Ford 6.0L Power Stroke Diesel :: CEL Comes On For Code P2287 - Intermittent Injection Pressure Control Circuit
2004 Excursion 6.0L .... Recently after a 200 mile trip through the mountains running good, I get home and the next day it idles down the driveway at a high idle and after a few minutes seems to run better but within 5 miles the CEL comes on and throws P2287 - intermittent injection pressure control circuit. I cleared the code, ran around town again and the light came on again same code. I'm getting appropriate ICP-voltage and pressure readings. I took it home sat overnight and thought I would pull the ICP sensor.
I replaced the ICP sensor less than 6 months/5,000 miles ago. I also changed out the main engine harness at the same time. I looked at ICP sensor and it looks clean. Started the truck and tried the scientific wiggle test while running and monitoring ICP-voltage. Started at the sensor bending and wiggling back to FICM. No fluctuation in voltage. Ran the truck around town, 20 miles and no light. Yesterday we made the same 200 mile trip over the mountains, seemed to run strong. In town this morning within 5 miles the CEL is back on and the only code is P2287.
My Ford powertrain diagnostics manual doesn't have the P2287 code in it for troubleshooting. Should I go after the FICM, and how do U test that if so? I'm currently that 200 mile drive from home and don't want to damage anything more.
Ford 6.0L Power Stroke Diesel :: 2006 F250 Error Codes - Injector Control Pressure Sensor Circuit Intermittent
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
Ford 6.7L Power Stroke Diesel :: 2016 F250 - Check Engine Light - Code P0170
I just bought a 2016 F250 with the diesel and thought I'd share an early ownership experience. At about the 1300 mile mark the check engine light came on and other than the remote start not working the truck continued to run great. I pulled a P0170 code, Fuel Trim Bank 1. And since the truck was still running fine, I considered clearing the code and see if it would come back. But since it's under warranty I decided to bring it to the dealer. They checked it out and diagnosed a bad Fuel Rail Pressure (FRP) sensor. They swapped it out and it seems to be good to go (no more light). While I was in there I asked them to turn on the DPF percentage full screen which they did.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Code P0677 / #7 Glow Plug Circuit Module
06 6.0 F250 throwing code P0677 #7 glow plug circuit module. I don't think one bad plug would cause a no start, however coupled with too much oil possibly? Swapped my oil about 500 miles ago, I put in 20qts accidentally, drained off about 3-4 qts eyeballed, truck fired up and ran fine no smoke nothing. Yesterday morning I was leaving work and moved my truck from parking space to behind the bay at my fire station, I turned the engine off.
Loaded up my gear and turned the engine to the aux position and someone was talking to me so inlet it sit for a while in the auxiliary position. Went to crank no start, turned the key off then back on and it fired. Fast forward after 7 different starts throughout the day, I'm at dinner with my son we go to leave engine will not start at all, rolls and rolls and rolls nothing. Towed her home and scratching my head. Over filled oil with a bad plug cause no start??
Egr delete, new oil cooler, cat and muffler delete, upgraded Y turbo pipe. Also have an SCII throwing codes p0677 and p0401 egr code....
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Getting Codes Abut Transmission Range Sensor Circuit
I have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...
Ford 6.0L Power Stroke Diesel :: Engine Missing - Code P2077 - Cylinder 6 Injector Circuit High
I have for a week suspected my batteries were getting weak. just slower cranking is all. I took my truck in to have a viper security system installed and while he was doing his work he killed the batteries. I saw him hook up a battery charger and started the truck. He pulled it around to me and explained how the system worked and off i went. 5 miles down the road, on the thruway, I notice a miss and I'm down on power. FICM looked ok, 48V and it was charging, 13.8 I thought I would bring it to my shop and load test the batteries. On my way here, the check engine light comes on. At the shop, load tested them and they were weak. Installed 2 brand new batteries, started it up, no difference. Hooked up the scanner and pulled a code P2077 (cylinder 6 injector circuit high) Now what? I'm not sure where to go from here. I'm guessing either the FICM went bad or the #6 injector?
View 12 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Intermittent Crank / No Start
I have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 RepliesFord 6.0L Power Stroke Diesel :: Engine Light On And Code P2285 - Injector Control Pressure Sensor Circuit Low
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Codes P2285 And P2287 - ICP Circuit Low And Intermittent
The other day my 07 power troke threw codes p2285 and p2287- ICP circuit low and ICP circuit intermittent. The trucks idle was revving up or bouncing around every so often, not consistently.
I did a visual inspection of both the sensor and pigtail checking for oil but it looks to me like everything is clean and oil free (see pictures). When I unplugged the connector the trucks idol smoothed out and everything ran great!
My questions is what does this indicate? Does this mean my ICP sensor is bad, my pigtail is bad, or there is a short in the harness somewhere?
