Passat (B5) :: Check Engine Light Came On - Code P0171 / Fuel System For Bank 1 Was Too Lean
We have a 2003 Passat 1.8t. Had the Check engine Light come on. Went down to AutoZone and hookeded up the OBDII reader. Came up with P0171, Fuel System for Bank 1 was too lean. Probable causes:
1. Fuel Pressure of MAF (If Bank 1 & Bank 2 set codes together)
2. O2 Sensor
3. Ignition Misfire
4. Fuel Injector Problem
Car has 60K - has always run well. Wife says she thinks it's running a bit sluggish. I rarely drive the car, but I think she's right. Car is not missing or running rough.
I cleared the code & started the engine; Check Engine Light is off; then looked at the codes and I find a P0171 (Pending). She tells me that the light has been on before & then gone away. So I guess it clears itself, but eventually comes back.
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Came On / Code P0171 / System Too Lean Bank 1
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 RepliesFord - F150 :: 1998 - Check Engine Light On And Error Is Bank 2 / System Too Lean
My vehicle is a 98 F150 5.4 ltr Triton. I got a check engine light on and the error is "bank 2, system too lean." I read that this can be caused by a few different things like vacuum leaks or fuel filter and so far I haven't been able to narrow down. It started with occasional shaking at idle and its happening more as time goes. When at idle it often makes a sound like slurping the bottom of a drink with a straw and shakes intermittently. The fuel economy seems to have gone down. Sometimes it seems like it almost dies in idle, but always keeps running. It runs great when I push on the gas.
View 4 RepliesFord F-150 (2004-2008) :: Rough Idle And Dying / System Adaptive Fuel Too Lean Bank 1
2004 f150 fx4 w/ 5.4 .I have a code that read " system adaptive fuel to lean bank 1 " and the same for bank two. So, I got on here and did some research. Cleaned the throttle body, maf sensor, air filter, looked for vacuum leaks, changed the fuel filter and it still is running very poor at idle and it seems to be getting progressively worse...
View 2 RepliesTacoma :: P1071 Error Code - Bank 1 System Too Lean
I've searched for this and haven't come up with much other than the same error code for a bunch of other vehicles, and a bunch of different responses. My Tacoma is a 2000 PreRunner, 3.4 liter engine.
The exact code I get it is:
P1071
bank 1 system too lean
What this could be?
Ford F-150 - 1997-2003 :: Rough Idle - Right / Left Bank Too Lean?
I have a rough idle. I have replaced upstream o2 sensors, plugs, wires, fuel filter, dpfe sensor, cam sensor, and cam synchronizer. This has only moderately improved my problem. I still have the right bank, left bank too lean codes. Could it be something as simple but hard to find as a vacuum leak?
View 8 RepliesFord - Explorer :: 2003 V8 - CEL Came On - Too Lean Fuel Bank 1
Explorer 2003 - 116 mi V8... Has been idling poorly at about 750 / 800 rpm never stalls in idle.
Check Engine Light came on - Read code said Too Lean Fuel Bank 1
Reset codes. After a couple hundred miles Check Engine Light
Once again Check Engine Light
Same error code Too Lean Fuel Bank 1
Ford F-150 - 1997-2003 :: Bank 1 Too Lean Code
Well I got the ubiquitous "Bank 1 Too Lean" code this morning. Yesterday I changed out the PVC Valve, Elbow and Hose assy.
I changed out the hose from the intake to the canister purge valve on the firewall next to the master brake cylinder, that one was like dust.
Today I'm changing out the rear O2 sensors, but I may change out the fronts when they get them in (very rural area hear).
I'll keep looking for vacuum leaks and change out the MAF sensor. I hate to think it may be the intake....
Ford - F150 :: 1999 - Code P1131 / O2 Sensor Running Lean
I have a 1999 Ford f150 4.6L automatic. My check engine light had been on for awhile so I dug out my DTC code reader erased it, came back on 10-15 minutes later. I got the code P1131 sensor indicates lean which you would think is the O2 sensor a week later it won't start. Then randomly a couple days later it starts then that night it didn't. Hear is the parts that confused me. I don't believe an oxygen sensor would cause it not to start, it's cranking nice just won't turn over. And when you get the code P1131 I believe it bay 1 where the readings are off Well here's my readings.
Fuel system 1 CL-FaultCalc load 34.1%ECT 201.2 FSTFT B1 -1.6%LTFT B1 0.0 %STFT B2 -1.6%LEFT B2 0.0%ENG RPM 1101VEH SPEED 27 MPH
It looks like to me bay 1 and 2 are off? I'm not mechanically challenged, but not a mechanic either, I do most my own work on my vehicles..
