Ford Super Duty (1999-2016) :: A/C Clutch Hardly Stay Engaged
I was thinking my AC clutch has too much gap and was gonna do the "fix it" listed in another thread. However, my clutch wouldn't engage like it states needs to be done. The only time my AC blows cold is when it's cold/cooler outside OR I rev up the RPM's but it hardly stays engaged. I had a friend do a few diagnostics on it, with a paper clip (assuming he did it right) he feels my clutch is bad. But I've read the clutch is either good or bad, works or doesn't work, no in between.
Next, it doesn't seem to blow as hard as it used to. I replaced the blower motor last summer, but even before that, it seemed to not blow very hard. If I have it on low, it's very hard to feel it. With a crew cab and 2 little boys seated in the back, they often end up sweaty and miserable, no matter how far we go. I've read the orifice tube might need to be replaced, or something needs to be cleaned cuz it's dirty or clogged like the orifice tube. But I can't remember what.
Ford Super Duty (1999-2016) :: A/C Clutch Staying Engaged - Compressor Burned
I need diagnosing why my A/C isn't working. I'm wondering if my clutch staying engaged has burned up my compressor before or after my clutch went bad. I don’t think it’s the air gap issue because I took my clutch off and checked and there were zero washers. I guess somehow I re-installed it with no washers maybe the last time I fooled with it.
I've only knew to check the air gap trick and when that didn't work, I wasn't sure what my next step could be. I tried looking at the high side pressure switch connector to see if it was burned up and it looked ok.
Can track down if my compressor is still good and replacing my clutch is the only thing I need to do or if I need to replace my compressor? Or if there's something else that's totally unrelated that I need to check?
Ford Super Duty (1999-2016) :: 2002 F350 - A/C Clutch Not Staying Engaged
So I have an 02 f350 and I just recharged the ac system today. At first the clutch wouldn't engage, I tried tapping it and nothing. Then when I went to pull it out of the garage I left it in park to close the garage doors and I could hear it locking and unlocking.
I checked the voltage at the plug and am barely getting half a volt but it still doesn't lock up when I apply direct power to it. I didn't mess with the shims because I do not believe that to be the issue.
After I had shut the truck down and started it back up the clutch wouldn't engage at all. Do I just need to run the system or what? Its working just not consistently, I was thinking the oil needed to be recalculated a bit.
Ford Super Duty (1999-2016) :: AC Low On Freon / Clutch Not Staying Engaged When Revved It Up In Neutral
So I've worked on this A/C for 3 years, I don't drive this truck very much or often, partly because the A/C doesn't blow cold. Its a 99 f250 7.3 ... Here's what I've done, first it was low on Freon so I added some and it got cold, take off driving and it gets hot. After some research I check the clutch air gap and pull a washer. This changes nothing, I put a valve on the heater core, so I could manually shut it off just in case.
This year I replace the compressor because the clutch isn't staying engaged when I revved it up in neutral. I went ahead and replaced the drier and Orifice Tube, the orifice tube was clogged up. So I start recharging the system, and I get 2 3/4 cans in and its blowing cold, low 50's high 40's its 75 degrees outside. The gauges read 35 low and 300 high, I'm a little confused cause it was suppose to hold 41oz from what I looked up but ok.
I rev the motor just to check everything out, the low side heads down for a second then starts going up, the high side starts going up and doesn't stop. The high side goes all the way till it hit the high pressure switch 450 wow. I'm thinking its over charged, I let it idle and the compressor kicks on and the low is around 50 and the high is at 350. So I rev it up again 1800 rpms or so, and the low side drops down and so does the high side. Except this time the low side drops down to 15 " I had the low pressure switch unhooked and looped" and the high side around 225.
Ford A/C :: Clutch Always Engaged?
Just noticed that upon start up and idle ac blows ice cold. 5 miles down the road it starts to blow warmer. I've misplaced my manifold set. I did have a low pressure gauge from a long time ago.
Low pressure was would stay around 40psi then slowly over 5 seconds or so drop down to 20 hold for about 10 second and climb back up. All while just at idle.
That's after i added a can of refrigerant. After the second can it seems to have stabilized at around 40 psi. Which is still a little low for being almost 90* outside.
I know with just one reading its like reading a book and only reading every other page.
Here is my main question. Is the compressor suppose to cycle? I've always been under the impression it does. So i deemed a bad pressure switch possibly right off the bat. After doing a google search i see some are stating that it runs continuously.
