Toyota :: Knocking Noise After Strut Assembly Replacement
I ran over a rather large pot hole while driving home in the middle of the night. It destroyed my tire and tire sidewall and soon after the strut started to make a knocking noise while going over bumps. I replaced both front strut assemblies with Monroe Quick Struts (photo attached). After the install, the noise was gone and everything seemed good so I gave the car to my wife. After several months, I decided to drive the car to see if everything was still OK and it wasn't. The knocking noise on the driver front strut came back.
I took the car back to my mechanic and he said that he thinks the strut assembly was defective and that I should get a replacement since it was under warranty. I would just pay labor again for him to change it. Something seemed off by the conversation, so I decided to take the car to another mechanic for a second opinion, but before I do that I want to pose this question here. What could be the problem? Why did the knocking noise come back?
I've attached more photos. You will see two photos of the tops of the strut assemblies from under the hood. The first top photo is of the passenger left strut that is good (with the wheels straight). The second top photo is of the problematic driver front strut. You can see the top is slanted left with the wheels straight. The rest of the photos are from around the driver side wheel.
I did complete a wheel alignment after the install and the car pulls left when the steering wheel is straight after the alignment.
More information about the Monroe Quick Strut: [URL] .....
Honda - Cr-v :: Front Shock Strut Assembly Replacement
Took my 2004 Honda CRV 2W Drive to my local dealer for the 90K maintenance. There they recommended for me to replace the front shocks strut assembly--not quite remembering the reason but they told me that it needs to get done. Before I get the work done, I am trying to find as much info on what next steps to take.
View 10 RepliesFord F-150 (2004-2008) :: Front Strut Replacement
I've just begun to replace my front struts (Monroe quick strut pre-assembled). The thing is, the top bearing plate bolts and the lower mounting point are out of alignment by 90 degrees. The included directions say they can be rotated but gives no procedure and they do not just "turn" easily obviously. How to rotate them to fit??
View 3 RepliesCamry :: 2004 LE - Dull Clunk Noise In Rear End After Strut Replacement
I just replaced all 4 struts on my 04 Camry. The car has 87,000 on it. I went with the Monroe OESpectrum struts and new strut mounts (Monroe). Springs looked fine, the rubber spring seats were fine as well and the bellows, so reused those items.
I now have a noise in the rear end that I did not have before. It sounds like it is coming from the lower part of the car and is not metal sounding. It is a very dull clunk when going over bumps in the road and is coming from both sides.
I replaced the sway bar bushings a couple years ago. I checked those and there is no play and appear to be fine. Also checked the sway bar links and they seem fine to me, but not sure what makes those bad. Torqued what I could. Used an electric impact wrench on the strut nuts and could not torque that because the rod spins.
I am taking it in on Monday for an alignment and to have the shop see if they can figure out the noise. Is it possible that the new parts could be binding and the alignment may take care of it? I have doubled checked my work and everything appears to be on correct.
Toyota - Corolla :: 2006 - Right Front Strut Leaking Oil?
I have a 2006 Toyota Corolla with 183,000 miles on it. My mechanic noticed that the right front strut was leaking oil. In addition to replacing it recommended getting a strut mount installed as well. Is this an necessary component at the age of my car or can just replacing the strut do the trick?
View 14 RepliesToyota - Corolla :: Front Strut Fell Out Of Mounting Hub - Safe To Drive?
Is my car relavtively safe to drive?
I just took my car (1984 Toy Corolla DX) to the mechanic and the right front strut fell from its mount. The mechanic lowered the vehicle and reinserted the strut. I drove it home, ever-so-cautiously. Is the car safe to drive for emergency trips (pay bills, buy groceries) until I can get it fixed next month?
Toyota - Celica :: 1998 GT Convertible Suddenly Lost Fifth Gear
I have a 98 Celica GT convertible that had suddenly lost fifth gear, and what I mean by loosing fifth gear is not that it pops out of fifth or that it will not go into fifth, the gear shift lever goes into the fifth gear position just fine and stays in that position, yet the car responds as if it is in neutral. This is what happened while driving home recently. The first time this happened was within a week or so of having my clutch replaced, so I took it back to the mechanic that replaced my clutch.
Upon investigation he found that the nut that holds fifth gear in was loose. He tightened this nut and it fixed the problem for awhile. This was now over two years ago, and to make a long story short, I eventually ended up having to replace that transmission with another used transmission from a salvage yard. The current transmission has been in the vehicle just over a year and a half with no problems until now. I am getting this same problem again, with no fifth gear.
Celica :: 1993 Toyota GT - Wheel Bearing / Upper Tower Mount Replacement
I have a 1993 Toyota Celica GT I removed the strut tower to replace the upper tower mount and replaced the wheel bearing. my problem is that when i torque the axle nut tight the tire can be moved by pushing it up or down.
View 2 RepliesCamry :: Strut And Spring Assembly Replacement On 2007 LE
Looking to replace my strut and spring assembly on my 2007 Camry LE with 130,000 miles. What is the best China units out there. The list is many Prime Choice, Detriot Axle, Unity, FCS, AST, Sensen, ect.... Maybe they all are made at the same factory. FYI Monroe and Gabriel could be made in China. KYB complete units are assembled in USA, I called them up.
View 13 RepliesCamry :: Steering Wheel Crooked After Strut Replacement
So I changed the front struts, springs, mounts, bearings, etc with factory Toyota parts. The car is a 2007 Camry LE 4 cyl with over 200k miles. While the car does not pull to one side, the steering wheel is now at roughly the 2 o'clock position for the car to be driving straight. Nothing else was changed, replaced, or modified. I do notice the car sits much higher now than it did before (old struts leaked oil and needed to be changed).
