Accent LC (2000-05) :: Camshaft Position Sensor - Circuit Low Input
My 1.5L 2000 Hyundai accent is reading p0342 code.(cmp sensor circuit low Input). I have changed out the sensor from a parts car and it's still reading this code. I've read it could be timing or an issue with the starter wiring.
View 3 RepliesAccent MC (2006-11) :: Code P0707 - Transmission Range Sensor Circuit Low Input
The MIL light came on and I noticed the shifting P-D or P-R was hard. Checked the Transmission Fluid and noticed it was low. Topped it up, but still MIL is on and shifting hard still. I bought a OBD2 Scanner and it returns P0707 "Transmission Range Sensor Circuit Low Input". Should I try clearing the DTC? It's a drag because it's my wife's car and she's driving mine.
View 1 RepliesAccent LC (2000-05) :: 2002 - Code P0106 / Map Sensor Code
Ok had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
Accent LC (2000-05) :: P0501 Speed Sensor Code Lit Up
The MIL light up and I got the P0501 Code. (Speed Sensor. I use a Scangauge II and the Speed is 0 KM/H at any speed. (was working before). But the in dash Speedometer work no problem. I look on the HMAservice web page and did not found where is located the Speed Sensor.
View 9 RepliesAccent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesAccent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesAccent LC (2000-05) :: Code P0335 / Replaced Crank Sensor / Still No Spark
Like the title says...'02 Accent,1.6 dohc.Won't start.No spark.
Pulled code p0335-crank sensor circuit A.
Replaced sensor...still nothing.
Is there something else that commonly goes with these symptoms?...or did I just get a bum sensor?
Also,once I try starting or turn key on,I hear a buzzing coming from throttle body area for about 10 seconds even after key is off. Not sure if its related or normal.
Accent LC (2000-05) :: Transmission Temperature Sensor Location / P0711 Code
Wife's car threw a p0711 code. It says temp sensor failure or whatever. I found the part on rockauto for 22 bucks but that's not the issue. I've tried searching about this and I seem to find some stuff about elantras and sonatas. I can't seem to find anything specific to a accent. I've read that it's inside the transmission which is fine I've changed valves before and such on old rwd transmissions. But some things I find say it's on the bottom and some say the side. Also wiring is mentioned pretty often with service bulletins.
View 28 RepliesSanta FE SM (2001-06) :: CEL On / Code P0107 - MAP Sensor Circuit Low Input
My check engine light is on. I got the code pulled at Advance Auto Parts. It is P0107 - MAP Sensor Circuit Low Input. I wanted to test the MAP sensor to see if it is bad. I couldn't find anything online that was Santa Fe or even Hyundai specific as far as testing procedures go. I know you can test the power wire, the ground wire, and the signal wire, from what I could tell from other places I've looked. I got 5ish volts from the power wire and 12ish volts on the ground wire, which is what I understand they should be. I don't have a vacuum pump at the moment, but testing the signal wire with no vacuum I got about 0.02 volts. From what I've read online, it should be around 5 volts, but I wasn't sure if all MAP sensors work the same way. Whether I'm doing this correctly and whether they think the sensor is bad?
View 5 RepliesAccent LC (2000-05) :: Code For Output Shaft Speed Sensor - Transmission Rebuild
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 RepliesAccent LC (2000-05) :: Code P0326 - Can A Knock Sensor Be Influenced By Heavy Bass?
I have upgraded my sound system in my car and sometimes i get a P0326 check engine light.
Now i was wondering if its possible that the Heavy bass ( 25/40 Hz, 1200 Watt RMS and 2500 watt Max) Subwoofers could cause the car to vibrate so much that it sets of the knock sensor?
I have read some things about it but i only found that several "Old" cars with OBDII would have this problem? Is that the same on this hyundai accent?
It only comes once in a while after long cruises and bumping.
Santa FE SM (2001-06) :: Code P0715 - Input Speed Sensor Location?
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 RepliesElantra XD (2001-06) :: 2003 - CEL Code P0113 / IAT Sensor High Input
So my mom recently bought a 2003 Elantra (75K miles, auto trans) and within a few days the CEL came on. She took it in to PepBoys and had them hook it to their scanner to get the codes out of it. The only code that came up was P0113 Intake Air Temp (IAT) Sensor high input. I've done a little research on the net but there is a lot of random info for this code out there. Is the IAT a separate sensor or is it combined in with the Mass Air Flow (MAF) sensor(if this car even has a MAF) or combined in with the MAP sensor? I've read on the net that it could be any of these 3, I think it's combined into the MAP.
I've also read that this code could be caused by a bad IAT, bad O2 sensor, an exhaust leak, bad wiring/ground(I checked the wiring/grounds visually and everything seems ok) or many other things. If it's as simple as replacing one of the sensors I can do that myself, I just don't want to go randomly buying things and either it be the wrong part or have it be the right part but not fix the problem. The car runs great, even with the CEL on. Yesterday when she stopped by my house I disconnected the battery for a couple minutes and reconnected it, started the car & no CEL. She drove the car for about 125-150 miles before the light came back on.
Ford - Windstar :: Code P0113 - Intake Air Temperature Sensor 1 Circuit High Input
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 RepliesFord - Explorer :: 2004 V6 - Code P0715 - Input / Turbine Speed Sensor Circuit
2004 Sport Trac V6. Been having hard shifting and P0715: Input/Turbine Speed Sensor Circuit. Cleared the codes and still returns.
From my searches, readings and looking at the parts diagram. On the newer 5 speeds the sensor is the one on the inside of the tranny. This requires taking the entire tranny apart? Is there an external connector for the sensor that I can check or clean first? Replace this sensor. I know the older ones were mounted on top of the tranny. I think this one is mounted on the inside though.
Passat (B5) :: Check Engine Light On / Code 16486 - Mass Air Flow Sensor Circuit Low Input
I cleaned my k&n air filter on my 02 passat 1.8 turbo let it dry oiled it very lightly, and 50 miles later I get a check engine light on, pulled the code 16486 and it says Mass or Volume Air Flow Circ Low Input. Cleared the code put a frame in until I can get it filter. Why that would throw me that code, k&n oil gumming up my sensor??
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 VSS E350 Short Bus - Changed Sensor But No Input AE?
I have a 2000 Ford E350 Short Bus 7.3 It has abs in the rear diff. I have changed the sensor. I have connected my AE but get nothing at all from the sensor. My speedometer does work. My overdrive light flashes and the transmission does shift properly. I plan on looking for a bad ground. Can I test the wiring using a volt meter
View 2 RepliesAccent LC (2000-05) :: Knocking Sensor Location?
Where the knocking sensor is located on a 2005 Accent. I am in need of finding it so that i can wire a controller into the signal wire?
View 2 RepliesAccent LC (2000-05) :: Speed Sensor Location?
trying to find the speed sensor on a 03 accent manual so I can fit cruise control
View 1 Replies