Accent MC (2006-11) :: Clutch Slipping / Revs High While In Gear Without Accelerating Especially In 5th Gear
I've got a 07 accent with 90k miles on it. It has recently started slipping some (revs high, while in gear, without accelerating, especially in 5th gear). It also can be physically hard to move the shifter into gear sometimes (with my hand).
So, does this mean I need a new clutch? Or are there other possibilities? Should I replace/fix anything with the clutch? Sounds like the flywheel should be resurfaced? Will it shift more smoothly after the fix?
Is this something a newb could do himself? I can change the oil, rotate tires. Outside of that I haven't done much. My toolset for now is fairly limited: two jackstands, a trolley jack, torque-wrench and ratchet sets.
Accent MC (2006-11) :: Chirping / Grinding Noise In 3rd - 5th Gear And Only For First 15mins Of Driving
2007 Manual - I am getting a chirping noise/grinding noise. It happens in 3rd-5th gear and only for the first 15mins of driving. Stops making the noise after that. It happens sometimes when releasing the clutch pedal. Sometimes it occurs while accelerating and not touching clutch pedal at all. That mostly happens in 5th gear around 60mph. Thinking it has to do with trans, possibly throw out bearing. Not sure though.
View 13 RepliesAccent MC (2006-11) :: Low Tone Engine Noise With Clutch Out, Becomes High Pitched With Clutch In
I've got an unknown issue with my 07 Accent (1.6L):
There is a low tone noise coming from near the upper area of the engine. It sounds like air or fluid traveling through a hose. The tone of the noise has recently become progressively louder, so that it is noticeable over normal road noise when driving. The noise does not fluctuate in tone or intensity with changes in RPM. However, the tone changes to a higher pitched frequency, almost like a hiss, when the clutch is fully engaged and held to the floor, both when in gear and when not in gear.
What the cause may be? And potentially required maintenance?
GTI 337/20th Anniversary :: Clutch Grinding When Go Into Second Gear
So I am pretty sure its my clutch that is the problem, here's what happens: When I go into second gear, it doesn't really grind.. but its tough to get it into gear and its only with second gear. sometimes it will go right in and others i have to double clutch. when i double clutch it goes in smooth every time. now I don't think it would be syncros because I am pretty sure if it was that it would do it every time I shift? It only does it while its cold or hasn't been drove in awhile.. but after i drive it around its fine so I am pretty sure its the clutch. Second thing, what is an upgraded clutch that is good for these 6 speed transmissions?
View 2 RepliesGTI 337/20th Anniversary :: No Clutch When Going To Put Car In Gear / Just Grinding
I just put a stage 1 clutch in my 20th anniversary. When i was taking the transmission out, i dropped the hydraulic clutch line and all of the fluid spilled out. I got the whole thing done, and bled the clutch line and topped off the reservoir. I started the car and the clutch pedal had, what felt like the right amount of pressure. More than the stock, but not significantly. When i went to put it in gear, its like there is no clutch, just grinding and it doesn't go in to anywhere. I can cycle through the gears with the car off and like i said, the clutch has the right pressure and everything.
View 10 RepliesGolf/GTI VII :: 1st To 2nd Gear Grinding When Let Out The Clutch Pedal At Any Speed
MK7 with 15k miles... This morning on my commute into work, I started having some clutch issues. When I would try to go into 2nd gear from 1st at any speed, it would grind when I would let out the clutch pedal. It was like it didn't fully engage and if I pushed the pedal back in and tried to get it in 2nd, it would grind. All other gears were fine. I don't drive the car hard so I don't think I torched the clutch.
Synchros? Shift Alignment if these models have that? Pressure Plate?
Accent LC (2000-05) :: Light Grinding Noise When Let The Clutch Out / Pedal Super Hard
Yesterday I was driving home and my clutch started acting up. To start I was unable to press the pedal. The pedal was super hard, then let up but didn't feel right.
I removed the slave and the pedal went down fine. Both the master and the slave have no leaking and fluid levels are good. I haven't been able to have a buddy look at the levels when I press the clutch, but....
Here is a little more, the car shifts fine with the car off, it goes into all the gears, but with the car on it will not shift into gear. Also there is a light grinding noise when I let the clutch out..
I ordered a clutch kit already, but don't want to pull the trans if I don't have to, I would love to hear the issue is with the master or slave.....
2005 Hyundai accent with 138,000 miles
3000GT/Stealth :: Grinding When Shift Into Reverse And Car Won't Go Into Gear
Buying a vr4 this weekend with dr650 turbos... The only problem with car is when you shift into reverse it grinds and won't go into gear, I'm thinking its the reverse synchro?
View 2 RepliesAccent LC (2000-05) :: 2004 - Clutch Lost All Resistance / Hard To Get Into Reverse
I'm not very mechanical when it comes to cars. I have never had any clutch issue with my car. I arrived to work yesterday fine. When I started to leave it was incredibly hard to get into reverse and I had to force shifting after I left and the clutch had also lost all resistance and I could easily push it all the way to the ground. What could be a cause of the clutch always working perfect including the last time you drove it, and then 8 hours later you start up and it has done a 180. The fluid level is fine. I would presume if my clutch had went I have have slowly noticed it going.
