Lexus RX 2004-09 :: 07 - Serpentine Belt Tensioner Pulley Making Noise
My tensioner pulley is making noise.I replaced the rear idler pulley (can't get to the front one), but still have the noise. Mention a DIY for replacing the tensioner pulley bearing. A part number for the bearing?
View 2 RepliesSanta FE SM (2001-06) :: Engine Making Loud Ticking Noise - Crank Pulley Gone
Oh where do I start. 2003 Santa Fe, V6 Auto, FWD.
The engine has been making a loud ticking noise lately, starting right after an oil change it seemed. It actually sounded a lot like a stuck lifter, so I had an engine flush done, but this did not remedy the problem. Popping the hood one day it was particularly noisy, I noticed that it sounded like it was coming from the serpentine belt tensioner (or there abouts).
Anyway, tonight, *something* finally gave. All of a sudden I heard a squealing noise, then smelled burning rubber, and my battery light came on, and I lost my power steering. I figured that the tensioner finally gave out.
I turned off the vehicle to see what I could see. A bit of melted S-belt was it. I restarted it, and the belt was turning fine again, but while it was idling, I noticed that the crank pulley was shifting in and out now and then. When it moved inward, the S-belt shifted in as well, and started to rub on the timing cover, wearing a hole right through it! Have a look at the attached photo, showing the grove worn right through.
So I'm assuming that my tensioner was fine, and it was my crank pulley all a long. I'm figuring that 3 thing will need replacing:
1. Crank Pulley (the source of the problem)
2. Serpentine Belt (since it's probably half melted)
3. Timing Cover (can't see that water getting in there would be good)
Does this sound accurate?
Golf IV / Jetta IV :: 2.0 AC Pulley Noise / Bearing Replacement?
Wondering how I would take the A/C pulley off to change the bearing or fix the chirp squeal it is making.
I have spun this pulley by hand and it is the culprit making the noise.
It has an inner pulley and an outer pulley(belt pulley). Both spin freely and are not bound up. Just want the terrible noise to go away.
Camry :: Idler Pulley Replacement On Serpentine Belt Tensioner
2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.
View 2 RepliesCamry :: Nut That Hold Pulley On Alternator Fallen Off - Serpentine Belt Will Not Stay On
The nut that holds the pulley in place on the alternator has fallen off, causing the pulley to become loose and now the serpentine belt will not stay on. What is the size and thread type for the nut that I need to replace?
Alternator Pulley Nut for 2004 Camry 4cyl
Honda - Odyssey :: Engine Started Making Clicking Noise Upon Acceleration - Timing Belt Replacement?
I have a 2006 Honda Odyssey. I got the timing belt replaced two weeks ago.Last week the engine started making a quiet clicking noise upon acceleration. The clicking noise happens intermittently not continuously. Then last night the yellow engine light came on. Questions: What does the yellow engine light mean? Is the engine light related to the timing belt work that was done? Would the clicking noise be connected to the timing belt work?
View 3 RepliesLexus RX 2004-09 :: Chirping Noise Coming From Belt Tensioner Or Idler Pulley
So from reading around a lot, it seems like the chirping is from the belt tensioner or idler pulley. That said, I've not been able to find anything definitive. I tried to do the water bottle squirt test (from Gates' youtube video) and either I did it wrong or the chirp did not go away implying the issue is not the belt. While I was looking in, I could see the tensioner shaking some.
If my tensioner should not be moving, do I just need the pulley or the pulley and the mount?
- Pulley [URL] ....
- Pulley and mount [URL] ....
Also, if the above items will fix the chirp, which brand would be best?
2007 RX 350, 113K.
Chirping gets worse as it heats up. Seems to happen independent of ambient temperature. Purchased a year ago so unsure of the history of part changes.
Accent MC (2006-11) :: Belt Squeaks - Tight Pulley Bolt On Alternator To Add Tension To Belt?
One of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 RepliesCamry :: Squeaking / Dry Bearing Noise On Cold Engine Start
My Camry 2grfe now has almost 60k miles and it started making a squeaking/dry bearing noise but it goes away after about 2 minutes of running. I was going to replace the serpentine belt when I get a chance, its a tensioner or a pulley bearing? Can the bearings in the tensioner or pulleys be replaced instead?
View 4 RepliesSuzuki - Aerio :: 2005 - Vibration / Tensioner Pulley Making A Lot Of Noise
i just recently went to a mechanic check out my wife's car cause it was vibrating really bad, and a pulley was making a lot of noise... they told me that the alternator bearings were shot, and i needed 4 motor mounts, long story short i changed the alternator.... it wasn't the problem... had them check it again, they said power steering.... i didn't want to waist a couple hours of work again, i checked it myself like i should have done in the first place... and found out it was the tensioner pulley.... so can i get any pointers on how to change the tensioner pulley, cause i tried and i lacked about 1/4" of space to get the bolt out... do i need to drop the engine or raise it? if so how.. 2005 suzuki aerio 2.3L .....
