Elantra MD (2010-15) :: How To Remove Manual Shift Knob
I have a 2011 elantra a 6 speed manual and im trying to take off the shift knob and can't seem to do it....
View 33 RepliesElantra MD (2010-15) :: 2013 - How To Remove Shift Knob
How do you remove the shift knob in a 2013 Elantra GLS? I didn't see a pin or anything.
View 3 RepliesPassat (B5) :: 2004 - How To Remove Shift Boot From Knob
I'm trying to swap out the shift boot of my 2004 (B5.5) Passat 1.8T 4Motion and running into trouble. According to the instructions from the new Red Line shift boot, I should be able to separate the two collars that hold the boot to the knob. However, the white post that's part of the knob assembly has a piece that's bigger than the lower black collar, preventing it from being removed. Is there something I'm missing? How can I remove the boot without damaging the existing knob assembly?
View 7 RepliesPassat (B5) :: 1999 - How To Remove The Stick Shift Knob
How to remove the stick shift knob on a 5 speed 99 passat .
View 3 RepliesElantra MD (2010-15) :: 2014 How To Remove Gear Knob
This car is an Australian 2014 Elantra SE
The existing manuals do not work, they show a knob previous to this one and don't apply.
Hyundai Elantra: Console. Repair procedures - Interior - Body (Interior and Exterior) - Hyundai Elantra MD 2010-2016 Service manual
Shows an earlier one and I can't find any other info.
Santa Fe (CM - 2007-12) :: 2008 - How To Take Gear Shift Knob Off
I'm new to this and not really sure if I'm doing it right. I need to know how to take the gear shift knob off my 2008 santa fe.
View 3 RepliesGrand Prix :: BTSI / Gear Shift Knob Removal?
I've tolerated having to release my key with the manual push button for years. Now the interior is disassembled (after replacing evap core) so I'm looking into fixing the BTSI.
I've never been clear on whether the problem is in the console by the gear shift or in the steering column. The thing is in the steering and has a solenoid that will mechanically allow the key to turn to the LOCK position when energized. The manual release is at the bottom.
I connected the leads of that white thing to battery voltage and sure enough, the post retracts. So that seems to work. However, when connected to the car wiring, there is not enough voltage to retract. It retract, it will hold. I concluded the problem is near the gear shift. Probing the lead (with the white thing disconnected) indicate battery voltage, but that's without any current.
Battery voltage is getting to the wiring harness in the console. Probing the leads to the Park switch indicates 90 ohms resistance. I suspect this is too high and causing a big voltage drop so there's not enough to energize the solenoid in the column.
What can be replaced in the console to remedy this? Is it only the park switch?
How is the gear shift knob removed? I see a slit in the back of the knob, but don't know how the mechanism works.
Santa FE SM (2001-06) :: 2005 - Gear Shift Knob Replacement?
How do I take off the gear shift knob? I want to replace it with an aftermarket one.
View 1 RepliesPrius (Gen 2) :: Shift Knob Making Click Every Time On Selecting A Gear
This morning the Shift Knob made a click every time I selected a gear, for about an hour, then it went away.
It was colder than almost ever here (Berkeley, CA) last nite, 30F. But there was no click back in '05 at 10F (in Prudhoe Bay, AK).
Mechanics (even the dealership!) say not to worry--probably a plastic part--just advised me to shift gently.
Azera TG (2006-11) :: How To Remove Rear Door Panels
I have a 2006 Azera and recently had the small part of the door handle fall off (part #83652E). I got a new part but wanted to know how easy it is to install this or whether I should have the dealer do it. Do I need a special tool to remove the door panel/clips or can I do it with something else. Once inside, is it just as simple as screwing the new part on through a hole in the door?
View 2 RepliesAccent MC (2006-11) :: Couldn't Engage Reverse When Put Shift Knob On
So I just installed my short shifter and everything works great, all the gears engage, however, when I put my shift knob on I noticed I couldn't engage reverse because it sits down too low and doesn't allow the reverse lockout to get over the rail and engage reverse. I have to loosen the knob so it sits higher and then I can engage reverse, but it moves around, so I can't leave it like this...right now my plan is to make some sort of spacer for the knob to sit on and then put loctite on it...seems like it would solve my problem. I have a Hyundai Aluminum shift knob and the short shift is OEM so I don't see what could be wrong ...
