Accent LC (2000-05) :: 2000 - Misfiring Upon Acceleration And Engine Revving
I have a 2000 accent. Automatic tranny with 167000 miles. My current problem is the car is misfiring upon acceleration and engine revving. I have to accelerate very slowly to minimize this but i once the engine revs up enough I can give it more gas and it will rev normally with plenty of power. I have had to unplug the maf to keep it driveable. Ive never had a car stay running after disconnecting the maf so this is strange to me. My accent barely stays running with the maf connected. I just got the car from my dad and he had it fixed and it ran good for awhile with the maf connected so I don't think it is the maf. But the same problem came about and we had to disconnect the maf again. And he cant remember or is not sure what was exactly fixed on the car. I've read up about the purge control valve and havent had a chance to check it out but some of the symptoms fit.
View 21 RepliesAccent RB (2012+) :: Engine Revving Itself Higher The Second After Push The Clutch In
Today I started my car (in the garage so it wasn't too cold) and everything was fine. The car warmed up in a couple minutes and I was off.
As i was driving, I noticed that my shifting was horrible. It felt like i was burning the clutch and not releasing the clutch smoothly in general.
I then noticed that when i pressed in the clutch ready to take the next gear, the engine would raise the rpm's about 500-1000 revs before coming down.
I started to wait till the revs came down to shift and that seems to work.
Why would the engine be revving itself higher the second after i push the clutch in. My dealer can't take me until Wednesday so I don't know what to do.
Accent MC (2006-11) :: 2008 GS - Misfire On 3 Cylinders / Rough Idle And Poor Acceleration
After scouring through hundreds of threads on this forum (which is Awesome, BTW), it seems as if this misfire / rough idle thing is fairly common (which is scary!!). CEL is on steady. Had the codes pulled; P0301, P0302, P0303. At the recommendation of the mechanic, I had the plugs replaced...no improvement. He then replaced the ignition coils...no improvement. Just finished replacing the MAP sensor. This actually had a VERY temporary positive effect. However, after about 5 miles of driving, the misfiring returned. Took the car to the Hyundai dealership, and they acted as if they didn't want to fool with it. They referred me to a couple of local repair shops...????
View 8 RepliesFord - Explorer :: 2000 - Cylinder 3 Misfire Persistently / Engine Stumbles And Has Poor Acceleration
I have a 2000 Explorer 4.0 SOHC that I'm having a persistent problem of cylinder 3 misfire. I've changed plugs with Motorcraft plugs set to the proper gap, put on new wires and have checked the resistance across the ignition module, both primary and secondary without change. I doubt that the problem could be the ignition control module as only cylinder 3 is affected. I have Auto Enginuity that I use to read the codes, attempt a repair and then clear the codes only to have P0303 appear again. Obviously the engine stumbles and has poor acceleration.
View 14 RepliesAccent LC (2000-05) :: 2002 - Engine Revving On Its Own Occasionally
I got a 2002 accent 1.3 si, engine warning light comes on but doesn't seem to affect cars running, no misfires, no stalling, still good acceleration and mpg, occasional engine revving on its own, changed tps sensor and engine revving on its own was worse. Was told by hyundai mechanic to disconnect battery for 30 seconds and if light went out it was either faulty tps sensor or an intermittent non constant fault reading, light did go out for some time but is now back on.
View 1 RepliesAccent LC (2000-05) :: White Smoke Coming Out Particularly When Revving
I recently changed my Hyundai Accent 2004 rings and top cylinder. a day after I left the mechanic garage, the car started bringing out white smokes particularly when I rev.