The only time in a 15 min span my compressor kicked off is when i turned the control to "OFF" or when i unplugged the pressure switch. Is this right? Seems like i would burn up the compressor...
Ford :: Clutch Slightly Engaged At Stop Light
So I've had a habit of slightly engaging my clutch at stop lights so that the transition to the gas is easier and quicker. Never had a problem until today where I smelt the dreaded clutch burn odor. I think I had it too engaged since it was sorta lugging at a standstill for a bit, but in general is this a bad idea? If I don't go as aggressive as the lugging feeling but slightly release it, am I doing damage?
View 19 RepliesFord F-150 - 1997-2003 :: Shifting Into Reverse - Clutch Not Engaged At All
Just got a 98 f150 yesterday and I noticed last night when I went to shift into reverse, with the clutch all the way to the floor as I tried pulling the shifter back, it sounded like the clutch wasn't engaged at all. Shifting from all the other gears works just fine. Ive found that If the truck is off and I start it in reverse it works just fine.
View 3 RepliesFord - Taurus :: Clutch Stay Engaged When AC Is Switched On Even In Cooler Weather?
I bought a 2005 Ford Taurus last month with a bad A/C clutch. I had a friend, who says he knows about such things, replace just the clutch. He says he lost no refrigerant, which should be right. The A/C blows cold OK regardless of the ambient temperature, but the new clutch clicks in and out. I was of the opinion that this was caused by a low charge.
My (not always right) friend thinks it's normal, due to the cooler weather. I THINK the compressor should run all the time, and the car's interior temp is regulated by the flapper doors. I have no way to capture the present charge and weigh in the exact amount needed. I have accurately weighed in an additional 8 ozs, with a good digital scale, and it still clicks in and out. I have readings of 125/25, but the outside temp is only 50F this morning.
What readings should I see at 50F? Do I still need more R134a?
Ford :: Buzzing / Rattling Noise When Clutch Engaged To Shift To 3rd Gear
My manual 2004 Ford Ranger XLT (4.0L) has been Buzzing/Rattling. (VIDEO LINK BELOW) She has 112k miles on her. Owned 1 month, no issues when I bought from my paps. Its my 1st manual so may have been a little hard on clutch 1st few days. Noise started abruptly 1 week ago when I engaged clutch to shift to 3rd. Its gotten worse over the few days and happens even when in gear. Its much more prominent from outside passenger window. Don't notice for 1st couple mins of driving & is intermittent but often. Noticeably louder when foot is taken off gas in motion. Does not make noise when idling. Generally only above 1500 RPM . Not coming from the back half so I don't think its the exhaust/heatshield
Heres the sound......
Ford 6.0L Power Stroke Diesel :: Fan Clutch Stuck In Engaged Position
06 6.0 fan clutch stuck in engaged position. So I changed the fan clutch it doesn't stay engaged anymore. comes on during startup and gives the appearance that the batteries are dying. Stays on for about 10 minutes when first driving then goes off. If I run ac it comes on at every light and it doesn't matter what engine coolant temp or oil temp and they are all within 6 degrees of each other. I'm thinking maybe the AC is a issue or bad sensor somewhere. No codes everything seems to be functioning. When I say comes on it's on high speed roaring.
View 14 RepliesFord F-150 - 1997-2003 :: 4x4 Light On Lower Right Of Dash Pops On When Clutch Pedal Is Engaged
I have a 1997 F150 XLT 4.6, standard transmission. the problem is every time I push the clutch the 4x4 light on the lower right of the dash pops on the power windows and windshield wipers will not work, releasing the clutch everything and goes back to normal, I checked the relay that was clicking every time I push the clutch in and switched it out same problem. As of yesterday the problem has now reversed, when the clutch is released everything doesn't work and a 4x4 light pops on.
View 6 RepliesAccent LC (2000-05) :: Clutch Grabbing When Engaged
I bought a used accent 1.3 before few months , with 100k miles on the clock. I did all the basic maintenance stuff, oils, filters, spark plugs, coolant, timing belt etc... I replaced the clutch disc also, because it was slipping.
The problem is that the clutch engage with a knock sound, just like when you have a loose engine mount. But... if i stay with clutch pedal pressed for a second, do the shift and released, the clutch engage smooth and all works fine. So, that's the way I do shifts for now.. Is this a flyweel problem?
