Ford F-150 - 1997-2003 :: Running Too Lean On Both Banks
My F150 5.4 V8 is running to lean on both banks according to my code reader. I have replaced the fuel filter cleaned up the air filter and I am about to put in seafoam in the gas tank to clean out the jets and carb. I thought fuel pump but have never had to deal with this before. I just bought the truck last thursday. Also my gas gauge is stuk at empty and the low fuel light is on ....
View 14 RepliesFord F-150 - 1997-2003 :: Check Engine Light Just Came On / Lean On Banks 1 And 2
99 F250 LD 4x4 w/5.4 - 218k .... Check engine light just came on so I had the trouble codes pulled. 071 and 074 . Lean on banks 1 and 2 . Truck is running fine as far as I can tell. I know it can be o2 sensors, pcv, maf sensor or loose vacuum line somewhere. I just put a new motorcraft pcv valve on before this happened so I rechecked the lines , all seem to be fine. Is there a inexpensive scanner that I can check the o2 sensors without just throwing money at new ones.
View 3 RepliesFord - Ranger :: 1998 - Fuel Running Lean?
1998 ford ranger 4.0 ... fuel running lean ... how do you adjust it??
View 3 RepliesFord Ranger / B-Series :: 1990 - Rough Start - Running Lean?
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new
Ford Ranger / B-Series :: Truck Sputters - Cylinders 2 / 3 And 4 Misfiring - Bank 1 And 2 Running Lean
I have a 99 ford ranger xlt 4.0 ohv basically it sputters so bad while driving it sounds like a dump truck but it all started when I changed my o2 sensors but in doing so I broke my heater control valve and when I was going down the road it started sputtering well it started sputtering so I checked the o2 sensors there good and I changed the heater control valve. But nothing so I changed my coil pack spark plugs and wires but still nothing. But on my reader it says cylinders 2,3, and 4 are misfiring and bank 1 and 2 are running lean plus it has a bad aroma of gas in the engine compartment but when it idles its somewhat smooth but when I'm driving it its horrible the sputtering is so bad it takes awhile to get up to speed plus I'm only getting 100 miles to a whole tank that's like 8 or 9 mpg I need to fix this soon. This is my only transportation...
View 11 RepliesFord Ranger / B-Series :: 2000 - Running Rough And Code For Misfire On Cylinder 3 / 2nd Coil Pack
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesFord - F150 :: 1999 - Code P1131 / O2 Sensor Running Lean
I have a 1999 Ford f150 4.6L automatic. My check engine light had been on for awhile so I dug out my DTC code reader erased it, came back on 10-15 minutes later. I got the code P1131 sensor indicates lean which you would think is the O2 sensor a week later it won't start. Then randomly a couple days later it starts then that night it didn't. Hear is the parts that confused me. I don't believe an oxygen sensor would cause it not to start, it's cranking nice just won't turn over. And when you get the code P1131 I believe it bay 1 where the readings are off Well here's my readings.
Fuel system 1 CL-FaultCalc load 34.1%ECT 201.2 FSTFT B1 -1.6%LTFT B1 0.0 %STFT B2 -1.6%LEFT B2 0.0%ENG RPM 1101VEH SPEED 27 MPH
It looks like to me bay 1 and 2 are off? I'm not mechanically challenged, but not a mechanic either, I do most my own work on my vehicles..
Ford Ranger / B-Series :: 2000 - Check Engine Light On For Lean Condition - Getting 10 Mpg?
My 2000 ranger with the 3.0 is only getting around 10 or 11 mpg. It's got a check engine light on but the scanner just says lean condition. The truck also has a rough idle. I've replaced the fuel pressure regulator and fuel filter.
View 14 RepliesTiguan :: CEL Code P2187 / Running Lean At Idle
Driving home yesterday and a check engine light came on while I was at a stoplight. When I got home I plugged my scanner in and came up with a P2187 code, running lean at idle. Cleared the code and went inside to start doing my google homework.
Looking around various threads I'm leaning towards the PCV valve being shot. Seems like they go quite a bit and it describes quite a few of my problems going on; CEL, lumpy idle, and a bit sluggish.
Currently at 50k miles on my 2011. I've been Revo stage one for about 7k if that makes a difference too.
GTI 337/20th Anniversary :: CEL On - Code Is Running Lean With A Base One
I was parking today and when i looked up my CEL was on. So I got the code pulled and it turns out I'm running lean with a base one. I think it was? the mechanic told me it was my o2 sensor but I'm not sure which one it may be whether it be before or after the cat?
