Accent LC (2000-05) :: 2004 - Lost Reverse And All Gears Aside From First
I have the opportunity of getting i believe a 2004 accent gt for next to nothing. It recently lost reverse and all gears aside from first. The codes it is triggering are p0734 p0732 and p0733. Prior to throwing the codes it moved back but wouldn't budge forward. With codes no reverse or any gear higher than first. Car has 160k miles I am pretty mechanical. Should I run from this "cheap" "gas saver" or pick it up? With all 3 codes could it be just that sensor?
View 6 RepliesAccent LC (2000-05) :: 2004 - No Reverse / Shifts Hard Into Drive
2004 accent had a drink spill on lower console, and think this is why it quit shifting? Disassembled, cleaned switches, unhooked battery, and car still has no reverse, shifts HARD into drive, will not move further.
View 5 RepliesAccent LC (2000-05) :: Need To Push Clutch Really Hard To Allow The Gear To Engage?
2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).
Accent LC (2000-05) :: Light Grinding Noise When Let The Clutch Out / Pedal Super Hard
Yesterday I was driving home and my clutch started acting up. To start I was unable to press the pedal. The pedal was super hard, then let up but didn't feel right.
I removed the slave and the pedal went down fine. Both the master and the slave have no leaking and fluid levels are good. I haven't been able to have a buddy look at the levels when I press the clutch, but....
Here is a little more, the car shifts fine with the car off, it goes into all the gears, but with the car on it will not shift into gear. Also there is a light grinding noise when I let the clutch out..
I ordered a clutch kit already, but don't want to pull the trans if I don't have to, I would love to hear the issue is with the master or slave.....
2005 Hyundai accent with 138,000 miles
Accent LC (2000-05) :: Overheating Constantly - Car Won't Go In Reverse And Has Hard Time Shifting Sometimes
I have a 2003 Accent and it has been over heating constantly for about 5 months. After it started, we replaced the main radiator hose, thermostat, radiator cap AND a head and head gasket. It worked for about 2 weeks and then over heated again. It seems like there is too much pressure somewhere because the lid for my reservoir shoots off and all the coolant comes out. I'm just not sure where to look for a clog since it is coming out of the reservoir. It also recently started having transmission problems(?) or that is what I think it is... It won't go in reverse and has a hard time shifting sometimes. I'm not sure if it could be related or if it is the tranny also.
View 4 RepliesAccent LC (2000-05) :: Gear Stick Is Floppy - No Resistance In Gearbox
l got a problem with my 01 hyundia accent I have no gears at all,the gear stick is floppy. I have looked at the linkage from the stick to the gear box it's all ok but as it enters the box it has no resistance. The clutch is about 1year old.
View 2 RepliesAccent LC (2000-05) :: Crank Position Sensor Shows No Resistance When Cranking
I'm working on a family members car. We pulled out the old motor and put in a new one because the old one has rod knock. We're not getting ANY spark. Crank position sensor shows no resistance when cranking. The harness at the crank position sensor shows no voltage. The both coils measure 1.5ohms.
The only two bits of the harness that are in questionable locations are the grounds next to the ignition coil and the passenger side strut tower ground. I have the strut tower one to the closest bolt on the intake manifold and the coil pack grounds to the coil pack bracket.
The car has plenty of fuel and good cranking speed, just no spark. I verified using a timing light (no flash) and spark-plug short-to-ground. The old engine WAS running and all of the sensors on this one were swapped over from the running one. Also, the tach doesn't move when cranking.
Is there something that's commonly overlooked, or something that could be causing the issue searching showed it could be the crank position sensor, but like I said, I pulled the working one off the running engine.
Nissan - 300zx :: Clutch Pedal Very Hard And Cannot Put It In 1st And Reverse Gear
I have a 89 nissan fairladyz32 (300zx) and when i push the clutch peddle in it is very hard and i cant put it in 1 and reverse when it is running but when it is off i can just fine. but then if i put it in 1 gear before starting it and push the clutch in to start the car it lurches forward a little what could this be? and when i leave it to idle for to long it puffs smoke or at first start up? It has about 80,000 km.....
View 6 RepliesFord Ranger / B-Series :: 2000 - Reverse Lost After Harsh Thud
I have a 2000 Ranger 3.0 4x4 with over drive. When backing out of my driveway there was a harsh "thud" (for lack of a better word) and I lost reverse. The forward gears are still working. We pushed it out on to the road and I drove to my place of business. At that time reverse worked again. It only lasted a couple more times. Still have the forward gears. Could it be a band or clutch?
View 9 RepliesAccent MC (2006-11) :: Clutch Went Out - No Reverse / Goes Into 1st Gear After Lot Of Coaxing And Grinding
Ok, so I got my car at 60k miles, and the clutch went out almost instantly so I had the entire clutch replaced, and it was working just fine until now. It has been 25k miles since I did the full clutch replacement so it shouldn't be messing up again already. It is not going in to reverse at all, it goes in to 1st gear, but only after a lot of coaxing and grinding, and the clutch feels strange. The clutch is too soft (too easy to push down), but after a while it seems to get better.