View 8 RepliesAzera TG (2006-11) :: Occasional Hard Shift While Accelerating From A Signal Light
On my 2006 Azera Limited with about 27,000 miles on it. Occasional hard shift issue. Normally the car is only driven 10 miles a day to and from work no problem. But on longer trips have hard a few instances of hard shift.
The first time this hard shift bump occurred was when I was driving on city streets 2 minutes after getting off the freeway after a 2 hour drive. On a scale of 1-10 this was a #5 bump like feel followed by a #3 bump in the next few minutes while accelerating from a signal light. There were no further bumps that day, even after another 2 freeway drive.
The second time the #3 bump happened was on an on ramp after a 3 hour freeway drive and a short rest stop. No further bumps that day even after another 3 hour freeway drive.
The last time this #3 bump happened was on a city street after a 45 minute freeway drive. No further bumps on the return trip. I am not sure which gears this bump happens between.
I have no MIL set. So I took it too a transmission shop and they could not find anything wrong but said there was a code C1616 CAN Bus Off Failure. His opinion was that this problem maybe an electrical issue.
Azera TG (2006-11) :: Hard Shifting From 2nd To 3rd Gear Only
So, I bought an used 2006 Hyundai Azera Limited few days ago. It's clean title and has 86k miles on it now.
After three days from the purchase date, my car starts causing transmission problems, hard shifting from 2nd to 3rd gear only. It's getting worse now...
Now, what should I do? ...
Azera TG (2006-11) :: Transmission - Clunk When Shifting From 4th To 5th Gear
2007 Azera 120k miles. Have noticed first thing in the morning when shifting from 4th to 5th gear, I hear a clunk.. Yesterday I heard two clunks when downshifting from 5th to 4th. Tried shifting the car manually today and was able to replicate the problem. After 15 minutes of driving, the problem is gone.Never seems to happen in the afternoon after car has been driven.Transmission fluid is full. Have always changed at the 60k intervals.Fluid is not burnt. Light pink color.
What could possibly be causing this? Is this likely to get worse? How long might I have before the car might become not drivable ? I ask this because I have been considering trading it in for a new car. Now seems to be a good time to buy a 2016 car, since the 2017"s are almost out.
Ford F-150 - 1997-2003 :: 1998 - Way To Remove Lumbar Support Knob?
I have a '98 F150 front 60/40 seat going into a '77 shortbox F100. I've searched and found a lot of info on repairing a lumbar support but nobody seems to mention how to get the stupid off. I don't want to break anything but I can't see any screws or clips. Does it just pull off with force?
View 1 RepliesTouareg :: How To Take The Shift Knob Off
First the wife crushes the underbody on a huge rock cutting a corner. Now she spilled a whole pop down the shift lever, and its glued shut - it will hardly move. I know how to get the console off, but How do I take just the 'shift knob' off? I need to get the flexible piece underneath it off so we can wash all the parts.. I have the upper console part off.
View 11 RepliesAzera HG (2011-16) :: Remove Map Prompt On Start?
Is there a way to remove the prompt on the map display on engine start?
View 15 RepliesGolf/GTI VI :: Shift Knob Broke Off
The other day the plastic top piece of my shift knob broke off (that had the shift pattern painted on it) and it made me once again want to replace the stock shift knob. I was considering buying one, but other than TWM I can't find any that I really like, so I want to machine one myself. My biggest problem in planning right now is what metal to use, SS is nice but expensive, and how to attach it to the leather and the stick. The only way I can think of attaching it to the stick is with set screws which would be hard to drill.
View 1 RepliesGolf IV R32 :: Shift Knob Jolts On Its Own
This has been bothering since the day I got my R. When im in 6th gear and let off the throttle I notice my shifter jolt a bit. Is this normal?
View 12 Replies