Celica :: 7AFE Engine Timing Out With Rough Idles Every Now And Then
Well, a couple months ago my engine started making a noise. We located the issue to be a loose timing belt. We had it tightened, and the noise stopped, but since then it kind of acted like it was a little out of time with rough idles every now and then. This past week, I had driven my car out. I came to a 4-way stop and the car shut off on me. It would not immediately start back up so I pushed it to the side and waited a bit. It started up after sitting for a few minutes and cooling down. I got it back home and it stalled right as I was turning into my driveway (after the RPMs had lowered to idle).
A couple of days ago I set out to replace the timing belt as it seemed to me the timing was off ever since we tightened the belt and it eventually got worse, thus the stalling. I changed the timing belt, set the timing on the cams the way it shows to be set below:
I set the timing on the crankshaft pulley to the specifications found in this video:
Which is putting the crankshaft pulley on and turning it until it aligns with the '0' mark on the bottom timing cover. So I decide to start the car without anything else on to make sure its in time. It fires right up so I shut it off quickly and go about putting it all back together.
Once the car is completed, I attempt to start it again. It fires up, I back it up and it dies. It would not start back. I waited a few minutes and attempted to start it again, it started up so I pulled it back up to the same spot it was in and shut it off. Took the pieces off again, got it back to where I could line the timing up again. I again set the timing one more time to make sure. It was set correctly. I then tried starting the car again and this time it would not crank.
I gave up for now as its 30 degrees outside and I have been working on it non stop for 3 days to no avail.
Celica :: 1997 7afe 1.8 ST - P0340 Code For Camshaft Position Sensor
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesCelica :: 2000 GTS - TPS Replacement On Engine
Where is the TPS on the 2ZZGE engine? I bought an OE part from bap geon and i cant find it on the car to save my life.
View 2 RepliesCelica :: Speed Sensor Removal
I have removed the 12mm bolt and disconnected the speed sensor. The problem is that the speed sensor will not come out of the transmission. Is there a pin or something else that needs to be done to remove this speed sensor?
View 3 RepliesCelica :: 2000 - Left Lower Control Arm Removal
I am needing to replace a bent drivers side lower control arm, but it looks to me the 'front most' control arm to frame bolt is situated right next to the auto transmission! How can I snake this bolt out? Do I really have to raise the engine/tran up to clear this bolt on the control arm?
View 1 RepliesCelica :: 1987 - Oil Pan Replacement?
How do I replace the oil pan in my Celica? I have a crossmember directly below it.
View 2 RepliesCelica :: Ignition Switch Replacement Possible Without Key?
Is it possible to change the ignition switch without the key. Problem is my old key broke so im replacing the whole switch.
View 1 RepliesPrius C :: Radiator Cover Removal For Horn Replacement?
Just received a set of new horn kit from piaa.. Now wonder how can I remove the radiator cover properly for the horn replacement.. Or do I have to remove the bumper?
View 2 RepliesGolf VI R :: 2012 - LED Fog Light DRLs Replacement / Removal
So looking to replace the passenger side front LED fog light assembly as the one that's currently on the car has a bad seal or something and lets water in. I have a new LED assembly but I'm lost with how exactly I'm to get the new part in. I've searched for diagrams regarding the replacement of the part and found one diagram that said the front bumper had to be completely removed from the car but I find that a bit hard to believe... (Then again its euro so maybe it's not hard to believe). Can the lower intake grill on the passenger side not just be pulled out or something? 2012 Golf R MK6....
View 2 RepliesCamry :: 2005 - Ignition Cylinder Removal / Replacement
How do I get to the screws behind the ignition cylinder (where the key goes) to remove it and replace with a new one? Do i use a short screwdriver?
View 1 RepliesPassat (B5) :: Right Side Drive Shaft Removal / Replacement
From what I've read, the procedure for removing and replacing the drive shaft involves pulling the upper ball joints and tie rod end from the steering knuckle--is it possible to put a floor jack below the lower arm (the load runs to the spring through the lower arm) and undo the lower ball joint to get the clearance required to remove the shaft?
View 9 RepliesCelica :: 1995 GT - Timing Belt And Oil Seal Replacement
Looking for the proper instructions in replacing timing belt and oil seal I have done this on a Honda accord before but I need to know how to properly align everything so I can do it right the first time.
View 2 RepliesCelica :: 1990 - Speedo Is Not Working After Clutch Replacement
I just replaced my clutch and now my speedo is not working ? It did work for about a day after the job, but now it just reads 0 all the time... would low fluid cause that ?? I put two quarts in after putting the trans back ....
View 4 RepliesPrius (2004-09) :: Airbag Replacement And Seat Belts Removal
I have an '05 package 2 and I am replacing the steering wheel. I found that I need to disconnect the battery to replace the airbag, I also read that it is a good idea to remove the SRS relay. Which one is the relay under the hood? additionally I am trying to remove the seatbelts to clean them how do you remove the paneling without breaking the plastic?
View 1 RepliesPrius (2010-12) :: Front Windshield Wipers Removal / Replacement
I have a 2012 Prius. How do I remove the front windshield wipers so that I can replace them?
View 2 RepliesFord Ranger / B-Series :: Fuel Filter Removal / Replacement
I know where the filter is, i know how to bleed off the pressure. Im wondering if those clips are easy to slide off to remove the filter from the lines?
View 7 RepliesFord F-150 (2004-2008) :: Spark Plug Removal / Replacement
I just picked up a 05 F150 lariat 5.4 2wd with a 177k on it. What the chances of these plugs coming out with out breaking? Any tips tricks to getting them out? Should I put motorcraft plugs back in it ?
View 6 RepliesFord F-150 - 1997-2003 :: Torque Converter Removal / Replacement
I have a 97 F-150 Supercab XLT, 4X4, 4.6L W, 4r70W with electronic Overdrive, manual shift transfer case. I need to remove and replace the Torque Converter. My question is: Would it be easier to drop the transmission and transfer case or pull the engine loose and move it forward to get at the torque converter?
It is shifting in and out of overdrive to third, and then back into OD, and back into third erratically and for no apparent reason. It is also slipping intermittently in first from a dead stop and locking all at once, shifts hard then. When I first drive it the OD light does not flash and the OD off switch works, once it warms up good it starts shifting erratically and the OD off switch starts flashing, then the off switch does not work.
I did not get any codes returned on autozones little scanner and am taking it to the ford dealer for a full scan today to see if there might be any other damage or cause for this problem. The problems started when I blew a hose to the trans cooler in the radiator and lost fluid. I didn't notice the blown hose until it started slipping and pulled over, replaced the hose and fluid. Had problems ever since. I have cleaned the MAF sensor and replaced the ABS sensor in the differential so far.
Celica :: 1998 Toyota Front And Rear Strut Replacement
Any good video/instructions/tips on replacing the front and rear struts on a 1998 Toyota Celica?
View 2 Replies