2007 Hyundai Accent GS
Manual, hatchback
85k miles
Ford Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Accent LC (2000-05) :: 2003 - Lost The Ability To Shift Out Of 2nd Gear
My 2003 made a sharp mechanical noise one day, next thing I knew it lost the ability to shift out of 2nd gear....Now, it can still shift into 2nd gear when cold, but only after holding rpm for a bit and then suddenly jerking into 2nd gear. Once it's warmed up for a few minutes though, after dropping out of 2nd gear, that's it! Then it's stuck in 1st gear the rest of the time. Reverse doesn't work anymore at any time, and it gave me code P0732 to P0734 which should be gears 2 - 4. Is it possible that not being to get out of 1st means 2nd gear is broken, but the other 2 are okay and it just can't get shift past 2nd? Or might all 3 have problems after all?
View 1 RepliesAccent LC (2000-05) :: Idle Speed Lost And Engine Stops
Sometimes I loose the idle speed and the engine stops when I stop the car but it could be started again with full throttle it doesn't happen always it happens from time to time > I changed the MAP, IS actuator and TPS .The fuel pump and filter is new .In rare cases engine stops during driving. How about flash programming the ECU
View 1 RepliesAccent LC (2000-05) :: Lost Power Then Died While Driving / Now Will Crank But Not Starting
I have a 2005 hyundai accent (manual) with 140k miles on it that just broke down on me. I was driving to work and after about 10 minutes of driving I go to pull off my exit and I feel it for the first time, my rpms stay steady but the power drops for a few seconds before returning to normal. About 5 minutes later I'm putting around the parking lot and it's having trouble accelerating and reving to the point that it won't really move. I push it to a spot and let it sit for 5-10 minutes before starting it back up in an attempt to get it to a gas station to try and add fuel (quick Google search makes it sound like a fuel pump and the tank is pretty low). It accelerated in fits and makes it about two blocks feeling anemic. Oil changed about 2k miles ago (but is below the L mark on the dip stick when I just checked. I never see leaks though)
The engine ran and idled beautifully before this. No CELs.
Replaced the fuel pump. However, when I opened the port to the fuel pump assembly, there was almost no gas. So I think I might have just run out of gas and the problem was with the gauge.
Now it won't start with ~4 gallons in the tank.
I know the pump functions because I've pulled off the output tube at the pump and it'll spit out gas.
I know there's gas in the fuel rail because I pulled off the input hose.
I pulled off one spark plug to check for spark and it appeared to work.
I checked the resistance at 3/4 of the fuel injectors and they were within spec.
I've checked all the fuses.
I don't get any codes from OBD scanner I borrowed from Autozone (I've disconnected the battery a couple of times though)
I don't have a way to hook up the fuel pressure gauge I borrowed form Autozone because I don't have the adaptor.
Minus the clutch, I've done basically all maintenance myself, although certainly not a great mechanic.
Passat (B6) :: 2006 - Clutch Pedal Have No Resistance?
I have a co-worker that is having trouble with his 06 passat. He explained that the clutch pedal has no resistance and is on the floor. The dealer he took it to is saying he needs a new clutch and pressure plate claiming that the "pedal doesn't have pressure on it is because the clutch discs won't engage" which sounds backwards if you ask me. Anyway, what could this be? Where could we start tracking this down?
View 13 RepliesAccent LC (2000-05) :: Power Steering Lost After Cold Start / Came Back After Car Gets Warm
This problem has plagued me for a while(since last year). When I start the car in the morning, there's a brief period when the power steering is totally gone. When the car is thoroughly warmed up(after 2 minutes of driving), the power steering is back and there will be no problem. Wondering what could that be. The power steering fluid level is normal.
View 5 RepliesPassat (B6) :: Car Seems To Have Resistance When Shift To Reverse
Just bought my '07 Wolfie a couple of weeks ago. This is the first car I've ever owned with an automatic trans. I park in my driveway which is at a slight incline, and when I shift to reverse to pull out, it seems there is much more resistance than there is when I'm just parked on a flat surface. I do not normally use the parking brake, but even if I do there is still the same amount of resistance when shifting to reverse after I release it. I
I've read so many horrors about the push button parking brake I'm really hesitant to use the thing for fear it will break.
Passat (B5) :: Clutch Fell Straight To The Floor With No Resistance
I have a 2001 Volkswagen passat glx and last week I jumped in and hit the clutch and it fell straight to the floor with no resistance and i barely touched it.... What this means and if i can fix it myself instead of taking it to the dealership ?
View 4 RepliesPassat (B5) :: Clutch Pedal Gave Out And Dropped To The Floor Without Resistance
Last night I was driving home and decided to show off at a light. I punched it pretty hard, but it wasn't anything outrageous.. anyway, as soon as I shifted to second, my clutch pedal gave out and dropped to the floor without resistance. I coasted it to a gas station, luckily.. When I lifted my foot the pedal rose back slowly. I tried pumping the pedal, didn't work. I looked for leaks, but none were found. I turned it off, put it in first and tried starting it, and it turned over and jumped/jerked forward, a lot like it did right when I shifted into second and it went out. So I'm assuming that its not the entire clutch cause it wouldn't have engaged the engine. It's not a leak. pumping it didn't work so it's can't be a pressure issue.. what is going on? is it my master cylinder, or maybe my slave?
View 7 Replies