Accent MC (2006-11) :: CEL Flashing / Rough Idle - Cylinder 1 Misfire
I did not get the specific cel code but its what the guy told me at autozone.
Long story short. Washed engine, let sit for about 30 mins. Car started with flashing CEL and was "puttering" and very rough idle. Drove home took intake off and replace with stock, took spark plugs out and they were not wet. Then let it sit for about 15 mins. Started just fine. No CEL at all.
The accent saved the CEL and the guy told me that Cylinder 1 had a misfire.
My question is, should I do anything now even though the car seems to be running ok?
Kia - Optima :: 2001 - 4 Cylinder Rough Idle And Dies Out?
This car has had trouble since the get-go and am considering never buying another Kia again, but since its my only car as of right now, I need it to be running clean and good, which is not the case at the moment.
I have had another big problem with my Kia for almost a week now. Every time I crank her up, it starts fine, but then it has a horrible time idling and staying idle. After ten seconds or so, it dies out and emits a big hiss (sounds like someone is sighing, but worse).
So had a trusted friend mechanic come over and look at it. At first, he thought it could have been a clogged Cat Converter, since I have known for a while that it's bad and just don't want to spend a grand on the car since it's not even worth that much anymore. He tried running a diagnostics to see what codes were popping up, but for some reason the car doesn't want to give a code.
So my friend did an overall inspection of the car and recommended that maybe a spark plug/wire change could do the trick. It didn't. We changed it but still had the same problem.
Then he went to the trunk of my car and tested the fuel pump, which then he had a glimmer of hope since he said there was barely any pressure going to the fuel pump. So we got a new fuel pump. Can you guess what happened next? Yep, the car still had the same problem.
Then he went back to the hood and looked it over. He didn't like what he saw on the CAM sensor, so he did a test on that, too. First he ran the car with it in, and it rough idled and then died. But, interestingly enough, he took it out and the car ran a lot smoother, albeit only a couple of seconds, before it finally decided to quit. But it did run smooth, so our hope was back.
So we went back to Advanced and got a new CAM sensor. Tried it on the engine. Our hope was crushed. Same problem, rough idle, then it chokes out. Then he looked at the wires and noticed they looked pretty bad, and the next time I started it up for him, he said they "exploded".
He got on his mechanic website to look up the wiring diagrams for the car to try and find the ECU, but he didn't want to take the car apart to get to it, and it was dark, so we called it a day.
I'm going to try and get AAA to tow it to his Honda Dealership tomorrow so he can get some second opinions on it and have more tools to work with to try and get this beast running. But hopefully it could just be that faulty wiring?
Accent LC (2000-05) :: Misfire On Cylinder 4 After Warming Up Only In Idle
2004 Hyundai Accent has is misfiring, after warming up, only in idle. This only happens after about 30 seconds in idle. Could it not be getting enough gas? This being said I was getting misfire on 3 as well but that would happen all the time and cause the entire car to shake. This problem is now fixed and only #4 is causing me problems.
View 2 RepliesElantra XD (2001-06) :: Cylinder 2 Misfire / Rough Idle Especially After Fill Ups
I have a 2001 Elantra with 170K miles. well taken care of. I've been having a rough idle issue for some time now. The car idles very rough. I checked for codes and I got the cylinder 2 misfire code (P0302)...
I started out and replaced the plugs and wires, no solution...
I replaced the coil packs, no solution...
I replaced the MAP sensor, no solution...
I figured it may be no to low compression, so I did a compression test and all cylinders came back normal, still no solution...
I figured it might be a dirty injector, so I poured some seafoam in the gas tank, and no solution...
So my next step is to switch out the injector. Is there anything I am overlooking?
Here's the big thing that is happening too... Everytime I fill up the gas tank, I turn the car on and it idles even rougher. Like if you talk while sitting in the car, you sound like Chevy Chase when he is on the vibrating bed with Beverly D'Angelo in the movie vacation! LOL. It slowly goes away after 10-15 minutes of driving. All this rough running engine ONLY happens at idle, otherwise it runs very smoothly.
Ford Excursion :: 2000 V10 - Rough Idle - P0304 Code / Cylinder 4 Misfire
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesFord Ranger / B-Series :: 2001 - Rough At Idle / Misfire In Cylinder 1
So I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
Accent LC (2000-05) :: Difficult Start / Rough Idle And Misfire
Symptoms:
- Check engine light: misfire on all cylinders, and "lean fuel trim at part throttle".
Started with changing leads and plugs without improvement. Then I found the tank ventilation seemed to be clogged, as there was a massive vacuum when opening the filler cap. Checked the canister and replaced a couple of corroded lines. Also used compressed air to blow through the canister and lines up to the Evap-purge valve. Seemed to be OK afterwards (no vacuum), but still misfires.
Changed the Mass Air flow sensor, and it seems the misfires got better, but instead I have some other issues:
- Hard to start when cold. Starts up fine for a second then sounds like it's getting to much fuel and dies. Possible to keep it running if pumping the pedal or holding it at higher revs.