Golf IV / Jetta IV :: 2003 GLI - Air Compressor Clutch Will Not Getting Engaged
I have a 2003 2.8 GLI and my compressor clutch will not engaged i provided the clutch with a direct power and ground from the battery and it engaged. i also went to the junk yard and got a couple of Fan Control Module ($4 each) and it still does not engaged.
View 3 RepliesPassat (B5) :: Clutch Engaged And RPMs Shoot Up Fast
Last week I took my baby to AWE Tuning, and had a chip and a diverter valve installed, when i left it felt like a different car it was great! now when im driving its not right, ok ill be in gear and as soon as i get on it and hit like 3thousand rpm it feels like the clutch is engaged and the rpms shoot up fast and the car isnt moving like it should. is it my clutch?
View 1 RepliesElantra XD (2001-06) :: GLS Clutch Engaged And In Gear But Car Will Not Move
Here's the scoop: 2 year old clutch & flywheel with 21,000 miles on them. Clutch master cyl. is full & not leaking. The clutch slave cyl. moves when the clutch is pressed & is also not leaking. The shifter linkage has been checked at the shifter and moves freely as it should.
I started the car, put it in gear, let the clutch out and there is no movement from the car regardless of the engine revs. The engine runs freely and does not die with the clutch engaged and the transaxle in gear. Putting it in ANY gear (including reverse) has no effect. The car will not move.
After turning the engine off I left the car in gear, left the e-brake disengaged, released the foot brake and the car stayed put. I then put the shifter into neutral, let the foot brake off and the car began to roll. I stopped, put the shifter back into 1st, let the foot brake off and the car was again stationary and did not roll. This tells me that the shifter linkage indeed works and that the car WILL go into gear. So, why won't the car move under power?
Golf/GTI VI :: Engine Noises Coming When Idling With The Clutch Engaged
I've been noticing my GTI has been making some weird noises, especially after only have 380 miles on it. When idling with the clutch engaged, it makes a rattling noise that goes away when depressed. There's also a rather loud sound coming from the timing belt and just underneath the plastic engine cover. I'm hoping it just needs breaking in, but I'd just like some reassurance that it's nothing serious.
View 8 RepliesGolf IV / Jetta IV :: Clutch Not Stay Engaged After New AC Compressor Installed
99 Jetta, installed a new AC compressor a month ago, has been working great, not clutch will engage for a few moments, then turn off for a minute, then engage again. Seems, like there is Freon in there by the gauge on the low side.
View 4 RepliesGolf IV R32 :: Grinding At A Full Stop With Clutch Fully Engaged
Within the past 2 weeks I've been noticing that when I shift hard into 2nd and 3rd, I manage to grind the gears slightly. At first I thought that maybe I wasn't engaging the clutch fully but after enduring rush hour traffic in the hilly streets of SF yesterday, I noticed that I could replicate the grinding at a full stop with the clutch fully engaged which makes me think that maybe my clutch is going bad.
I'm a bit unsure since the car still pulls up the hills like a champ (maybe it could be pulling harder?) and need to point out tell tale signs to look for when your clutch is starting to fail and requires replacement.
If my problem is not due to clutch, what could it be? If it is, any good place in bay area to take the R? I plan to replace with stock set up.
Currently I have stock clutch w/ +73k miles. I did have an episode where a car transporter managed to make thick grey smoke pour from my clutch due to ineptitude so clutch failure would not surprise me.
Elantra XD (2001-06) :: 2002 - Clutch Stays Stuck Engaged
My 02 elantra gls 5 speed clutch has gotten stuck engaged for about the third time now. First time was right after I bought the car i noticed the clutch would slip randomly for no reason. At first i thought the clutch must need replaced, but then other times I couldn't make it slip if i tried by going up steep hills with car full of people and shifting too soon on purpose and punching gas....no slip. So anyways i replaced the slave cylinder, and all was good till one day my wife calls me up stranded and says clutch pedal is rock hard and none of the gears will engage. so i tow the car home and fiddle around and realized the slave cylinder (brand new one) was stuck out. I opened the bleeder and it returned without me having to push on it or anything. i then bled the system thoroughly. So months have gone by and the slave cylinder got stuck out again, and again it was a simple turn of the bleeder valve and it went back and works fine. just curious as to how i can fix this problem permanently since its irritating and seems to be reoccurring. do i need to replace the master cylinder as well or did i buy a bad slave cylinder?
View 6 Replies