Camry :: 2005 - Dash Power Outlet Replacement
2005 camry ... How do i replace the dash power outlet? I have the heating and air panel out and the bottom of the outlet panel unsnapped. I can't figure out how the top comes loose.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 4x4 Won't Move - Trans Busted?
I have a 2006 F350 4x4 dually (6.0 diesel obviously) automatic. It's got 200kml on it and a second motor (found the sticker on the valve cover). I just bought it a month ago and have only driven it like 100-150 miles. Previous owner imported it to Finland 3 years ago, but never registered and only drove it like 500-1000 miles (with temporary plates to carry his racer few times). Original owner was a company in Southern Midwest that had some equipment on back. (It's was sold as a chassis cab new.)
Now I was getting the truck tested for registration yesterday. Drove it there 30 miles (country roads and highways), no problems. Then we had to do the smog-test, which is a bitch. They rev the engine to limiter (4200rpm) couple of times and measure the particles flying out. Passed it flying colors, but when trying to pull out the transmission wont engage!
Shifter linkage ok. Oil in tranny clear and plenty. When I put on R or D the engine RMP rises very slightly (maybe 50-100 rpm) and then settles back. But nothing else happens.
Luckily got a friend with large flatbed that we used to carry my baby home. But now I don't know where to start... ...well, I do have couple of ideas what could be broken. Specially if there's something simpler than dropping the whole tranny out (it's HEAVY and it's cold&wet out there) and rebuilding the whole damn thing.
Previous owner told he had some shifting issues couple of years ago (maybe 500 miles ago) and they "rebuilt" the tranny. He DID replace the hydraulic "logic board" and solenoids + new packs while at it. Naturally new filter & oil too. He said the torque converter was "tested" to be in good condition and they used the old one. I can tell the tranny has been out of the truck and the seller felt legit (a car guy too).
Camry :: 2002 - Connecting 12 Volt Power Outlet To Fuse Box?
How do I connect this ↓ to Camry 2002 Fuse Box - down, to the left of the steering wheel? Where do the red & black go?
View 14 RepliesCamry :: 2005 LE - Cigarette Lighter (Power Outlet) Doesn't Work
I have a 2005 camry le, but just now the power outlet doesnt work. I have checked multiple items in both the outlets, but none of them work. I checked the fuses, but they all look fine. The items work in other cars, just not this camry.
View 4 RepliesToyota - Camry :: Power Outlet Fuse Blow When Plug In Phone And Charger Cord
When I plug up my phone and charger cord to either power outlet on my 2009 Camry the fuse blows. The charger cord and phone works in my other vehicles. I have checked other power cords in the Camry and it also blows the fuses. Would this be a relay that controls the fuses?
View 1 RepliesElantra HD (2006-10) :: Power Outlet / Lighter Is Not Working - Fuse Checked
I have bought a 2007 Elantra recently, and I have noticed that power outlet/ lighter is not working. I have checked the fuse but it is ok. I have to access the back of the power outlet to check the cables but I do not know how can I do it. How can I access the back of the power outlet step by step. Looking for some pictures or videos ....
View 5 RepliesLexus GS 2006-11 :: Busted Front Passenger Tire
So I hit a pot hole today and bust my front passenger tire, and possibly bent my frame on the front end.
I have an 07 350 AWD.
Passat (B6) :: All Power Lost Like Have No Turbo - Possible Busted DV?
I think I have a busted dv. The car has lost all power feels like I have no turbo. One code when looked up says it could be a possible busted dv but can the other 2 problems be caused by this?? Also if I drive it very easy until the part comes Monday can I damage my car??
VCDS Version: Release 10.6.3
Data version: 20101206
Friday,15,April,2011,16:33:40:16973
Chassis Type: 3C0
Scan: 01 02 03 08 09 0F 15 16 17 19 25 37 42 44 46 52 53 56 62 65 72
VIN: WVWEK73C76P109439 Mileage: 83400km/51822miles
[Code] .....
Camry :: AC System - Rear Outlet Blows Really Hot Air
If I've been traveling on a hot day with A/C on, at some point after 3-4 hours, the air coming out of the REAR outlet starts to blow HOT.
Again, front A/C outlets still blowing nice cold air, but rear outlet blows really hot air. If you shut the A/C off for 1/2 hour, (or shut the car down for 20-30 minutes), when the A/C runs again, everything is fine again.
I think it must have something to do with icing (?) and the flaps on the ventilation system. Any diagram of the system?
Ford Super Duty (1999-2016) :: 2006 F250 - Front Driver Side Brake Line Busted
So I'm away from home on vacation also away from my tools. Any ways my front drivers side line busted almost causing me to crash earlier today in my 2006 F250 6.0 diesel 4x4. So basically my question is: what tools are needed to do this job? I've already picked up the part now tomorrow morning I will be changing the part...
View 2 RepliesCamry :: 2006 - Reprogram Key Fob After Battery Replacement
I've got a strange problem with the keyfobs on my 2006 Camry. I tried replacing the batteries in both keyfobs and reprogramming them, but they still will not unlock the door. I suspect there is an issue with some computer part in the car that is preventing it from working. This was my sequence of events:
1. The key fob stopped working, so I replaced the battery. No luck.
2. Found the spare fob, didn't work either so I replaced that battery too. Still didn't work.
3. Reprogrammed both remotes using the steps (pasted below for readability). The programming was successful because the door locks cycled after adding each remote to the ecu on step 13.