- Rough idle when warm. (Same as before I changed the MAF and plugs/ leads.)
- Drives and runs ok when out on the road.
- Pulled the cable to the Idle Control Valve without any change in idle...?
- Got flashing engine light and "misfire cylinder 4" when giving full throttle on low revs and seond gear up a steep climb.
What could cause this?
- Temperature sensor?
- O2-sensor?
- Idle control valve?
- Coilpack?
Accent MC (2006-11) :: 2009 - Idling Rough / Cylinder 2 To 4 Misfire
So recently my 2009 hyundai accent has been idling rough, and has been very sluggish when accelerating. Usually the rough idling is the worst when the car is first turned on and tends to tone down as the car keeps running. I had the codes red and I believe it was C0302 C0303 C0304, saying that cylinders 2-4 were misfiring.
I replaced the spark plugs which didn't fix the problem, although cylinder 4 did have a small amount of oil above the spark plug and a little bit more below the spark plug, I am not sure if that means anything useful or not. I don't have a way to check the coils directly but I swapped coil 2 with coil 1 and checked the codes again and it was still cylinders 2-4 misfiring, so I would imagine that means the coil isn't the problem. I then tried spraying WD-40 around the vacuum tubes, and if the intake manifold is on the back of the engine I tried spraying it around that gasket as well, but I didn't notice a change in the idle speed.
At this point I am not entirely sure how to proceed, from what I have read the issue causing a misfire would be either there isn't a spark, which seems unlikely at this point, or the mixture of fuel to air is wrong. That is the part I am unsure of how to diagnose/
Passat (B5) :: 1.8T - Rough Idle / CEL Came On / Misfire On Cylinder 4 And 2
So every once in a while I would start my car and get a rough idle but not too bad. I got a cel after a few times of this happening. I had a misfire on 1 and 4 and possible misfire on 2. It was ok for a a couple days. But during the last few days I'll start it up and it's fine. But then if I shut it off and restart it will have a rough idle again. Also today I got gas and then it rough idled and when I would shift or put it in neutral the rpm would stay up and drop slowly down. Like if I shifted gears I could almost do it without the rpms dropping at all. I've got 110k. ??
View 6 RepliesAccent LC (2000-05) :: Cylinder 4 Misfire When Refueled
I have a 2004 Accent Gt with only 43k miles on it and I am getting a cylinder 4 misfire when I refuel. I have replaced the 4 spark plugs. The original code was random multiple and now it is just cylinder 4. I tried to swap 2 spark plugs to see if maybe there was something wrong with the plug but the misfire did not move to another cylinder. I've read about maybe swapping fuel injectors, where I can find directions on how to do that?
View 8 RepliesAccent LC (2000-05) :: 2002 1.5L - Misfire On Cylinder 3
I have an 02 Accent 1.5L that has a misfire on #3. I have replaced the head gasket, valve cover and gasket, intake gasket, timing belt, yes it was top dead center, MAF, Charcoal canister sensor, MAF, plugs, wires, coil pack, injector #3, and the compression in #3 is 130. What else to check. No other codes.
View 3 RepliesAccent LC (2000-05) :: 2002 1.6L - Multiple Cylinder Misfire
Car threw a multiple cylinder misfire, changed plugs, wires, and then coil packs. Code keeps coming back.
View 12 RepliesPrius (2004-09) :: Misfire On Cylinder 2 And 4 - Car Severely Idle Rough
I own a 2007 prius, it has about 320,000 miles. It has recently been diagnosed with a #2 and #4 cylinder misfire. The car severely idles rough, but when getting in the gas it goes away. I have replaced the spark plugs, the old plugs were very white(lean), replaced fuel injectors, used fuel injector cleaner. I've sprayed carb cleaner around the intake to see if I might a leak--no leak. The motor uses about a quart of oil every 1,000 miles since about 100,000 miles. I'm just guessing, could it simply be low compression causing this? I pulled the new spark plugs after about 5,000 miles and they where white also.
View 9 RepliesLexus GS 2006-11 :: GS300 Rough Idle / Misfire On Cylinder 2
I bought a 2005 3rd gen about 8 weeks ago and I love it except for one problem, a really bad idle/vibration through the cabin when cold starting, it improves when the engine is warm but is still noticeable.
It went back to the dealer where I got it and they gave it a full service, new plugs, oils and filters and replaced the transmission oil too after the check vsc and engine management lights came on.
The codes pulled showed a misfire on cylinder 2, the dealer said the service would cure all and sure enough no more vsc lights but the rough idle and vibration are persistent.
The car has only 78000 miles and I'm pretty certain a Lexus isn't supposed to behave like this.
Ford F-150 (2004-2008) :: Rough Idle Cylinder 3 Misfire
2004 Ford F150 5.4 Triton 3V Vin5.....
How this started, Drove through a lot of water as our City was in a flood on my way home and and the truck started running rough and got worse over time, I can now barely get to 40 mph as it starts to ping and sputter with no power.. the truck has been parked and not driven while in the shape it's in.