View 5 RepliesFord Fuel System :: 2003 F150 - Service Light Randomly Comes On / Code For Left Bank Running Lean
2003 f150 supercrew with 166,000 miles on it. Daily driver. Service light randomly comes on and when code reader was put to it shows "left bank running lean." Will clear it and will randomly come back on. Truck seems to be running fine. No issues engine. Bad sensor? Or bad injector? Maybe way to test?
View 1 RepliesFord F-150 - 1997-2003 :: 2000 - Code P1151 Lean On Driver Side - Truck Bog Down At About 50 - 60 Mph
I have a 2000 f150 with a 5.4 past few months it has been throwing a p1151 code meaning it is coming up lean on the driver side. I just changed the plugs and it didn't work, neither did changing the fuel and air filters. cant find any vacuum or exhaust leaks. Replaced a bad injector along with the spark plugs and its still coming up lean.
The truck also seems to bog down at about 50-60 mph if i let off the gas and coast it will drop about 300 rpms. It has me confused and annoyed, i have true duals with glass packs could that be causing it?
Elantra XD (2001-06) :: P0171 Generic Engine Running Too Lean Code Popping Up
I picked up a really cheap Hyundai Elantra 2005 that the kid that owned it really beat up on. Right now I am trying to sort out the issues so that it can become my daily driver for the next few years.
Second issue, The check engine light is on and it is popping up a P0171 generic engine running too lean code. The car looses power sometimes and I can smell gas in the car. I have a friend that is going to be loaning me his MAC code reader so that I can see if it is one of the O2 sensors and if so which one tomorrow.
Accent LC (2000-05) :: Code P2096 Post Fuel Trim Too Lean
Car Throwing This Code ... P2096 Post Fuel Trim Too Lean-B1 ...
View 8 RepliesAccent LC (2000-05) :: Code P1128 - Long Term Fuel Trim Too Lean
I found on internet loads of comment about this error code, but in my case the only bad thing is with fuel consumption - about 9-10 litres (!) for 100 km on motorway. Normaly it should be about 6-8 litres.
The error means: "P1128 is "Long Term Fuel Trim Too Lean". Which means the air/fuel mixture is leaner than the HO2S can compensate for."
Idle is working correctly (i think thats to do with MAF), engine start without any problems and overall car running smooth.
What can cause a bad fuel consumption? Is anything to do with a lambda (O2) sensor or it could be something else?
Lexus - RX300 :: 2000 - Check Engine Light Code P0171 Bank 1 Too Lean
2000... I have a code P0171 bank 1 too lean. My question is does this exclude anything that will effect both banks? If it was MAF sensor or fuel filter would it set code and say banks 1 and 2 running too lean? In which MAF sensor ohms out correctly. I cannot view fuel trim files. I have looked for a vacuum leak with no luck. I got some cigars to try to smoke it to see if there is any vacuum leaks. Trying to narrowing what i need to checks.
View 19 RepliesAccent LC (2000-05) :: Check Engine Light Error Code P1128 / Too Lean Intake System
This is the infamous error code many Accent owners might have experienced it. The code refers to "Too lean intake system". People try to replace all kinds of parts like ECM, MAF, O2 Sensor, TPS, Fuel Pump, Fuel Filter, etc. according to my research. I just bought a 2001 Accent and the P2188 light came on. I wrote an email to Hyundai Corp. Asking what would be the most likely part that will cause the (P2188) check engine light to come on.
View 3 RepliesFord Ranger / B-Series :: 1998 - Running Rough And Now Getting P1151 Code
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 RepliesFord Ranger / B-Series :: 2000 3.0L Running Rough / Shuddering At Stops
I have a recently purchased 2000 ford ranger 4X4 with approx. 130,000 miles on a 3.0L. When I bought the truck, it was running rough while in gear at idle, after first putting it in gear, and when coming to stops, then it quit running all together. I started by replacing plugs, wires, and ignition module. I finally got it to fire up after that, but instantly noticed the tell tale white smoke from the exhaust. Needless to say, my oil looked like chocolate milk. Rather than having the heads machined and checked, I opted to purchase a new set of cylinder heads from Dover cylinder head.
I got those on this week and she fired right up. After a few oil changes to eliminate the residual coolant from the oil passages, she still starts and runs fine, although the idle is a bit rough while in park. When I place it in gear the idle gets a little rougher. After a quick trip down the road, I'm noticing a pretty solid shudder when coming to a stop, almost like it's stuck in 2nd gear, but I can't really tell for sure. Seems to shift fine going up through the gears, but coming down is when the issue is.
I believe I'm dealing with two separate issues, one being the rough idle upon startup that doesn't seem to go away, and two being the rougher idle upon stopping. I've read everything from EGR valve, idle air control valve, low fuel pressure, and a laundry list of other things, and I just don't want to start throwing money away chasing my tail.