However, after exiting the vehicle the locks still weren't working.
The steps I followed to reprogram the key fob:
1. Begin with the key out of the ignition.
2. OPEN and UNLOCK the DRIVER'S side door. CLOSE all other doors including the trunk.
3. Within 5 seconds INSERT the key into the ignition and PULL it out TWICE.
4. CLOSE then OPEN the DRIVER's side door TWICE.
5. Insert key INTO the ignition then REMOVE it.
6. CLOSE then OPEN the DRIVER's side door TWICE.
7. Insert the key INTO the ignition and LEAVE it in ignition.
8. CLOSE the DRIVER's side door.
9. Switch the ignition to ON then OFF.
10. REMOVE the key from ignition.
11. The door locks will now cycle to confirm the vehicle has successfully entered programming mode.
12. PUSH and HOLD the LOCK and UNLOCK button for 1.5 seconds on the first remote being programmed. As soon as you let go PUSH the LOCK button and HOLD it for 2 seconds.
13. The door locks will cycle to confirm successful programming of the remote. If you have any additional remotes to program repeat step 12 if you have no additional remotes proceed to step 14.
14. OPEN the DRIVER'S side door. Programming is now complete. [URL].................
Camry :: 2006 - Brakes Squeak After Replacement
Independent mechanic replaced brakes and rotors on my 2006 Camry LE with NAPA parts. All was fine for a week or two but now I'm getting a squeak when I apply the brakes. Mostly this is at low speed. the squeak varies in loudness and length and does not happen all the time. Also after repeated stops, the brakes will grind at the tail end of braking (right before the car comes to a complete stop).
Stopping distance is not affected nor is there any vibration. I plan to take it back to the mechanic later this week but what the issue could be?
Camry :: 2006 V6 - Code P0136 / CAT Replacement?
My 2006 Camry V6 had the code P0420 before. I replaced 2 downstream O2. Now it throws code P0136. What should the next step I am looking for here? Is it a CAT issue? If I need to replace CAT, do they have custom (modify) CAT to improve the performance?
View 5 RepliesCamry :: Valve Cover Gasket Replacement On 2006 V6
So I'll be taking on a project to replace the valve cover gasket on my 2002 Camry V6. There's a bit of leakage through the gasket. And while I'm at it, I'll replace the spark plugs as well. I'm looking for a write up on this project. did a lot of searching but couldn't find anything.
View 14 RepliesToyota - Camry :: 2006 - Water Pump And Serpentine Belt Replacement
Is it possible to change the water pump and serpentine belt in a 2006 Toyota Camry with 4 cyl. engine in less than an hour?
View 4 RepliesGolf VI R :: 12v Power Outlet - Changing From Keyed Power To Constant On
Change power supply to the 12v power outlet to a constant on power source?
Do it just a matter of a jumper wire or does a new wire have to be run to the outlet?
Ford 6.0L Power Stroke Diesel :: 2006 - Power Steering Pump Replacement
When replacing the power steering pump on my 2006 should I go OEM on the pump or save some money and get a Napa or aftermarket remaned unit with the pulley installed? Also, whar is the fluid capacity of the power steering system?
View 14 RepliesCamry :: 08 - Power Outlets Fuse Replacement
Went looking at replacing the fuse for both power outlets, Couldn't find it. Checked under dash and engine compartment. Checked them all since I didn't know which one was it. Where to look? Everything else works fine on the car. radio, lights, all
View 2 RepliesCamry :: Power Window Regulator Replacement
This procedure explains how to remove the driver side, rear door panel, test the power window motor and switch and replace the power window regulator assembly.
Tools Required: #2 Philips screwdriver, small slot screwdriver, 10mm socket wrench, jumper cables, set of test leads with alligator clips, DC voltmeter.
Cost: In the end, I did not end up buying a new window regulator assembly, but I think a "Dorman 741-356 Rear Driver Side Replacement Power Window Regulator with Motor for Toyota Camry" would work.
1. Locate the anchor (red arrow). Push the center in and then pry the anchor out with a slot screwdriver.
2. Remove ashtray, pry and remove the rubber liner and remove the #2 Phillips screw.
3. While pulling the door handle, carefully pry the plastic trim piece away from the door handle bezel and remove the #2 Phillips screw.
4. Pushing the door trim piece forward, pry the rear upward. Note that there is a plastic tab (red arrow) at the front of this trim piece, so it is necessary to lift it from the back to avoid breaking it.
5. Squeeze the electrical connector to remove it from the socket and then set the trim piece/switch assembly aside.
6. Remove #2 Phillips screw (red arrow).
7. Remove two #2 Philips screws (circled in red) at the bottom of the door.
8. Grasp the bottom of the door panel with your fingertips and gently, but firmly pull outward to disengage the 9 snaps on the door.
9. Lift the door panel upward to unhook it from the door. Carefully set the door panel on the ground.
10.Pull the white plastic cable guide out of the sheet metal holder and rotate the cable housing to disengage the cable from the mechanism. Pull the green plastic cable guide out of the sheet metal holder and rotate the cable housing to disengage the cable from the mechanism. Gently set the door panel aside. %