Camry 2012+ :: Front License Plate Mounting?
Mounting front license plate somewhere other than the "official" mounting location? I don't like the thought of putting holes in my front bumper. I can move it down a bit such that the holes are in the bumper just above the air opening. So, they would be less noticeable. This would block some of the airflow through the lower opening. But, unless I'm driving in 100+ deg temps, it probably won't matter.
I could also offset it to the right or left in the lower opening.
Camry 2012+ :: Tow Hook License Plate Mount?
where to get it? I want to plug up my bumper holes and just put the plate on the tow hook.
View 14 RepliesCamry 2012+ :: One Of License Plate Lights Doesn't Turn On Until Tap It
One of my license plate lights doesn't turn on until I tap it..
What could be causing this? I installed LED's in them but a few months later I noticed this happening.
Camry 2012+ :: License Plate Rattle At The Back Of The Car Whenever Shut The Trunk?
I have a 2013 Camry SE and I am experiencing the annoying license plate rattle at the back of the car whenever I shut the trunk or drive over bumps. It's really getting to me as of late?
[URL]
Camry :: Can't Remove License Plate Screw
Was trying to remove the licenses plate screws today. One comes out easily, the other won't budge. I've sprayed a couple of times with WD40 but its still stuck.
View 14 RepliesPrius (Gen 3) :: 2012 - Stuck When Turning Stock License Plate Bulbs 1/4 Counterclockwise
I am trying to swap out my stock license plate bulbs on a 2012 Prius.
After getting to the bulb socket holding thing, I have read that you're supposed to turn it 1/4 counterclockwise and pull but mine is stuck and won't turn either way.
Lexus IS 2014+ :: Rear License Plate Mount Rusting Already?
My Ultra white IS350 is 15 months old, and when I took out the screws to my license plate today, I noticed a little bit of rust on the mounts (where the screws would go into).
I believe this is a pretty common issue for all cars - essentially, the mount was sprayed with body paint, but the paint would be stripped when you put a screw in. It's just a matter of time before that happens.
I am just concerned it would rust through my trunk if I continue to leave it.
FYI: I already use stainless steel screws
Corolla / Matrix 2009-13 :: Bolts Size For Rear License Plate?
what size bolts are needed for the rear license plate?
View 7 RepliesCamry :: 2002 - Remove And Replace Burnt License Plate Bulb
02 Camry, how to I remove the burnt license plate bulb? Took off the underside trunk carpet and disconnected bulb harness, but I don't know how to remove the plastic piece that holds the bulb in place. Does it pull out, or twist out? I don't want to break it!
View 1 RepliesLexus RX 2010-15 :: Removing Rear License Plate Trim On 2015 Fsport?
how the chrome trim above the rear license plate is removed?
View 4 RepliesGolf IV / Jetta IV :: Right Rear Tail / License Plate Lights And Back Windshield Wiper Doesn't Work?
I'm having some sort of electrical malfunction on the back of my Mk4 Gti. The right rear tail light, license plate light and back windshield wiper doesn't work. I replaced the bulbs several times and they keep blowing.
View 2 RepliesCorolla / Matrix 2009-13 :: Light Bulbs For The Rear License Plate Light Is Out?
One of my light bulbs for the rear license plate light is out.
what kind of light bulb I need to get?
Camry 2012+ :: Samsung S3 Phone Contact Sync
Ok, so I got the car, and had been trying to sync my phone contact (samsung s3) since the first day, everytime i try to sync, they would only upload one contact and that is my phone number. I have been reading around and tried almost everything, turn phone off, restart etc.
The reason for it is, I save my phone contact to sim card and not on the phone itself, so I believed the car only sync with the phone and not the sim, so try to move your contact to the phone and let it sync.
Camry 2012+ :: Canister Flange Won't Make Contact With Engine At All
Just changed the engine oil on the 2012 TCH. I didn't pay close attention when I took the larger O-ring off the plastic canister and when I was putting a new one on, I wasn't sure where it fits.
There's a wider notch at the bottom of the threads. The new O-ring (Toyota Genuine) was a little bit lose fit in this spot, but this is where I put it as there seemed to be a angled bevel at the base of the filter mount where the canister fits into the engine. I did oil the O-ring and the bevel on the canister mount on the engine with new TGMO 0w-20. It was tightened to 25 Feet Lbs as listed on the plastic canister, but I could hear the friction with the O-ring. No leaks from what I can tell after the fill.
Then there's base of the flange on the plastic canister that sits flush to the base of the engine. The ring fit tight in this spot but then would be pinched between the engine and canister flange such that the canister flange won't make contact with the engine at all. I don't think this is where the larger O-ring should have gone.
Any pic of where exactly the large O-ring sits on the plastic canister?
Camry 2012+ :: Contact Coming From Below Front Portion Of Car While Going Over Speed Bump
I have a 2014 Camry. I went over a speed bump at around 30 MPH, and as the front wheels went up to the top of the speed bump, I heard a definite sound of hard contact coming from below the front portion of the car, possibly near the right wheel. The sound wasn't loud, and it wasn't followed by any other sound. It was just "bump."
The car seemed fine after, and I drove for another five miles or so noticing anything different. I looked under the car, and I didn't see any signs of damage. There was some water condensation dripping down, but I think that's just because I had been using the AC. Do you think I have any reason to worry? What signs should I be on the lookout for?
FYI, the speed bump was one of those wide ones with a gentle curve. It looked like a slight, gradual elevation in the road, and the paint had washed off. So I didn't see it. It wasn't a narrow speed bump that you have to slow down to 10 MPH for.
Ford - F150 :: 1998 - Throw Out Bearing Not Allowing Pressure Plate To Make Proper Contact With Clutch
I have a 1998 Ford F150, Manual transmission. It has set for 1 year. Upon driving it for the first time yesterday, it gradually came to a stop. The clutch never smelled hot or appeared to slip. Today I took the inspection cover off and found a rather large nest has been built in the clutch and pressure plate. My question is could this nest cause the throw out bearing from allowing the pressure plate to make proper contact with the clutch. The truck will move in 1st gear and in reverse as long as there is no resistance against the truck.
View 2 RepliesRegal :: 99 - How To Change License Plate Bulbs
How to change license plate bulbs? The little clear covers dont seem to pop off ........
View 3 RepliesPassat (B6) :: LED License Plate Lights Not Working?
So I bought LED license plate lights, the same ones Track5tar has (who sent me the link to get them). I got em off the bay, and I put them in and they don't work! The Heatsink gets hot but the lights don't light up in both of them!
View 24 RepliesPassat (B6) :: License Plate Lights Won't Turn On
So I was replacing the lights with the new leds change one toke some pics to compare. Everything fine...
Removed the other feston put the new led and they won't turn on anymore..
Change them back. Put them upside down, up, sideways... Nothing
Check all three fuse boxes all ok
Every other light on, inside trunk on, side markers on...
Everything but the license plate lights.