View 8 RepliesPrius (2004-09) :: Clunking Noises After Strut Replacement
I had my friend of mine who is a mechanic change my struts out this weekend. I had clunking noises from the right strut Toyota and also a tire place said I needed new struts. So I got them replaced now both sides are clunking see the YouTube video.
View 7 RepliesCamry :: Weird Noise Coming After Strut Replacement
I recently replaced my factory struts with KYB's all in one solution. I also did the craft felt mod that HardTop suggested. Ever since they have been replaced I'm getting a weird noise. When I turn the steering wheel in either direction it makes a rubbing sound that is very audible. The vehicle drives fine, and the struts ride really well. However, the noise is a touch annoying.
View 8 RepliesPrius (2004-09) :: ABS Light Came On When Car Started After Strut Replacement
I replaced my front struts today and afterward the ABS and "(!)" light came on as soon as I turned on the car. I checked the speed sensor lines and they all look okay so I didn't damaged them in the process. The car brakes quite soft but still works and the regenerative braking still works. The mechanic pulled the following codes: C1300 and C1319. I went ahead and reset the ABS light by crossing pin 4 and 13 on the OBD2 connector technique. That reset the lights, and the brake also works as normal as well. After driving around a bit, turned off the car, then turned it back on the lights came back on again.
View 6 RepliesCamry :: Knock / Clunk When Going Over Bumps At Low Speed - Strut Replacement
I Spent the day yesterday replacing all four struts on my '07 LE. I went with KYB, the installation went well (so I assumed). I put everything back together exactly as I took it down. Outside of the struts alone, I reused all other parts as everything seemed to be in good order.
Test drive: I seem to have a knock/clunk when going over bumps/pot holes at low speed (<35 and especially <15mph). At highway speeds (65+), I do not hear it at all, even if I hit something. I had a friend ride in the back and confirm that it was coming from the driver's side (left) rear.
Took everything back out and inspected, I noticed that the strut mount has a flange that runs to the flat side of the strut rod that looked a little worn, so decided to go buy a new strut mount (Monroe garbage, only thing available locally). I did notice the Monroe strut mount didn't have that flange the OEM one had, it is just a circle...I didn't know if that mattered. I Put in new strut mount on, same sounds in the same conditions. I want the clunk to go away.
Avalon 2005-12 :: 2008 - Torque Strut Mount Replacement
I have to replace the torque strut mount in my 2008 Avalon XLS V6. I can't find the torque specs for the two bolts in my Haynes manual or at any online sites. Also, should I use either threadlocker or anti-seize on them?
View 1 RepliesCorolla :: Toyota Matrix XR 2010 Front Bumper Replacement
I have a Matrix XR 2010 with front bumper sporty look . I like to change the front bumper to regular bumper and the reason is that for the last two winter seasons I have broken the spoilers and basically wreck the bumper.
View 2 RepliesToyota - Camry :: 1998 V6 Front End Rattle When Going Over Bumps At Speeds 20 - 35
My 1998 V6 Camry has rattle on right front and now starting on left too. Bad shocks were replaced and still rattles going over bumps at speeds 20-35. Don't notice on freeway. Car drives fine, no pulling or other problems just irritating noise at slower speeds. Two different mechanics say the Strut mount plate is loose. Could not find any other problems? Is it okay to leave the mount plates in place? Mechanics say other than annoying there isn't a problem.
View 5 RepliesCamry :: 2009 Toyota - Front Brakes Clunking / Knocking After Replacement
I changed the front brake rotors & pads on my wife's 2009 Toyota Camry & everything seems fine except when doing sudden or slightly hard stops it seems to do a clunk/knock type sound from the front brakes. It also only does it sometimes not every hard/sudden stop.
One thing that comes to mind is that when I went to tighten one of the guide pin bolts it was a real pain, the big bolt that the screw threads into kept spinning making it hard to tighten the bolt into & none of the others did this. I thought I tightened it down but possibly not?
Toyota - Sienna :: 1998 - Noise In Front After Suspension - Steering Overhaul
So I started a "quick" strut job on my mothers 98 Toyota Sienna last weekend, after many complaints about a rattling noise on the passenger side while driving on semi smooth roads. I got in and found that the CV boots were gone, and there wasn't much grease in the boots, all the ball joints were loose, and the wheel bearings were starting to grind. So since the car is at 225,000 I ordered the parts and took Friday off. I started the job, and also found out that the inner tie rod boot was completely full of ATF(This cars power steering fluid). There was a massive 2 day struggle with the CV axle being rusted in the motor mount bracket. But I finally got it all replaced and back together.
So all told I ended up replacing the following parts; Power Rack, Inner Tie Rods, Outer Tie Rod Ends, Rear Lower Passenger motor mount, Strut Mount, Lower Ball Joints, CV axles, Wheel Bearings, Lower Struts, Upper Strut Mount, Fuel Filter, Brake Pads, Brake Hardware, Oil Filter, and the Oil. I got it all back together and just finished the test drive ONLY FOR THE NOISE TO STILL BE THERE!!!!! What did I miss? What could it be? Is there something simple I could have done wrong to continued to have the rattling noise? Also the steering wheel is off 20 degrees to the left, I could handle that, but its not my car and my mother says it needs to be fixed... PS I am planning on taking it in for an alignment, but it does drive straight down the road as it is.