View 6 RepliesFord Super Duty (1999-2016) :: 2006 - Serpentine Belt - How To Route The Belt Around Tensioner Pulley
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
Prius (2004-09) :: Noise From Belt Tensioner Bearing?
During the 120000km (75000mi) service my Toyota local service said I have a noisy Prius and that the sound is from the belt tensioner bearing.
As I bought it used and always heard the same sound. I've made a video ....
Golf IV R32 :: Front Right Wheel Bearing Is Making Noise
So my front right Wheel bearing is making noise and its a used Knuckle so its w/e. Guess ill use tonight to do all my bushings and fluids n stuff.
View 6 RepliesFord - Explorer :: 2000 - Making Bearing Noise?
2000 Explorer making what I would call a bearing humm. I have replaced both front wheel bearings over the past year. When I jack up the front and check for play everything is tight, I don't get any noise by spinning the tires. While driving I put the tranny in neutral and still get the hummm sound, so I don't think it is the tranny.
The sound definitely changes with the speed of the car. Turning the wheel or engaging the transfer case do not change the sound. I have had my son crawl around the car while I'm driving and he said the sound is not coming from the back, for sure the front but can't tell if it is specific to one side of the other.
Where do I go from here? This is my daughters daily driver and its been a great car, 148000 miles and no issues at all so far. I would like to figure it out so I can feel good about her driving the car.
Chevrolet - Blazer :: Wheel Bearing Making Noise After Tire Replacement
Immediately after I had four new tires installed on a 2000 Blazer 4wd, the front wheel bearings started making noise. At the time I thought the noise was from the new tires. A few thousand miles later my mechanic told me I needed two reman hub assemblies (sealed bearings) for ~$350 apiece plus labor.
Is there anything that the tire shop (independent not chain) could have done (accidentally or otherwise) to damage the bearings during the tire installation? I have to get 4 tires for my 93 Chevrolet Caprice and don't wish to repeat the experience.
Whoops, forgot to mention this happened at 56k miles when the truck was five years old. Is it possible that the bearings were borderline and the process of mounting the wheels put them over the edge? For instance, someone being a little over enthusiastic with an impact wrench.
Ford 6.7L Power Stroke Diesel :: Wheel Bearing Gone Out - Making Noise?
Wheel bearing go out? My left front just starting making noise and when turned by hand you can hear the bearings are shot. Called around this morning and with my luck its on back order and the entire hub has to be replaced since the bearing is built into the hub.
Anyways, I was wondering replacing this unit themselves and how long it took to complete? I was going to let Ford do the work but I figured I have never done a job like this and wanted to give it a try and looking at some Youtube videos on older vehicles it did not look that difficult.
If I find that its not difficult I will tackle the other side as well since I figure it is probably not long before that side is gone also and I would not want that to fail while I am out towing somewhere.
Camry :: Engine Noise - Bad Serpentine Belt Tensioner Is Seized On
After finally identifying a bad serpentine belt tensioner for being the the culprit for my engine noises, my mechanic said that the 'thru-bolt' is siezed. Since the replacement job was at my budget limit he said he doesnt want to get into it in fear that he has to brake the bolt and drill it out (requiring 2-3x more labor cost according to him).
If this is the case, and the 'thru-bolt' is seized, is this in any way something I can make a an effort to tackle? I have a jack and jack stands, and plenty of time.
Corolla / Matrix 2009-13 :: Throw Out Bearing Making Faint Chirping Noise
My throw out bearing makes a faint chirping noise since I bought the car, but now that the weather has been in teens, it seems to be louder.
I was wondering if it is possible to grease the throw out bearing or something without dropping the transmission.
Ford F-150 - 1997-2003 :: AC / Clutch Bearing Making Noise - New Starter And Still Won't Start
I have a 2000 F150 XLT 5.4L truck. I noticed the AC went out about a month ago and since then I could hear the AC/Clutch bearing making noise. Well I went to start it the other day after eating dinner out and it wouldn't start. It sounds like it wants to start but it just doesn't have enough umph. I replaced the starter and charged the battery up to 100 percent. It still won't start.
If I take the belt off it will start and I checked the AC/Clutch and I can move it with my bear hands. I tried disconnecting the AC/Clutch fuse and relay but that didn't work. Is it possible that the Clutch is freezing up when I try to start it?