Lexus RX 2004-09 :: Chirping Noise Coming From Belt Tensioner Or Idler Pulley
So from reading around a lot, it seems like the chirping is from the belt tensioner or idler pulley. That said, I've not been able to find anything definitive. I tried to do the water bottle squirt test (from Gates' youtube video) and either I did it wrong or the chirp did not go away implying the issue is not the belt. While I was looking in, I could see the tensioner shaking some.
If my tensioner should not be moving, do I just need the pulley or the pulley and the mount?
- Pulley [URL] ....
- Pulley and mount [URL] ....
Also, if the above items will fix the chirp, which brand would be best?
2007 RX 350, 113K.
Chirping gets worse as it heats up. Seems to happen independent of ambient temperature. Purchased a year ago so unsure of the history of part changes.
Ford Super Duty (1999-2016) :: 2006 - Serpentine Belt - How To Route The Belt Around Tensioner Pulley
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
Lexus RX 2004-09 :: 07 - Serpentine Belt Tensioner Pulley Making Noise
My tensioner pulley is making noise.I replaced the rear idler pulley (can't get to the front one), but still have the noise. Mention a DIY for replacing the tensioner pulley bearing. A part number for the bearing?
View 2 RepliesSanta FE SM (2001-06) :: Idler Tensioner Pulley Seized
I have a 2003 Santa Fe 2.4. Couple days ago my idler tensioner pulley or whatever its called seized up and took the belt out with it. I got a pulley that resembles it from Autozone mind you that it was the only parts store that had one in stock even Hyundai didnt have the part. The only difference is the hole size for the bolt is about 1/4 inch bigger then the stock pulley. Is there any chance I can get a spacer and make up for the difference?
View 6 RepliesCamry :: Engine Noise - Bad Serpentine Belt Tensioner Is Seized On
After finally identifying a bad serpentine belt tensioner for being the the culprit for my engine noises, my mechanic said that the 'thru-bolt' is siezed. Since the replacement job was at my budget limit he said he doesnt want to get into it in fear that he has to brake the bolt and drill it out (requiring 2-3x more labor cost according to him).
If this is the case, and the 'thru-bolt' is seized, is this in any way something I can make a an effort to tackle? I have a jack and jack stands, and plenty of time.
Ford 6.0L Power Stroke Diesel :: Doing Idler And Tensioner Pulley Bearings - Fan Shroud Removal?
Looking for how to's out there on how to get all of the fan shrouding removed? I am trying to do my idler and tensioner pulley bearings and those shrouds really make it tough.
View 6 RepliesCamry :: Nut That Hold Pulley On Alternator Fallen Off - Serpentine Belt Will Not Stay On
The nut that holds the pulley in place on the alternator has fallen off, causing the pulley to become loose and now the serpentine belt will not stay on. What is the size and thread type for the nut that I need to replace?
Alternator Pulley Nut for 2004 Camry 4cyl
Ford Ranger / B-Series :: Squeak When Running / Idler Pulley For The Timing Belt
In a few weeks I will be bringing my new to me Ranger back to the great state of Texas. The truck however, has a squeak when running, which I think has been concluded as the idler pulley for the timing belt. Well, I'm nowhere near the truck still and in order for it to get here it will need to be driven half a day to reach me, at which point I could do all the work it needs done.
My question is: Should I take the risk and have it driven here before the belt change (I did look at it while I was out there and it's already cracking pretty good), or should I go ahead and have someone get the belt done at a shop? It's less the belt that concerns me I think, and more the pulley, even though it's just started squeaking in the last 1000 mile.
Ford Super Duty (1999-2016) :: 2002 F250 - Replaced Idler / Tensioner / Belt But Still Getting Whipping Noise?
Ok I have a 2002 f250 7.3 4x4. The belt starting to shred and make a whiping sound at highway speed. So I replaced the idler, tensioner and belt. That was not the problem it still making noise so next I changed water pump. Still not it so I changed a/c clutch, bearing, and pulley. And It still not fixed. Right now the back of the belt is turning black on the wrighting like a pully is locking up. Also the front edge of the belt is starting to wear. I only have 255,000 miles on the truck and has been well maintained.
