Ford F-150 (2004-2008) :: Tie Rod End Torque Specs?
Just doing the bro in law's tie rod ends and we are wondering what torque we should be putting on the castle nuts? They are greasable Moogs...
View 2 RepliesGolf IV R32 :: Specs For Bearing Caps And Order To Torque Them?
I need the torque specs for the bearing caps and the order to torque them. Can't find the pdf file for the bentley. Looking for a link to the bentley..
View 24 RepliesLexus RX 2010-15 :: Torque Specs For The Caliper Bracket Bolt?
2011 Lexus RX350 ... What are the Torque specs for the caliper bracket bolts (front and rear caliper brackets) a pdf will be great
View 1 RepliesGolf IV R32 :: Valve Cover And Intake Manifold Torque Specs
I have to replace the valve cover gasket this weekend.
View 5 RepliesFord F-150 - 1997-2003 :: 1999 - Driveshaft Bolt Torque Specs
What the torque spec is for the driveshaft to rear differential flange mounting bolts on the 99 F150 4x4 supercab?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Torque Specs For Tie Rods?
What are the torque specs for tie rods for a 4x4.
View 4 RepliesFord F-150 - 1997-2003 :: 1999 - Front Hub Assembly Torque Specs?
Tell me the torque specs for the various attaching nuts of the front hub assembly for the 99 F150 4x4 5.4L (large nut on the spindle, mounting bolts to back of spindle, etc if any) ? I will need them to put everything back together after checking the tone ring for my ABS problem.
View 1 RepliesCamry 2012+ :: 2014 SE - Oil Filter And Drain Plug Torque
New 2014 SE 2.5L owner here. Gonna Amsoil my rig when it hits 5K. I bought a filter wrench and drain plug gaskets online. What's the torque spec. on the filter housing and drain plug?
View 7 RepliesFord Super Duty (1999-2016) :: 2012 F350 6.7l - EGR System Torque Specs
Replacing EGR cooler/ EGR valve. Are there torque specs going back together with the EGR system? or is there a forum that has all the torque specs id need to complete the job.
View 4 RepliesFord 6.7L Power Stroke Diesel :: Torque Specs For Front And Back Rancho 9000XL?
What are the torque specs for front and back rancho 9000xl? Really want to know the front top spec with the rubber bushings that squish flat the most.The rest ill make tight.
View 14 RepliesFord F-150 (2009-2014) :: 2012 - Mounting New Shocks - Torque Specs For Upper And Lower Bolts?
Mounting the shock with the boot up or down? I know it doesn't matter according to Bilstein but one way has to be better than the other.
Second. What are the torque specs for the upper and lower bolts? I know the lower front is around 350lbs but haven't found anything for the rest. found out the rear bolts are torqued to 66lb.
Third. The front shocks didn't come with a boot to protect the shaft. Is one needed when the shock is installed?
Truck is a 2012 F150 FX4.
Ford 7.3L Power Stroke (1999-2003) :: Water Pump Lower Elbow Bolts Torque Specs
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.
Ford Super Duty (1999-2016) :: 2005 - Torque Specs For Crankshaft / Cylinder Heads And Camshafts?
What are the torque specs for the crankshaft,cylinder heads and camshafts for a 2005 f550 v10 6.8?
View 2 RepliesFord Exhaust :: Torque Specs On Exhaust System?
Just put on a 4" MBRP turbo back system. What torgue should I tighten the clamp bolts?
View 2 RepliesPassat (B6) :: Torque Settings For Oil Drain Plug?
What are the correct torque settings for oil drain plug, oil filter and spark plugs on a 2.0 FSI engine?
View 3 RepliesCamry :: 2007 SE V6 - Passenger Side Exhaust Hanger Bolt Specs?
Specs for the two bolts/washers for the passenger side (only) exhaust hanger? I'm referring There one hanger on the passenger side only w/ two captive threads in the subframe.
View 3 RepliesPrius Plug-in 2012-15 :: Won't Charge - No Fault Codes On Torque
Edit (3/2/13): Problem identified. The timer was incorrectly and inadvertently set, so charging wouldn't start. See this post below.
Three times in the past two weeks, my PiP has refused to take a charge. It happened twice on Chargepoint chargers. The second time, I plugged in and the charger displayed "Vehicle refused charge" or something similar. Tried 10 times with the same result. Then it charged fine at home, and on 240v the next day.
This morning, it won't charge at home on 110. Plug in, the brick clicks, it draws about 200 ma for a couple of seconds, and then zero. Totally repeatable.
No fault codes on Torque. The dealer had it earlier this week and couldn't make it happen or see any fault codes either. The first time it happened the charging cable was off the ground, so I suspected a bent pin, but they all look fine.
Corolla / Matrix 2009-13 :: U341e Transmission Drain Plug Torque?
The transmission drain plug torque on a 2011 Corolla s, u341e transmission.
I have heard 36ft lbs, I just feel like that is a lot and want to confirm. Any horror stories on snapping these plugs? I'm planning to get new crush washers.
Any experience with just using a fluid extractor to do multiple drain and fills from the dipstick? I've heard the tubing can sometimes melt/break off, but was considering this route to not have to deal with snapping a drain plug.
Tried searching, tried checking my hanyes manual and my factory service manual I have in pdf, neither lists a torque, or at least that I can find.
Corolla / Matrix 2009-13 :: ATF Drain Plug Size And Torque Spec
What is the ATF drain plug size and its torque spec?
View 3 Replies