Golf IV R32 :: Clutch Pedal Not Grabbing Like It Usually Does
Ok so I took my R out to look track to get some 1/4mile passes in. Didn't do anything out of the norm. Took my first pass and noticed that much clutch pedal wasn't feeling right. It wasn't grabbing like it usually does, it was grabbing close to the floor. I took it out of gear and pumped the clutch peddle a few times and then it grabbed like it normally would. I've never had something like this happen in any of my VWs or any other car. What may have happened? I was thinking maybe a slave cylinder issue?
View 7 RepliesHonda - Prelude :: 1998 - Clutch Is Grabbing Very Low And It Does Not Slip
I am purchasing a car on eBay which was stated to have the following problem: "the clutch is grabbing very very low it does not slip i think it is just the hydraulics? ". When I asked if I would need to have it serviced in order to drive it 1500 miles back home ( which in my mind meant an oil change), their response was that I would need to have the master cylinder replaced in order to drive it that far...
View 13 RepliesToyota - Tacoma :: 2001 Bucks / Jumps Like Clutch Is Alternately And Rapidly Grabbing And Releasing
My 2001 Tacoma drives well most of the time, but when in 4 wheel drive low range, low gear, in demanding circumstances like heavy snow, it will buck, jump, act like the clutch is alternately and rapidly grabbing and releasing (but I'm pretty sure it's not actually that). Tires are good. Four cylinder, standard transmission.
View 7 RepliesAccent LC (2000-05) :: Clutch Makes A Hissing Sound
My clutch makes a hissing sound whenever i press it down while driving, its working fine, but am worried about the sound, i checked the master as well as the slave cylinder and there is no leak. Plus how do i remove the moisture from my headlamp.
View 3 RepliesAccent LC (2000-05) :: Air Conditioner Compressor Clutch Is Not Engaging
l have a 2000 model accent and the air conditioner compressor clutch is not engaging . you press the 'AC 'button and the indicator comes on when a fan speed is selected which l am sure is the correct operation.l checked for 12 volts at the coil terminals of the relay and there is no 12 volts.l shorted the switch contacts of AC relay and the compressor did engage so the wiring from the relay base to the the compressor clutch is ok. l also checked the contacts of the 'AC' switch itself and it seems to be ok. l haven't had much luck with sorting out the wiring from the switch to the relay as l do not have a wiring diagram.
View 4 RepliesAccent LC (2000-05) :: Revving With Poor Acceleration With New Clutch
I have just changed my clutch and machined my flywheel on my 1.5ltr 16v dohc 2000 lc accent. I used all the correct trans fluid and refilled and bled the clutch fluid. It takes of from lights like a new car but if you put your foot down around 40kph it revs out a bit and does so through all gears untill you reach a bit of speed. What is going on?
View 11 RepliesAccent LC (2000-05) :: Need To Push Clutch Really Hard To Allow The Gear To Engage?
2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).
Accent LC (2000-05) :: Transmission Stuck After Changing Clutch And CV Axle
I have a 2000 Accent that I changed the clutch and CV Axles on and now the transmission seams to be stuck. When i got done replacing the axles and installing the brakes I spun the wheels while installing the nut to aline the cotter pin. Once I got the car down, serviced the gear oil, bled the clutch master. Went to drive the car and it wouldn't move .
View 5 RepliesAccent LC (2000-05) :: Stalls In Neutral When Clutch Pedal Released
I have an 00 Accent 1.5 liter 5 speed with about 192000 miles on it. I have put about a tank of gas through it since I've owned it, so I can't give a lot of background on it. When I got it the previous owner told me it was popping out of fifth gear and the clutch fluid leaked.
Upon driving it around a while I noticed it would pop out of fifth and third gears almost at random, but seemed to happen more when I applied throttle. I assumed it was an issue with the shifter not fully engaging the gears, and checked out the bushings under the hood and in the console. All looked good, and I didn't see any extra play.
I drove the car for about 30 miles straight and had to downshift and wasn't able to get the car to go into any gear but fifth. I was moving about 20 mph when this occurred. I was able to limp along to a parking lot where I let the car sit for about ten min and I shifted through the gears when stopped. I headed back home with this problem throughout the trip. There is a sound that happens on occasion (that stops when I press the clutch pedal) that sounds like a bad bearing in the clutch area.
When I'm stopped with the car in neutral and I release the clutch the car stalls like it's in gear. I was able to get the car to move some, but it really doesn't want to it acts like there is something jammed in the gears and popped really loud when I backed it up.
There is fluid for the master cylinder, and I can see the slave cylinder moving when the pedal is pressed. I jacked it up and removed the plug to check for gear oil, and it came pouring out, so I think it has fluid in the gearbox. I'm pretty sure it needs a clutch at the least. I think there may be some internal damage in the tranny, and I'm only into the car for the time it took to power wash a house and don't want to get involved in a big mess.
Accent LC (2000-05) :: 2004 - Clutch Lost All Resistance / Hard To Get Into Reverse
I'm not very mechanical when it comes to cars. I have never had any clutch issue with my car. I arrived to work yesterday fine. When I started to leave it was incredibly hard to get into reverse and I had to force shifting after I left and the clutch had also lost all resistance and I could easily push it all the way to the ground. What could be a cause of the clutch always working perfect including the last time you drove it, and then 8 hours later you start up and it has done a 180. The fluid level is fine. I would presume if my clutch had went I have have slowly noticed it going.
View 1 RepliesFord A/C :: Clutch Always Engaged?
