6.0L Power Stroke Diesel :: White Smoke - How To Bullet Proof
I have the green light to bulletproof it. I just tore out the engine so she is on a stand now.
The whole backstory to this truck is one day a while back he was driving, noticed white smoke and instantly parked the truck at his house and fell on some hard times and couldn't get it fixed. The truck sat for some years and now was putting some life back into her.
I drained the oil and noticed right away the chocolate milk that was coming out of it, so right there I'm heading towards head gaskets.
What I am looking for is a list of the practical things to do to the engine while it is out on a stand. I am not looking for an extra 1000hp, just looking to bulletproof it so he won't have to worry about any other failures. I'm also looking for other maintenance items to change as well, maybe injector cups?