Ford Excursion :: SES Light Came On About 15 Minutes Into Drive / Code P0174 - Bank 2 Lean
After installing Banks headers and full exhaust, I took my truck for another test drive this morning. SES light came on about 15 mins into drive and is telling me P0174 - Bank 2 Lean.
So that's the right/drivers side - my list of things to go check
O2 Sensor plug on that side
The MAF
The IAC
Vacuum lines ...
Nissan - Sentra :: P1273 - Air Fuel Ratio Sensor 1 Lean Shift Monitoring Bank 1 Code?
I got an 04 Nissan Sentra and I got a (P1273 Nissan - Air Fuel Ratio Sensor 1 Lean Shift Monitoring Bank 1) code that popped up on it. Looking to see what the probable cause for this code to pop up? Is this a rare code that popped up on this car? There's no noticeable symptoms going on with the car.
View 9 RepliesFord F-150 - 1997-2003 :: Bank 1 Or Bank 2 Too Lean Codes At Idle When Started Cold?
I've been having this problem since I've gotten the truck about year ago. it has very high long-term fuel trims and it seems no matter what I do I cannot get them to go down my fuel trims at idle are 39 Bank1 and 33 bank2 they go down to around 12>7 while driving what could this mean. And even weirder occasionally I get Bank 1 or bank 2 too lean codes at idle when cold starting???? 1997 Ford F150 4.6 ......
View 7 RepliesPassat (B5) :: 2001 - Code P0171 Too Lean Bank 1 - Emission Light Comes On
I recently had some work done on my 2001 VW Passat 1.8T (timing, water pump, major tune up). IT had 72K miles.....
Now I'm getting the following:
Code P0171 Too Lean (Bank 1).
Emission Light turns on / off.
Check engine light comes on and stays on after about 20 miles. Can this be the oxygen sensor?
Ford Fuel System :: 1987 F150 - Fuel Pump Keep Running Even When Key Is Off
I have an 87 F150 4x4 4.9L EFI with a single tank. Fuel pumps keep running even when the key is off. I tried swapping relays but the problem still exists. The engine will start and run OK for about 15 secs. then die. I installed a new low pressure pump, high pressure pump seems to be OK. I also installed new fuel filters. I dont want to just throw parts at this truck, where do I go from here?
View 4 RepliesLexus - RX300 :: 2000 - Check Engine Light Code P0171 Bank 1 Too Lean
2000... I have a code P0171 bank 1 too lean. My question is does this exclude anything that will effect both banks? If it was MAF sensor or fuel filter would it set code and say banks 1 and 2 running too lean? In which MAF sensor ohms out correctly. I cannot view fuel trim files. I have looked for a vacuum leak with no luck. I got some cigars to try to smoke it to see if there is any vacuum leaks. Trying to narrowing what i need to checks.
View 19 RepliesChevrolet - Trailblazer :: 2006 - Check Engine Light Code P0171 - Lean Bank 1
I have a 2006 Chevy Trailblazer LS/LT 4.2 liter 2wd. I have been trying to get it smoged, but can't clear the code. P0171 - Lean Bank 1.
I've been having a parts throwing contest with it, but it has been winning and my wallet is losing.
I have changed the air filter, cleaned the MAF sensor, changed both O2 sensors, changed the secondary air valve and relay. I've done the carb cleaner spray test around the intake and vacuum lines, with no spikes in RPM.
Most recent try was a couple bottles of Techron concentrate with premium chevron gas.(still waiting to see if the code hits again)
Next steps are checking the intake bolts(to see if they are torqued) and intake gaskets, check for exhaust leaks at the exhaust manifold, and checking the MAP sensor.
Freeze frame data from the most recent hit on the code is below.
***Fuel system 1 - CL***Fuel system 2 - NA***Calc Load(%) - 30.2***ECT(deg c) - 48***STFT B1(%) - 3.9***LTFT B1(%) - 22.7***MAP(kPa) - 33***Eng RPM - 809***Veh speed(km/h) - 0***Spark Adv (deg) - 10.5***IAT(deg c) - 20***MAF (G/s) - 5.82***TPS(%) - 15.3***Air status - NA.
Ford Fuel System :: 1988 - Got Code 41 - Lean Miss At Idle - ECM Or Injectors?
1988 F250 351 5.8
I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.
The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?
Ford Ranger / B-Series :: 2003 - Missing On 3 Cylinders Randomly / Lean Fuel
2003 Ranger (4.0 L-2wd)...
Codes - random misfire and cylinder banks 1, 2, 3, reads out lean fuel
Will be checking out injectors and rail pressure, however, trouble shooting in general for this issue.
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.