Just noticed that upon start up and idle ac blows ice cold. 5 miles down the road it starts to blow warmer. I've misplaced my manifold set. I did have a low pressure gauge from a long time ago.
Low pressure was would stay around 40psi then slowly over 5 seconds or so drop down to 20 hold for about 10 second and climb back up. All while just at idle.
That's after i added a can of refrigerant. After the second can it seems to have stabilized at around 40 psi. Which is still a little low for being almost 90* outside.
I know with just one reading its like reading a book and only reading every other page.
Here is my main question. Is the compressor suppose to cycle? I've always been under the impression it does. So i deemed a bad pressure switch possibly right off the bat. After doing a google search i see some are stating that it runs continuously.
The only time in a 15 min span my compressor kicked off is when i turned the control to "OFF" or when i unplugged the pressure switch. Is this right? Seems like i would burn up the compressor...
Accent LC (2000-05) :: Light Grinding Noise When Let The Clutch Out / Pedal Super Hard
Yesterday I was driving home and my clutch started acting up. To start I was unable to press the pedal. The pedal was super hard, then let up but didn't feel right.
I removed the slave and the pedal went down fine. Both the master and the slave have no leaking and fluid levels are good. I haven't been able to have a buddy look at the levels when I press the clutch, but....
Here is a little more, the car shifts fine with the car off, it goes into all the gears, but with the car on it will not shift into gear. Also there is a light grinding noise when I let the clutch out..
I ordered a clutch kit already, but don't want to pull the trans if I don't have to, I would love to hear the issue is with the master or slave.....
2005 Hyundai accent with 138,000 miles
Accent LC (2000-05) :: When Clutch Is In Gear Stick Will Not Move In Any Direction / Completely Stuck
Bought a 2001 hyundai accent 1.3 si petrol manual 2 weeks ago. After pulling off today, i went to go into 2nd gear, and I couldn't move the gear stick. I parked up and turned the engine off, then started the ignition again. When the clutch is in, the gear stick will not move in any direction, its completely stuck, but when the clutch is out, the gear stick will move in all directions.
View 6 RepliesAccent LC (2000-05) :: 2002 - Manual Trans Has Small Leak At Slave Cylinder For Clutch
So my accent with a manual trans has a small leak at the slave cylinder for the clutch. I am driving home and it's shifting hard. I get home pull up to where I live and push In the clutch and the car feels like the clutch is not pushed in. RPMs drop and car stalled. Look under hood and see not fluid in clutch master cylinder. Fill with fluid and pump pedal. I get some pedal back but the car will not crank. Nothing. I have accidentally cranked car when in gear in the past and there did not seem to be a safety switch as the car would move if my foot was not on brakes.
View 4 RepliesFord A/C :: 1999 F150 - Clutch Is Always Engaged
I bought a 1999 F150 4.6 4x4 recently that is giving me some problems. The current one is the AC compressor. The system wasn't charged when I bought it a month or so ago and last week the compressor started smoking. I replaced it with a brand new one, including the clutch and pulley, accumulator and orifice tube. I never got the chance to charge the system because the first time I drove the truck the new compressor started freezing up. I took it back and exchanged it and put the new one in. This time I paid attention and the clutch engages as soon as I start the truck. The AC controls are off and there is no freon in the lines.
View 10 RepliesGolf IV / Jetta IV :: 2003 GLI - Air Compressor Clutch Will Not Getting Engaged
I have a 2003 2.8 GLI and my compressor clutch will not engaged i provided the clutch with a direct power and ground from the battery and it engaged. i also went to the junk yard and got a couple of Fan Control Module ($4 each) and it still does not engaged.
View 3 RepliesPassat (B5) :: Clutch Engaged And RPMs Shoot Up Fast
Last week I took my baby to AWE Tuning, and had a chip and a diverter valve installed, when i left it felt like a different car it was great! now when im driving its not right, ok ill be in gear and as soon as i get on it and hit like 3thousand rpm it feels like the clutch is engaged and the rpms shoot up fast and the car isnt moving like it should. is it my clutch?
View 1 RepliesFord :: Clutch Slightly Engaged At Stop Light
So I've had a habit of slightly engaging my clutch at stop lights so that the transition to the gas is easier and quicker. Never had a problem until today where I smelt the dreaded clutch burn odor. I think I had it too engaged since it was sorta lugging at a standstill for a bit, but in general is this a bad idea? If I don't go as aggressive as the lugging feeling but slightly release it, am I doing damage?
View 19 RepliesElantra XD (2001-06) :: GLS Clutch Engaged And In Gear But Car Will Not Move
Here's the scoop: 2 year old clutch & flywheel with 21,000 miles on them. Clutch master cyl. is full & not leaking. The clutch slave cyl. moves when the clutch is pressed & is also not leaking. The shifter linkage has been checked at the shifter and moves freely as it should.
I started the car, put it in gear, let the clutch out and there is no movement from the car regardless of the engine revs. The engine runs freely and does not die with the clutch engaged and the transaxle in gear. Putting it in ANY gear (including reverse) has no effect. The car will not move.
After turning the engine off I left the car in gear, left the e-brake disengaged, released the foot brake and the car stayed put. I then put the shifter into neutral, let the foot brake off and the car began to roll. I stopped, put the shifter back into 1st, let the foot brake off and the car was again stationary and did not roll. This tells me that the shifter linkage indeed works and that the car WILL go into gear. So, why won't the car move under power?