View 2 RepliesAccent LC (2000-05) :: 2001 Almost Dies When Let Off Accelerator After Revving
I have replaced the MAF sensor, TPS sensor, and fuel filter. Like the title says...if I rev the engine ...as soon as I let off the accelerator the engine stumbles and almost dies...then settles back down. I initially pulled codes PO121 so I replaced the TPS. PO103 so I replaced the MAF sensor. PO112..did not address directly as I assumed the MAF was causing. PO1123...again I hoped the parts I replaced would solve the problem. Initially the engine would just drop out while driving just for an instant and then be fine...also I had the 4 codes mentioned above. The only code that has returned is the PO121. I just got done replacing the fuel filter and things seem to be worse.
View 1 RepliesAccent LC (2000-05) :: Gears Started Slipping - RPMs Kept On Revving Up
Just the other day I was driving my car till I've noticed the gears started slipping. At first it was having some issues shifting through the gears (automatic transmission btw). As soon as I got off the highway, I parked in a parking lot just to check underneath the hood. Everything looked fine, went to pull out of the parking lot, no reverse. The gears started to slip up really bad. I noticed that the RPM's kept on reving up and wouldn't go any faster than 20mph. I went to an advance auto parts to get automatic transmission fluid. Still having the same issue and no reverse either. I had to park the car at a location to get it towed back to my house. Some people are saying my transmission is bad, some say it could be a real simple fix. Where to start diagnosing this issue. The car was driving normally until last Monday. My question is where should I start to check and what can I do to see if the transmission is completely shot??
View 33 RepliesAccent LC (2000-05) :: Taking 5 Turns To Start - Engine Noise And Car Revving Itself
I have a 2000 model accent manual trans its just recently clocked 200 000 km I know the car has had problems but they are getting worse. Occasionally I have Problems starting the car in the past but it usually takes no more than 5 turns to get started but this is getting worse the other day it took about 5 min maybe more to get the car started I am guessing my starter motor probably Needs to be changed.
Next problem yesterday after I put a full tank of Premium 98 in the car its starts to rev itself changing the sound and note of the motor running constantly it has done this in the past but not so severely and It only seem to do so after putting petrol Especially when I put fuel From a servo I don't usually go to the car would have stalled more than once but didn't only because I tried to keep the revs up when it sounded like it was gunna die also I am pretty sure my fan was making some weird noises but the car has had no engine Light show and no Overheating.
Accent LC (2000-05) :: 2001 GL Started Revving When Driving During Traffic Hour - Transmission Slipping?
I have a 2001 Accent GL 1.6L Automatic.
Yesterday it started acting up on the freeway. I was driving about 50 during traffic hour when it started revving. I got off the freeway and moved to 35mph on surface streets, the revving continued at lower speeds but much worse (4-5k rpms going 10-15mpg). Doesn't seem to do it in idle or park. If i shut the car off it'll drive fine for a while then start acting up but when I was driving, after awhile, it did return to normal.
What could cause the problem? TPS? Transmission? Sensor of some sort?
Accent LC (2000-05) :: Clutch Grabbing When Engaged
I bought a used accent 1.3 before few months , with 100k miles on the clock. I did all the basic maintenance stuff, oils, filters, spark plugs, coolant, timing belt etc... I replaced the clutch disc also, because it was slipping.
The problem is that the clutch engage with a knock sound, just like when you have a loose engine mount. But... if i stay with clutch pedal pressed for a second, do the shift and released, the clutch engage smooth and all works fine. So, that's the way I do shifts for now.. Is this a flyweel problem?
Accent LC (2000-05) :: Stumbling On Acceleration
2002 accent 1.6 motor and 5 speed,when I take off the motor sputters for a moment then is fine and if I let it slow down in any gear and step down on it it will sputter again then is fine, so far I have changed the plugs and air filter cleaned the throttle body and MAP, the wires and timing belt were changed out not long ago, took it in and hooked the machine to it and it said misfire bank 1 oxygen sensor upstream so replaced it and still have the problem, the body has 200,000 on it and the motor 100,000.
View 8 RepliesAccent LC (2000-05) :: Clutch Makes A Hissing Sound
My clutch makes a hissing sound whenever i press it down while driving, its working fine, but am worried about the sound, i checked the master as well as the slave cylinder and there is no leak. Plus how do i remove the moisture from my headlamp.
