Honda - Pilot :: Timing Belt Frayed Broke Due To Idle Tension Pulley Failure

I am working with Honda dealership management because I had my timing belt changed at 102,000 miles and 25,000 miles later The belt broke and frayed while driving in heavy traffic at night on freeway leaving me stranded in the median luckily instead of in the middle of the freeway. Honda dealership stating that the idle tension pulley caused the fraying of the belt not due to poor workmanship by their mechanics. I am asking dealership to consider assisting in payment because the day the belt went out, the car had been serviced for a oil change.

When I was called to be notified the job was complete I asked the service rep questions about the oil transmission and told him there was a noise in the engine could they check it or did they check it which she replied no that I would have to make another appointment for that. So even if I would've made appointment the next day the damage was already done because that night is when the belt broke Is this part of Hondas responsibility is it reasonable for them to take part responsibility. Also if the idol tension pulley had been changed at the same time of the belt, it would've saved my engine. So this is all my responsibility not theirs?

View 19 Replies

Ford Super Duty (1999-2016) :: 2006 - Serpentine Belt - How To Route The Belt Around Tensioner Pulley

2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.

I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.

It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.

View 4 Replies

Accent LC (2000-05) :: 2002 - Timing Belt Tension Adjustment

Is there a "how to" on adjusting the tension of the timing belt in a 2002 accent 1.5L ....

View 1 Replies

Camry :: Nut That Hold Pulley On Alternator Fallen Off - Serpentine Belt Will Not Stay On

The nut that holds the pulley in place on the alternator has fallen off, causing the pulley to become loose and now the serpentine belt will not stay on. What is the size and thread type for the nut that I need to replace?

Alternator Pulley Nut for 2004 Camry 4cyl

View 1 Replies

Elantra HD (2006-10) :: How To Set Tension On Timing Belt Tensioner

I am deep into replacing the timing belt on my 08 Elantra 2.0, and am nervous about taking the tensioner off since it is not obvious how to set it. I could use a fool proof explanation on how to set the tensioner.

The Haynes manual talks about 1/4 deflection but that seems too imprecise.

I can not see the marks in the video : DIY 2008 Elantra timing belt video 2 of 2 - YouTube

And this post 2008 Elantra Timing Belt does not quite seem to explain. I am contemplating putting it all back together, just changing the accessory belts and handing it to a shop. I could use a fool proof explanation on how to set the tensioner.

View 7 Replies

Azera TG (2006-11) :: Serpentine Belt - Crank Pulley Failure

Ever hear of a crank pulley failure? Mine did and took out the serpentine belt. I have 63,000 miles on the 07 and it was a big shock to see the pulley in two parts.

View 5 Replies

Subaru - Outback :: 2008 - Power Steering Pump Replacement / How To Adjust Belt Tension

I'm about to replace my 2008 Subaru Outback's power steering pump. Only question is: How do I adjust the belt tension? Looks like the pump is stationary, and I suspect the alternator is the key, since the belt turns that as well.

View 2 Replies

Honda - Odyssey :: 2006 - Serpentine Belt Breaking The Timing Belt

Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.

View 11 Replies

SC/SL/SW :: 99 Saturn SL1 Squeaking Belt Or Pulley Sound

It has developed a weird squeaky belt or pulley sound. It starts after few seconds of start up and goes away after driving few kms. It also goes away immediately for few kms. When I spray WD-40 on generator/alternator. Once in a while the sound decreases by itself and goes away only when I press the gas pedal and comes back during idling/braking. The belt is almost like a new. The car drives great without any issue.

View 1 Replies

Accent MC (2006-11) :: How To Disable Seat Belt Chime

I just bought my 06 Hyundai accent last night. Just today I noticed my seat belt will chime after I remove the belt, even if the car is in park. It's not a big deal but it was enough to make me look through the owners manual to see if it could be disabled. Well, I didn't find my answer so I thought maybe someone here has already done it. So, how to disable the seat belt chime?

View 7 Replies

Accent MC (2006-11) :: How To Properly Install A Timing Belt

Rebuilt a motor due to the timing belt failing. Everything works except I can't get the timing to line up perfectly.

From what I'm getting from the service manual, line the camshaft sprocket with the mark visible from the hole

Line up the crankshaft gear with the yellow mark at the bottom.

Do I have to do a double/triple turn of the cam/cranks to get TDC to be achieved properly? My biggest problem on this car is having the crank gear shift a couple teeth after tensioning the belt.

