Accent RB (2012+) :: Creaking Noise On Releasing Clutch Pedal
On releasing the clutch pedal, a creaking noise can be heard, which:
- sounds and feels like a rusty spring being unloaded
- occurs for the entire range of pedal travel, but worse near the bottom
- is louder outside the car than inside
- happens not only when driving, but also when stationary with the engine off
I don't think anything is wrong with the clutch itself, or any bearings, or major components... It just feels like something needs to be lubed. I've lubed the spring above the pedal inside the car, with no real effect.
Accent RB (2012+) :: 2013 - Car Rolls After Parking / Clunking Noise While Releasing Brake From Stop
2013 accent auto My car rolls noticeably after parking unless the ground is completely flat. Parking brakes prevents it from rolling but I don't use parking brakes every time. Another brake problem I have is thump or clunk noise I get whenever I release a brake from stop.
View 12 RepliesAccent RB (2012+) :: Clutch Has Been Really Stiff For A While
It's been a while, but my clutch has been really stiff for a while now. I don't think it was always this stiff. My mother has the same car and her clutch is really "light" and is very easy to press in. While mine is about as stiff as my friends corvette.... Is it just normal in that all clutches feel different or could something be wrong?
View 2 RepliesAccent RB (2012+) :: Engine Revs When Clutch Depressed
I bought my Hyundai new in late 2011. No problems with the car (other than no spare tire???) until just out of the warranty (63,000). Had a noticeable drop in power on the highway. No warning lights. Drove another 100 miles with power intermittently dropping. Next day engine light comes on. $800 later I have a new high pressure fuel pump. All seems well. after a few weeks, I notice that the car seems to be revving when I depress the clutch to change gears, like up to 4000 rpm's. If I leave the clutch in for a few seconds it will begin to decrease. But if I shift right into gear as I have done for the last 35 years of driving, it is not smooth, jerky. This seems to happen mostly going into 2,3, and 4th gear, always going up. It never happens when downshifting. I tried tapping the brakes when shifting up, and sometimes it does seems to drop the rpm's. What it might be. It probably is related to the work that was done, but I don't really trust the dealer and want to have a little info going in.
View 1 RepliesAccent RB (2012+) :: Engine Revving Itself Higher The Second After Push The Clutch In
Today I started my car (in the garage so it wasn't too cold) and everything was fine. The car warmed up in a couple minutes and I was off.
As i was driving, I noticed that my shifting was horrible. It felt like i was burning the clutch and not releasing the clutch smoothly in general.
I then noticed that when i pressed in the clutch ready to take the next gear, the engine would raise the rpm's about 500-1000 revs before coming down.
I started to wait till the revs came down to shift and that seems to work.
Why would the engine be revving itself higher the second after i push the clutch in. My dealer can't take me until Wednesday so I don't know what to do.
Car Shaking While Releasing The Clutch When In First Gear
I've A Problem With My Car Nissan Tiida 2007
When In First Gear While Releasing The Clutch The Car Shakes
And If I Didn't Release It Fast The Engine Will Stall
Accent RB (2012+) :: 2013 - Clutch Pedal Adjustment So That Engagement Isn't So Far Away From The Floor?
In most other manual tranny cars that I have ever driven, the clutch pedal engages/disengages within an inch of the floor. Not my accent. is it possible to adjust the clutch pedal so that engagement isn't so far away from the floor? it pretty much fully engages at the near top of the pedal.
View 2 RepliesGolf IV / Jetta IV :: Creaking When Pushing In And Releasing The Clutch
I have done some research, but have found no one with the same noise as I am having. My clutch is creaking when pushing in and releasing the clutch. It does not sound like it is coming from the pedal. I have had a new clutch and transmission replace within the past 18 months. Someone mentioned the creak could be "dust on the slave cylinder." What this could be? Should I be worried? It shifts perfectly find and rides fine.
View 3 RepliesGolf IV R32 :: Transmission - Loud Clunk When Releasing Clutch Pedal
My R has been giving me some trouble lately. First I had some issues, I thought were clutch related.
-A loud clunk when releasing clutch pedal (only when engine running) and sometimes when depressing it too.
-Randomly changing clutch biting point when driving hard. So e.g. when revving through 1st and 2nd gear the clutch would bite much lower than usual. (This was so weird.)
-Whistling sound when changing from 1st to 2nd gear.
Replaced the clutch, flywheel, pressure plate and the TOB and bled the system several times. Also new solid DLI motor mounts and new oem dogbone mount.
There was some side-to-side play on input shaft that I was told is not a big deal. Also this gearbox has always been much louder than other cars Ive driven.
Now that weird changing clutch biting point is gone but other issues are still there. And now, because of the lightweight smf and the motor mounts the gears shatter and whine so much more on low revs and during engine braking. I know 02m s tend to do that but its so loud I am a bit worried.
Ford 6.0L Power Stroke Diesel :: A/C Compressor Clutch Won't Releasing
The clutch in my ac compressor is not releasing causing it stay on all the time and not cycle and get hot and freeze up the system. Also pulley seems to be angled like it's not sitting straight. Can I just replace the clutch on the front? if so what's all involved. I need to do the entire compressor?
View 12 RepliesPassat (B6) :: Creaking / Groaning Noise From Foot-rest Area When Releasing Clutch
As stated in the title, I've been experiencing a creaking/groaning noise originating from the dead pedal/foot-rest area when I release the clutch as I'm accelerating from first gear. This happens more so when I'm accelerating from a stop on any sort of incline (irrespective of the grade) and primarily in the afternoon/early evening when the weather's at its warmest for the day.
The noise itself originated about a month ago. Although I describe it as a creaking/groaning it sometimes sounds like a slight metal on metal friction noise.