View 14 RepliesSonata NF (2006-10) :: How To Replace Serpentine Belt Tensioner On 3.3 V6
How to replace the belt tensioner. It's not putting out enough tension when the engine is cold. So, the belt makes chirping noise for couple of minutes idling when cold with AC on.
I had the AC inspected and everything checks out according to my mechanic.
He believes that the issue is with the tensioner since I had recently had replaced the serpentine belt.
Tiguan :: New Serpentine Belt Tensioner After 1000 Miles?
I had my timing chain tensioner replaced. When they do this do they touch the serpentine belt tensioner? 1000 miles after the timing replaced, my serpentine belt shredded and they say I need a new serpentine belt tensioner. Does this sound correct?
View 3 RepliesToyota - Camry :: 2006 - Water Pump And Serpentine Belt Replacement
Is it possible to change the water pump and serpentine belt in a 2006 Toyota Camry with 4 cyl. engine in less than an hour?
View 4 RepliesFord F-150 (2004-2008) :: Possible Belt Tensioner Pulley Bad
I have a 2008 F-150 with a 4.6. I have a sequel and I believe it is the belt tensioner pulley and / or the idler pulley above it. Looking for proper procedure to change one or both. It is pretty tight in there. How much stuff do I have to remove to get in there. Should I replace both pulleys at the same time.
View 2 RepliesGolf/GTI VI :: Chirp / Squeak Under Hood - Bad Serpentine Belt Tensioner?
So my mk6 developed what initially sounded initially like a bad serpentine belt tensioner. Only under anything more than load, and sounded like a bird chattering under the hood. Got outside today, fired car up, watched tensioner and it sat there steady as a rail. The noise is coming from the opposite side of the engine. Not really mechanical/metallic at all and tracks under load with the RPMs. Why i initially thought what i did. Not I'm sort of baffled.
View 3 RepliesChevrolet - Suburban :: Vibration After New Serpentine Belt Tensioner Installed
I installed a new serpentine belt tensioner into my 1994 Chevy Suburban C1500. It vibrated as much as the old one did, so I assumed that a bit of vibration is normal and forgot about it. Well, after recently looking at some instructional videos, I am now under the impression that any vibration in the tensioner is bad. Here is what is going on -- [UrL] .... Is it OK or should I get another new tensioner?
View 4 RepliesAzera TG (2006-11) :: Serpentine Belt - Crank Pulley Failure
Ever hear of a crank pulley failure? Mine did and took out the serpentine belt. I have 63,000 miles on the 07 and it was a big shock to see the pulley in two parts.
View 5 RepliesFord Aerostar :: 1997 - Squeaking Noise When Turning - Serpentine Belt Tensioner?
I have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 RepliesFord F-150 - 1997-2003 :: Noisy Serpentine Belt - Crank Pulley Squeak?
Been trying to isolate my noisy serpentine belt. Had the belt off and spun everything, only thing I found that made any noise was the alternator. It had a nice churp like a bearing was on its way out in it. So I replaced that figuring my squeak was going to go away. No such luck. Listening to it again while it was idling, I crawled underneath. Almost seems like the churping noise is coming from the Crank Pulley. Is there a bearing on this pulley that goes bad?
View 13 RepliesCamry :: 2006 - Loud Noise Coming From Idler Pulley On Cold Startups When Put It In Gear
I have a 2006 Camry 2.4l and I'm hearing a loud noise coming from the idler pulley on cold startups when I put it in gear. I don't hear it when it's in park. The noise gets worse if you turn the a/c on. I have replaced the belt, idler pulley and top motor mount. I took the belt off and cranked it when cold and there was no noise even in gear. I can see the idler pulley moving and can confirm that's the noise but what it causing the belt to make it do that? Could I have bought a defective idler pulley?
View 3 Replies