View 3 RepliesAccent LC (2000-05) :: Air Conditioner Compressor Clutch Is Not Engaging
l have a 2000 model accent and the air conditioner compressor clutch is not engaging . you press the 'AC 'button and the indicator comes on when a fan speed is selected which l am sure is the correct operation.l checked for 12 volts at the coil terminals of the relay and there is no 12 volts.l shorted the switch contacts of AC relay and the compressor did engage so the wiring from the relay base to the the compressor clutch is ok. l also checked the contacts of the 'AC' switch itself and it seems to be ok. l haven't had much luck with sorting out the wiring from the switch to the relay as l do not have a wiring diagram.
View 4 RepliesAccent LC (2000-05) :: CE Light Came On - Sluggish Acceleration
I drive a 2001 Hyundai Accent. About a month a go the CE light came on. at first, the car was driving fine so I thought nothing of it. Then I started noticing that the acceleration was sluggish and when it finally accelerated, it basically slingshot forward. What could be wrong. There's no smell, rattling or anything else. The only thing I noticed was the engine was a bit louder.
View 1 RepliesAccent LC (2000-05) :: Motor Struggling From Low RPM Acceleration
My problem is this: when I am driving and press the throttle hard from low rpm (anything under 2000-2500), the car will struggle to pick up rpm, and be incredibly sluggish to accelerate, until it reaches around 3500 rpm, at which points it returns to normal. Whilst it is struggling to accelerate, the exhaust sound is almost like a subaru, in that there is a series of small burp noises which stop once it returns to normal acceleration. It only whilst attempting to accelerate from low rpm that I have this problem, i.e. idle plus mod-high rpm is fine.
View 2 RepliesAccent LC (2000-05) :: Need To Push Clutch Really Hard To Allow The Gear To Engage?
2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).
Accent LC (2000-05) :: Transmission Stuck After Changing Clutch And CV Axle
I have a 2000 Accent that I changed the clutch and CV Axles on and now the transmission seams to be stuck. When i got done replacing the axles and installing the brakes I spun the wheels while installing the nut to aline the cotter pin. Once I got the car down, serviced the gear oil, bled the clutch master. Went to drive the car and it wouldn't move .
View 5 RepliesAccent LC (2000-05) :: Stalls In Neutral When Clutch Pedal Released
I have an 00 Accent 1.5 liter 5 speed with about 192000 miles on it. I have put about a tank of gas through it since I've owned it, so I can't give a lot of background on it. When I got it the previous owner told me it was popping out of fifth gear and the clutch fluid leaked.
Upon driving it around a while I noticed it would pop out of fifth and third gears almost at random, but seemed to happen more when I applied throttle. I assumed it was an issue with the shifter not fully engaging the gears, and checked out the bushings under the hood and in the console. All looked good, and I didn't see any extra play.
I drove the car for about 30 miles straight and had to downshift and wasn't able to get the car to go into any gear but fifth. I was moving about 20 mph when this occurred. I was able to limp along to a parking lot where I let the car sit for about ten min and I shifted through the gears when stopped. I headed back home with this problem throughout the trip. There is a sound that happens on occasion (that stops when I press the clutch pedal) that sounds like a bad bearing in the clutch area.
When I'm stopped with the car in neutral and I release the clutch the car stalls like it's in gear. I was able to get the car to move some, but it really doesn't want to it acts like there is something jammed in the gears and popped really loud when I backed it up.
There is fluid for the master cylinder, and I can see the slave cylinder moving when the pedal is pressed. I jacked it up and removed the plug to check for gear oil, and it came pouring out, so I think it has fluid in the gearbox. I'm pretty sure it needs a clutch at the least. I think there may be some internal damage in the tranny, and I'm only into the car for the time it took to power wash a house and don't want to get involved in a big mess.