View 4 Replies

Geo - Prizm :: Cannot Remove AC Belt / Pulley Is Stuck In The Bracket

I'm trying to remove the AC belt off a '96 Geo Prizm. I've loosened the idler pulley adjusting bolt, per my Chilton's manual, but it doesn't loosen the belt. It's as if the pulley is stuck in the bracket. Even if I completely removed the adjusting bolt the pulley wouldn't budge. How can I unstick this thing without damaging the pulley?

View 6 Replies

Ford F-150 (2004-2008) :: Possible Belt Tensioner Pulley Bad

I have a 2008 F-150 with a 4.6. I have a sequel and I believe it is the belt tensioner pulley and / or the idler pulley above it. Looking for proper procedure to change one or both. It is pretty tight in there. How much stuff do I have to remove to get in there. Should I replace both pulleys at the same time.

View 2 Replies

Accent MC (2006-11) :: Seat Belt / Battery Light Both Flashing Then Going Off

6 months ago After replacing both the battery and the alternator..The seat belt light and battery light both began flashing and then going off ..with no loss of power.. It has been coming on a lot more lately,with no loss of power...I do have a mass air flow code coming up with no issues as far as the car goes..no issues driving. So with a new alternator and battery put in what can be the issue?

View 4 Replies

Accent MC (2006-11) :: 2008 - Won't Start Up After Replacement Of Timing Belt

The timing belt broke in my gf's '08 accent recently and I decided to have a crack at replacing the belt after getting a quote for $900 from the nearest mechanic (with no guarantee it would fix the problem).

When re-aligning the cam and crank to TDC, I wasn't sure if it mattered which revolution the crank was on (ie. 1st or 2nd revolution) when putting everything back together. I tested rotating the engine with the new belt on slowly to make sure there was no contact and everything seemed ok.

So basically now everything is back together, tried starting it up and it won't start and now i'm wondering if it would make a difference or not if the crank was rotated 1 additional revolution. Otherwise there is more significant damage.

View 17 Replies

Camry :: Engine Making Noise Seems Like Belt Pulley Bearing Is Going Out

I have a 2009 Camry 5spd with 92K miles on it. Camry is completely stock and original with meticulous services to engine oil and drained the transmission fluid at 68K miles. I am hearing an engine hum every now and then (although I notice it more often now that I am searching for it) while I am idling. I don't believe it to be engine vibration, rather it is a hum, seems like a belt pulley bearing is going out, or even, and i hope its not, like my throw out bearing in the clutch is going bad.

Only reason I say that is because it makes the hum for a few seconds then goes away, then comes back for a bit. It makes the hum when i have the clutch engaged and when i have the clutch disengaged and a in neutral. I have opened the hood to try and search from where it is coming from but it is just too darn hard to figure out.

I am hoping it is nothing related to my transmission. I may pull the fill plug on it this weekend and try to stick my finger inside to see if I am low on fluids and it is making a hum (but I highly doubt it because when I filled it up after drain i filled it too the top). I haven't experienced any burning of oil and use 5W-20 (Castrol GTX since day 1). I may switch fluids on my next change and use maybe a different brand and viscosity (maybe use standard Quaker state at 5W-30).

Again it isn't an engine vibration, rather just a hum or almost like a stinking wobble and then goes away for a few seconds. I say wobble kind of like you would hear a drive shaft on a truck that wasn't balance properly and was spinning without being centred with counter weights.

View 1 Replies

Camry :: Idler Pulley Replacement On Serpentine Belt Tensioner

2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.

View 2 Replies

Corolla / Matrix 2009-13 :: Free Rev Before Falling Into Next Gear / Serpentine Belt Squeaks

I had put on about 300 miles on the car in my sig before this started happening. Every once in a while as the car goes to upshift it will free rev a couple hundred rpm before falling into the next gear. I have not been driving it hard at all and have been driving easy when this happens.

Could be something as simple as needing a fluid change but the thing only has 34,000 miles on it, I hope it's not serious.

Upon a cold start up it sounds like the serp belt squeaks for about half a second on a pulley that isn't spinning freely. That's what it sounds like. I am just wondering, are these "known issues" with these cars?

View 6 Replies

Elantra XD (2001-06) :: Belt Squeaks And Sometimes Sounds Like Grinding And Lose Power For 4 - 5 Seconds

I have a 2005 Elantra GLS. I've noticed that anytime it rains or I hit a puddle, my belt squeaks and sometimes it almost sounds like it's grinding and I lose power for 4-5 seconds. From the front passenger wheel well, I can clearly see the belt. I noticed there are holes drilled into the frame, and I was wondering if there is suppose to be a guard there to prevent water from getting on the belt?

View 2 Replies