Ford 6.0L Power Stroke Diesel :: Cooling Fan Circuit 1 Or Code P0480
2006 F350 6.0 throwing code P0480 and I'm having a hard time figuring anything out pertaining to my truck. Trying to figure out what exactly it is and how to fix it myself.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Code P2623 For The ICP Circuit Open
Over the past weekend I had to replace all of the egr gaskets and seals, due to it failing smog. I removed all of the harnesses over the motor, intake manifold, turbo, and oil filter housing. I also replaced the oil/oil filter and also the fuel filters. The truck ran great before I decided to replace all of the seals. When I went to start the truck, it would just crank and not fire. One thing I noticed was that my wait to start light only stays on for a few seconds, where before it would stay on for a while. After cranking on it for a while I got a code P2623 for the ICP circuit open. I have tried unplugging the ICP sensor to see if it would start, but it just cranks over. The truck sounds like it wants to fire, but wont. Should I pull the ipr and ICP sensor?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Not Starting / Circuit Low For All 8 Injectors
2004 F250 6.0 and it's a no start. I have a snap on scanner and I did koeo test and it came up as inj circuit low for all 8 inj. I performed "the buzz test " and all inj click. The voltage on the scanner for the ficm is 52 and everything I read say that's more that enough. Where I should look?
View 1 RepliesFord 6.7L Power Stroke Diesel :: PO6A7 Code - VREF Circuit B Out Of Range
I have a po6a7 code boost gauge pegged at 40 code says vref circuit b out of range. What sensors run on circuit b and what could possibly be the problem my camshaft sensor is reading fault on scanner don't know if that has anything to do with it taking the truck to the dealer is not and option it's a 2011 6.7 with 75,000 miles....
View 1 RepliesFord 6.0L Power Stroke Diesel :: Code P0404 - EGR Circuit Range / Performance
I keep getting a problem code of P0404 - EGR Circuit Range/Performance. What it is and if its a serious issue?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Check Engine Light Came On - P1335 Code
My check engine light came on today and the code read P1335. What code is that?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Check Engine Light Code P21B0
CEL came on.. hooked up my cheap OBD/CAN scanner.. getting code P21B0..googled it and this is what i find: P21B0 - Reductant Level Sensor C Circuit High. What is this for? I've about had it with this truck..this having to replace a sensor every time I take it on a long trip stuff is getting ridiculous..2 EGT's, air charge cooler sensor, blower motor, and now this...
View 14 RepliesFord 6.0L Power Stroke Diesel :: Code P0262 - Cylinder 1 Injector Circuit High
Have a 2004 F350 which had problems starting cold and once started had bad throttle response until warm. It also had a shudder at cruising speed when going up a slight incline, would shudder until turbo kicked in.
Pulled codes which related to FICM and codes for all 8 injectors. 7 injector codes were circuit low, cylinder 1 high. Tested FICM voltage and sent FICM out for repair.
Installed rebuilt FICM, cleared codes, and hard start went away, but cruising shudder is still present.
Only existing code is P0262 for cylinder 1 injector circuit high. I'm assuming that cylinder 1 injector is bad -- are there any tests to confirm before I take it apart to replace it?
Ford 6.0L Power Stroke Diesel :: 2003 - Crank No Start - Code P2285 ICP Low Circuit
So yet another crank no start. Truck is an 03 55k miles The guy I bought the truck off of told me the turbo had been reconditioned about 1000 miles ago. Drove the truck another 1000 miles or so and now having issues. I went to start truck up and noticed it took awhile longer than normal to start up and when it did finally kick over, truck and no power at all. Would idle a bit rough sounded like no turbo spool at all when given throttle. Shut the truck off right and hooked up scangauge to it went to start it and nothing.
Did throw p2285 code ICP low circuit
Values read on scangauge are as follows:
FICM Main Power 48.0V
FICM Logic Power 10-8V
FICM sync is good
ICP Pressure 1540psi on crank
IPR duty cycle 14.8% Key on engine off/48.8% while cranking
At a bit of a loss as to where to look next, would really like to troubleshoot down to the right fix instead of just throwing parts at it. Have read after sitting the turbos tend to stick and need cleaned or replaced. After being cleaned only a few thousand miles could it be stuck again? Seems like I have spark, fuel, oil just acts like its not getting any air.
Ford 6.7L Power Stroke Diesel :: 2013 - CEL On With P206 Code / Fault Inj 6 Open Circuit?
On a family vacation in our 2013 6.7 pulling a 41ft trailer to the Seattle area from Alberta Canada. Made it to destination yesterday. Woke up this morning started truck and cel on. Bought a code reader at the local napa store and read P206 fault inj 6 open circuit. Any thoughts on driving the truck around with a inj fault? Thought I had read here some where that 6 was the regen cylinder.
View 14 Replies