View 1 RepliesFord F-150 - 1997-2003 :: New Clutch - Grinding Noise When Putting It Into 1st Gear
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission. I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced. I have also just had a new hydraulic clutch kit installed.......
View 1 RepliesElantra XD (2001-06) :: 2002 - Grinding Noise On Reverse Gear
My car has been making this grinding noise for the last 2 months. It happens when I put the car in reverse gear and slowly release the clutch. Rarely happens also in 1st and 2nd and 3rd and is always at the beginning of the transition when I am letting the clutch go. I do not know if it is the transmission, the clutch or any other part. I drive a 2002 Hyundai Elantra 5 speed manual transmission with over 120 k miles
Here is a link to a video I posted so you can hear the noise it makes : [URL] ....
GTI 337/20th Anniversary :: Clutch Not Working / Grinding Type Noise And Doesn't Go Into Gear
So I picked up a 20th today. The clutch has 30k on it its an oem luk. Drove fine most of the ride home then i went to shift and it wouldn't grab. Got it towed home. trans goes into all gears fine. When you put it in first and try to go it starts to roll but just makes a grinding type noise and doesnt go into gear. I didn't hear any chatter until maybe 10 miles before this happened. I still have pressure in the clutch pedal as well. when the car is in neutral running there isnt any noise which makes me think it isnt the throw out bearing.
View 2 RepliesPassat (B6) :: Clutch Clatter / Chatter Noise Either In Reverse Or In First Gear
When I have the clutch depressed and start to let out as I'm either in reverse or in first gear it makes a clatter/chatter noise. It also occurs when I have the clutch depressed and just rev the engine and it's in neutral. Some days it's louder than others. It doesn't matter if the engine is cool or at normal temp.
View 7 RepliesFord - Ranger :: 2009 - Clutch Sticks In 1st Gear And Reverse
I have a 2009 stick-shift 4WD ford ranger with a clutch that is sticky in 1st and reverse. Basically it requires alot of force to push it into 1st or reverse, but this problem isnt always there, and it the problem dosnt seem to pop up under any particular circumstances - e.g.: the weather, if the tuck has been driven recently etc. I paid $5000 for extended warranty when i bought this truck new, and the dealer repair shop tells me that they can't tell me if it is covered under warranty until they take it apart to see if the problem is a "wear item" .
If it's not covered under warranty then I am stuck with the $700 bill. Otherwise the truck runs great, and I have never had any work done under the extended warranty. The warranty runs out soon, and I am wondering whether to take a chance with a rebuild. My wife dosnt like to drive the truck with the clutch like that because she is afraid of getting stuck at a stoplight and being unable to engage the gear.
Nissan - 300zx :: Clutch Pedal Very Hard And Cannot Put It In 1st And Reverse Gear
I have a 89 nissan fairladyz32 (300zx) and when i push the clutch peddle in it is very hard and i cant put it in 1 and reverse when it is running but when it is off i can just fine. but then if i put it in 1 gear before starting it and push the clutch in to start the car it lurches forward a little what could this be? and when i leave it to idle for to long it puffs smoke or at first start up? It has about 80,000 km.....
View 6 RepliesAccent LC (2000-05) :: 2003 - Grinding When Shift From 1st To 2nd Gear
Why my car is grinding gear when I shift from 1st to 2nd, & yes the clutch is fully depleted and still grinds when I shift.
View 4 RepliesPassat (B6) :: Reverse Jumping Out Of Gear / Loud Grinding Noise And Pops Back In
I have a problem with my reverse in a 5 speed 105 hp Tdi. It jumps out of place when i try to move the car, makes a loud grinding noise and pops back in, I'm guessing the selectors are worn or maybe the teeth are too. My question is, how hard is it to replace the selectors (if it is the selectors that are worn of course), what is the cost of getting it done in the shop and most important does this sign mean I will have the same problems with the rest of the gear in nearby future?
View 2 RepliesAccent LC (2000-05) :: Car Doesn't Want To Go In Reverse And 5th Gear
Just bought a 01 Accent hatch the other day. It's a 5 speed 4cyl. First gear through 4th have no problems. If I try to shift into 5th gear or reverse, the car doesn't want to go into them. The dealer I got the car from said that the problem is with a pin or something. I have never bought a Hyundai before this, I've had old 70s american cars. I was thinking it could be a shifter linkage but I figured I would ask you knowledgeable people about it first before I go and break something trying to fix something simple (hopefully simple.
View 8 RepliesNissan - Versa :: 2007 - Clutch Feels Loose And Slight Grinding Sound When Shifting Only From Neutral To First Gear
Still chugging along!!
So, I haven't been the kindest car owner to my poor little hatchback. I do my best to get regular oil changes, but other than replacing the brakes last year, I have not kept up with most of the manufacturer's suggested regularly scheduled maintenance. The car has about 130,000 miles. Manual Transmission. My clutch feels a little loose, and I have been noticing a slight grinding sound when shifting (only from neutral to first gear).