My car's stock with the exception of Driver Gear springs and a BSH 27mm sway bar in the rear. Wheels are OEM 16s. I've had the DG springs on my car for about 3 months before this noise began and mileage was around 9,900Km.
Toyota - Tacoma :: 2001 Bucks / Jumps Like Clutch Is Alternately And Rapidly Grabbing And Releasing
My 2001 Tacoma drives well most of the time, but when in 4 wheel drive low range, low gear, in demanding circumstances like heavy snow, it will buck, jump, act like the clutch is alternately and rapidly grabbing and releasing (but I'm pretty sure it's not actually that). Tires are good. Four cylinder, standard transmission.
View 7 RepliesHonda - Accord - Clutches :: 2000 - Rumbles Or Shudders When Releasing The Clutch After Shift Into Second Gear
I just rolled over to 90,000 miles on my 2002 Accord. Its running beautifully, however every so often the car "rumbles" or "shudders" when I'm releasing the clutch after I shift into second gear, or sometimes it'll do it when I'm facing up a hill pulling into first gear letting out the clutch. Its almost as if the clutch rapidly grabs then slips a bunch of times, similar to if it was warped. It doesn't completely slip at all to my knowledge. The car was bought new by my family and has been driven pretty carefully since (although 2 people have learned to drive stick on it, and my dad isn't the most "gentle" driver in the universe). I know that Clutch rebuilding and replacing is a big expensive job and its something I wouldn't even consider doing myself. So, when is it time to really seriously consider dropping down the serious cash to get the clutch rebuilt? To be honest, the shuddering is really annoying (it doesn't happen all the time though) but its something I could live with for a bit.
View 8 RepliesAccent MC (2006-11) :: Brake Squeak When Releasing Pedal
Started a few months ago didn't really bother me until now. Started when I would forget the parking brake is on and would just put the car in reverse & wouldn't move until I released the parking brake. Did it about 5-7 times and now every time I brake without the parking brake on, it squeaks & is really annoying. Is there any way to fix this or is it just gonna be complicated & expensive?
View 10 RepliesAccent LC (2000-05) :: Squeak When Releasing Brake Pedal
2004 Accent 1.6L 5spd
Purchased this car used with 64k miles on it. I am in the process of performing the 60k miles service items and going through typical replacement of worn parts.
I have noticed that my rear passenger brake drum assembly squeaks when I let off the brake pedal. Note that this is not noise when applying brake pressue, but after releasing the brakes. Additionally, the drum happens to be rusted very badly. It took a good amount of brute force to remove the drum in order to inspect the brake assembly. There was a lot of brake dust built up and I thought that cleaning that out would get rid of the noise.
I suspect it could be one of the springs but I cannot be for certain. The squeak does not occur when I release the parking brake.
Prius C :: 2012 - Revving Noise When Releasing The Accelerator
I've had my 2012 PriusC for about a year now and I'm loving it. As of a week ago the car has started doing this revving thing. I notice that the engine seems louder when I'm accelerating and it seems like I'm getting 30-40mpg instead of the usual 40-50 in cities (but it might just be me).
What worries me is that when I'm driving and I push on the pedal to accelerate, after I release the pedal there is a very loud whirring sound of the engine. It sounds like a MuscleCar or Racecar that is revving it's engine but not going anywhere. This sound happens if I accelerate lightly or severely and the revving sound is louder the harder I accelerate. I notice that if I accelerate and then ease off of the gas slowly, I don't hear the revving sound.
I notice that this seems to happen randomly, as in I start the car and it happens from the start, or I start the car and it doesn't happen at all for that drive.
Ford - Fusionhybrid :: 2012 - Engine Idles High After Releasing The Gas
My 2012 Hybrid engine will idle up after releasing the gas. The engine is sufficiently charged when this happens.
View 3 RepliesAccent MC (2006-11) :: Low Tone Engine Noise With Clutch Out, Becomes High Pitched With Clutch In
I've got an unknown issue with my 07 Accent (1.6L):
There is a low tone noise coming from near the upper area of the engine. It sounds like air or fluid traveling through a hose. The tone of the noise has recently become progressively louder, so that it is noticeable over normal road noise when driving. The noise does not fluctuate in tone or intensity with changes in RPM. However, the tone changes to a higher pitched frequency, almost like a hiss, when the clutch is fully engaged and held to the floor, both when in gear and when not in gear.
What the cause may be? And potentially required maintenance?
Chevrolet - S-10 :: 1995 - Temp Gauge Climbs To About 215 - 230 Within 10 Minutes Of Driving
I have a 95 s10 4.3L V6 auto with 92k miles.
This all started when one day on my way to work the temp gauge got to 260 then quickly fell. It has not gotten that hot since then.
When I start the truck cold and start driving, the gauge climbs to about 215-230 within 10 minutes of driving. Once the gauge hits what ever is the magic mark for the day it quickly falls (10 seconds or less) to about 170-180. Sometimes it will "cycle" up again to 200 or so then fall back to 170-180. Once it is done moving around it stays low and will not move much as I am driving.
I bought an IR thermometer and measured the temperature at various points in the cooling system. The top of the thermostat housing is about 195 or 200 right after it climbs and drops. If I drive for a while around town then check it, the housing reads hotter, about 220 max.
There does not seem to be enough temperature drop across the radiator, I have measured about 15 degrees difference max between the hoses and on some days only 10 degrees difference.
I have replaced the fan clutch (was bad or going bad), the thermostat, and the radiator cap.
After none of this fixed it, I took it to a mechanic who did a "block test" at my request and said it was fine. He thought what it was doing, climbing and falling was normal.
If I run it without the radiator cap on I do not see much if any flow when I look down into the radiator.
Right now I am thinking of doing the water pump and flushing the radiator this weekend.