GTI 337/20th Anniversary :: Clutch Sticking When Released And Gears Only Engage When Push Hard Shift Knob
Been having trouble shifting into any gears on these chilly mornings in VA now... The clutch has been sticking on its way out when I release it and the gears don't want to engage unless I really push hard on the shift knob.
View 11 RepliesAccent MC (2006-11) :: 2010 SE Grinds When Shift Into Reverse
I've had my new left over 2010 SE for couple weeks now. done 600 miles.
I noticed at first a couple times when shifting from 1st to reverse while parallel parking and still slightly rolling forward, the the gear grinded a bit, despite the clutch being fully depressed. I figured maybe with this manual tranny compared to others i've driven that you just have to be dead still before shifting into reverse.
But then yesterday morning from my driveway, from a standstill I shifted into reverse and it grinded too, again with the clutch fully depressed. Is this normal with these cars? I've driven manual gtis and a ford focus and never experienced this before? Is this a problem?
the fact that it's happened three times now within a couple weeks tells me it's not me being sloppy on the clutch, it is definitely grinding with my foot all the way down on the clutch.
Golf/GTI VII :: Vibration Or Feedback In The Shift Knob When Shifting Into Reverse?
Is it normal to occasionally feel a little vibration or feedback in the shift knob when putting the car into reverse? It happens whether the car is in the "Warm-Up" phase or not, and seems pretty random. Happens about 25% of the time. It doesn't last but a tenth of a second, and it just barely makes an audible noise when the window is rolled down. This is my first manual transmission car so I just don't have the experience to 'diagnose' this. And no, I'm not trying to put the car in reverse while the car is still rolling forward.
VW Golf 5-speed....
Accent RB (2012+) :: Removing Automatic Shift Knob?
How is this done?
View 5 RepliesAzera TG (2006-11) :: How To Remove Gear Shift Knob
How Do You Remove Gear Shift Knob For Replacement ?? On My 07 Azera
View 2 RepliesAccent MC (2006-11) :: Blower Fan Keep Blowing When Fan Knob Set At 0
Accent 2009:
1. Blower fan keeps blowing when fan knob set at 0. It does turn off when key is off. Is that normal?
2. Low, high, washer, rear...all works, but Intermittent wiper setting doesn't work. Where do I look fuse/relay/switch itself...?
Accent MC (2006-11) :: Hatchback Trunk Door Knob Failure
I have a 08 Accent Hatchback. The trunk door knob(the black plastic hinge thing which you pull to open the trunk, not sure if I call it right) does not reset. I mean after pulling it to open the trunk, it's stuck instead of going back. I need to press it to original position, so the trunk door can be locked. I can see a rusty spring behind the black piece of plastic. Not sure where is the problem(maybe the spring?). How can I fix it.
View 20 RepliesFord F-150 - 1997-2003 :: Starter Engage The Flywheel But Couldn't Turn It Over At All
After getting the oil changed in my 1997 Ford F-150 4.6L with 150K miles at a local quick lube, I made one stop and my truck wouldn't start. I could hear the starter engage the flywheel, but couldn't turn it over at all. Oil was clean and full. I bench tested the starter and it tests good. I put a breaker bar on the crankcase nut and I could barely move it. Oil level was about 2 quarts low before oil change.
View 10 RepliesAccent MC (2006-11) :: 2nd And 4th Gear Hard To Engage
I own a out of warranty 2008 Accent manual, now on 94 000km/58 408 miles. This morning, it started to not engage 2nd gear, then when I press the pedal hard it does, then sometimes 4th gear. What could be at fault here, and how do I fix it?
View 9 RepliesAccent LC (2000-05) :: OBD2 Scanner - Couldn't Connect ECU
Today I bought an OBD2 scanner and was trying it on my 2001 accent but the app on the cellphone ( torque ) said : " couldn't connect ECU " . I think there is no ECU in my car, any example about trying the OBD on a 01 accent ?
Link to OBD2 : .........
Accent MC (2006-11) :: Hydraulic Assist Moving The Fork But Gears Just Won't Engage
2008 Accent - driving down highway, heard a pop and car acted like it was in neutral. I have clutch pressure, you can see the hydraulic assist moving the fork, but gears just wont engage. I can free shift through all the gears with the clutch pushed in or not. Manual transmission and clutch kit replaced about 6 months ago when shifting fork broke inside last transmission and tore it all apart. With car in first (and turned off), I can push the car so I know gears are not engaging.
View 6 RepliesPrius (Gen 2) :: 2006 Will Shift Into Neutral But Not Drive Or Reverse
Vehicle was repaired after front end collision and I get no codes found on scanner, had some bad connectors which I replaced and codes went away. I don't get ready light and the dash lights do not cycle off (ABS, SRS, Check engine, Etc. Etc.) The car will shift into neutral but not drive or reverse. Has new Aux battery and Hybrid battery is showing two bars. What to check ?
View 6 RepliesTouareg :: How To Take The Shift Knob Off
First the wife crushes the underbody on a huge rock cutting a corner. Now she spilled a whole pop down the shift lever, and its glued shut - it will hardly move. I know how to get the console off, but How do I take just the 'shift knob' off? I need to get the flexible piece underneath it off so we can wash all the parts.. I have the upper console part off.
View 11 RepliesGolf IV / Jetta IV :: Reverse Won't Engage Reverse After Transmission Replacement
I got a 99' Jetta gls 5 spd. I just replaced the transmission and now the car won't engage reverse from inside the cockpit. Reverse can be engage from inside the engine bay, but when the shift knob is depressed nothing happens. Linkag cables are in the correct spots.
View 6 RepliesGolf/GTI VI :: Shift Knob Broke Off
The other day the plastic top piece of my shift knob broke off (that had the shift pattern painted on it) and it made me once again want to replace the stock shift knob. I was considering buying one, but other than TWM I can't find any that I really like, so I want to machine one myself. My biggest problem in planning right now is what metal to use, SS is nice but expensive, and how to attach it to the leather and the stick. The only way I can think of attaching it to the stick is with set screws which would be hard to drill.
View 1 RepliesGolf IV R32 :: Shift Knob Jolts On Its Own
This has been bothering since the day I got my R. When im in 6th gear and let off the throttle I notice my shifter jolt a bit. Is this normal?
View 12 RepliesPassat (B5) :: V6 Shift Knob Is Cracking
I've got a 2001.5 v6 passat w/ auto and my shift knob has this cool burl veneer on it. I think it's real wood but it's pretty thin and it's got cracks on the front and the back. I can't see any simple way to remove the stick so that I can try to glue it. How to do that. But it's a standard tiprtonic shifter ... probably the standard on that model.
View 3 RepliesGolf/GTI VI :: How To Reinstall The OEM Shift Knob
I went to the golf ball, but I am thinking of going back to OEM. Looking for a heads-up about the process?
View 6 RepliesPassat (B7) :: DSG Shift Knob Removal
I am trying to remove the shift knob and the steps are entirely different than the DSG knobs from the GTI; You take just the boot off (not the assembly) then underneath is a hose clamp which needs to be removed. (this is not on the GTI version); I cannot figure out how to get this clamp off; I guess you need hose clamp pliers? And then do you need a new hose clamp? Won't it ruin the clamp?
View 24 Replies