The truck keeps giving me error code P0303 Cylinder 3 misfire detected, P0174 System too lean (Bank 2) and at times another error P0300 saying multiple cylinder misfires detected.
After clearing the codes, I got new codes stating Misfire on Cylinder 2, 3, 4, 6. System too rich (Bank 1) System too lean (Bank 2)
Cleared the codes again and I'm back to Cylinder 3 misfire and System too lean (Bank 2)
What I have done so far... All repairs with in a few days...
1. Changed all spark plugs.
2. Changed all Coil Packs.
3. Changed number 3 fuel Injector.
4. Changed the Oil and Filter. (no water in the oil)
5. Changed the MAP Sensor.
6. Changed Bank 2 O2 Sensor 1 and 2.
7. Loosen the Catalytic Converter on the drivers side to re-leave back pressure thinking the Cat was plugged, still loss of power. I also drilled a small hole in the exhaust at my lowest point to see if it had water in it and it does not.
Checked for vacuum leaks using starting fluid around the intake manifold, no change in idle.. I also checked to make sure the vacuum line was still connected on the back of the intake manifold, I have found nothing leaking.
I also had cleaned the throttle body and changed the throttle position sensor.
Repairs within the last 6 months or less...
8. Replace passenger side cat.
9. Replaced both Bank 1 OS Sensors
9. Replaced Timing chains, Gears, Guides, Guide Tensioners, Oil Pump and pickup tube, Water Pump.
Cam Phasers are fine.
And number 3 coil is getting spark I changed the Ignition Coil again thinking maybe another bad pack.
Still #3 misfire and System too lean (Bank 2).
I am at a loss and not sure what to try, except for a compression test on cylinder 3 but I honestly don't think it's compression or a burnt valve.
Accent LC (2000-05) :: CEL Flashing / PO301 Code - Misfire In Cylinder 1
I got a 2002 and its giving ma a po301. I know that means a misfire in cylinder 1. I replaced the Coils, Plugs and wires, and now its still there but the check engine light is flashing. What next?????
View 2 RepliesChevrolet - S-10 :: 1996 - Running A Bit Rough / Irregular Idle / Cylinder 1 Misfire
My 1996 S10 2.2 liter pickup has been having some 'issues'. Truck has been kind to me over the years, but now is running a bit rough. It has an irreguler idle and continues to run this way through all speeds. The blinking code reads "cylinder 1 misfire". I did all the basics. I changed the plugs and wires, ignition coils and fuel filter. Here is where is gets tricky, after changing the fuel filter, it ran great again. Then it started to run rough again later that day. I thought I somehow clogged up the new filter, so I removed the new one for inspection. Realizing there was nothing wrong with it, I reinstalled. Truck ran great again. Went out to drive it to work a couple hours later and it started fine, then after about 10 seconds of running, it went back to the rough idle.
View 19 RepliesFord Ranger / B-Series :: 2002 XLT - Rough Idle - Misfire On Cylinder 3
I have a 2002 ford ranger xlt 3.0 i just rebuilt the entire motor about a month ago and was having a high idle problem for the longest time. turns out i had the iac on backwards. but now that it idles down around where its supposed to it has a rough idle has a little shake to it. starts up right away but when i drive down the road around 3000-3500 rpms its missing on cylinder #3 from what the code I am getting "multiple cylinder misfire, #3 cylinder misfire" I've replaced plugs and wires. camshaft pos sensor. I am getting 65 lbs of fuel pressure. spark on all cylinders. I am really at a dead end here. Also every time I take the plugs out to look at them they look brand new.
View 14 RepliesAccent LC (2000-05) :: CEL Came On / Cylinder 4 Misfire - Exhaust Started Sounding Loud
I just bought a 03 accent the same day i bought it the CEL came on got it read and it was cylinder 4 misfire. took it to the garage the dealer i bought it from takes it to he said there was a little water around the boot in that weird little channel area under the cover he said he cleaned it up dried all out then reset the code and it was good, for a little about 2 weeks later it comes on again i get it read and it says cy 4 misfire again but also P0133 (o2 sensor bank 1 sensor 1) and i cannot remember exactly but i think the CEL came on after the exhaust started sounding loud, like it has one of those ricer mufflers on it.
Well I jacked up the car today and looked the only thing i saw was after the first cat right before the braided flex pipe there is this weird "shield" looking piece on the underside of the exhaust pipe dunno if its really supposed to be there or what it is for but from somewhere under that piece i can see exhaust coming out(its cold right now) also the flex piece is kinda blackened like its had exhaust fumes blowing on it for a while. i cant imagine why this would be a normal thing but i have never worked on hyunda before. i am thinking if there is some sort of "leak" there that is why the o2 code is showing. i am stumped, esp on the cy 4 misfire all sparks and wires look good i pulled each wire with it running and it bogs down til i plug it back in.