Ford Transmission :: E4OD Won't Shift Into Any Forward Gears But Reverse Works
I have a 95 F250 with 7.5 and E4OD. I was towing my Jeep and trailer out for the weekend a few months back (its been parked since) and heard some noise coming from the trailer. So at a stop light I put it in park with the engine running for a second, went to put it back into drive and it hasn't gone back into drive since. Reverse works perfectly. Fortunately I was able to back up onto the center divide, unload my Jeep and back the truck onto the trailer and tow home with my buddies Chevy. Anyways, its been dead since. Where I can start to look? None of the forward gears work at all.
View 13 RepliesSonata NF (2006-10) :: Dies When Switching From Forward To Reverse And Vice Versa
My sonata 3.3 dies when switching from forward to reverse and vice versa. Suspecting the fuel pressure regulator. Have seen conflicting sites saying its on the firewall and some saying in-tank. What else may be causing this.
View 2 RepliesSubaru - Outback :: 1996 - Engaged Reverse While Moving Forward
Yesterday I reversed my 1996 Subaru Outback (manual transmission) out of a perpendicular parking place on a hill, swung around forward and coasted down the hill. Near the bottom, I let out the clutch out without realizing I was still in reverse gear. It made a not-so-awful noise (sounding rather like engine braking) and I very quickly put it in neutral. I immediately smelled a fairly strong gasoline/exhaust aroma and the engine stalled.
The Subaru restarted without trouble, but the check engine light was on. Everything appears to function normally now, and I've reset the engine light by disconnecting the negative terminal of the battery for a few minutes.
Have I likely damaged anything? Is there anything I should check? Should I have tried to read the diagnostic code?
S-10 :: 98 Tanny Shift Into Gear But Wouldn't Go Forward Or Into Reverse
My son called me today to pick him up. His 98 S10 would shift into gear but wouldn't go forward or into reverse. New clutch 6 months ago, hoping something simple like low gear oil or worse?
View 1 RepliesElantra XD (2001-06) :: 2005 Doesn't Go Forward At All If Shift Into Reverse And Then Go Back Into Drive
I recently bought my '05 Elantra from a small dealership and I'm starting to see a problem with it. If I shift into reverse and then go back into drive, the car doesn't go forward at all. I have to mess with the gear shift a bit to get the car moving. I'm pretty sure it's a bad linkage. The dealership I bought it from said it desperately needed motor mounts when they got it so they replaced 2 of them. I'm sure the problems are related. I can't find any information on replacing it myself though.
View 1 RepliesFord - Mustang :: Creep Forward When Stopped And Depress Brake Pedal Firmly
I have a 2003 Mustang. The front brakes are new, and back brakes are OK. When I stop at a stop light, and depress the brake pedal firmly, the car continues to creep forward. I have to put it in neutral or park to get the car to a standstill.
View 10 RepliesFord - Mustang :: 1986 LX Dies When Key Is Released
Okay so i have a 86 Ford Mustang LX 3.8L v6 so i have a brand new starter, starter solenoid and ignition lock cylinder installed all not even a half a week old so my issue is when i go to start my car it cranks over just fine and fires up when i release the key to just let it run it instantly dies it will run if i just fine if i hold it in place, what it could be and that's ignition switch in steering column ...
View 19 RepliesFord - Mustang :: 2001 - Dies While Driving?
My 01 mustang gt which I have never had any problems with, well one day while coming home from school out of nowhere it didn't want to start at all ,all it did was a "clank" noise and I thought it was the battery so I got a friend to pass me cables but it still didn't start , but its a stick shift and I know that most of the time they start with a little push and it turned on and I was able to make it home but when I tried turning it on again it would just make a "clank" noise so I assumed it was the starter so I replaced it but it still didn't start so I went ahead and bought a new battery and now it started ,so I thought the problem was fixed but the next day around 7pm after using it for a while throughout the day all my electrical power shut down even my dashboard didn't mark anything but the car kept running until I made it home so I turned it off and tried turning it back on but it wouldn't start like the battery didn't have any power to make it start because the engine was trying so I left my battery charging for a couple of hours and it turned back on so I tried going to the corner store today but now my car shut down completely it left me on the middle of the street i got a friend to pull me and when I got home I charged my battery again and it runs again so I thought ok this has to be the alternator so I removed It and took it to O'Reilly auto parts and got it tested but it passed the test they told me it was good so what it might be ?
View 18 RepliesFord - Mustang :: Replaced Clutch Now Car Won't Shift Into Gear
So I just put a new clutch in my 01 Mustang with the baby 3.8l engine and a 5 speed T5OD transmission. The car will shift through all gears fine when turned off, but when I start it in neutral and push the clutch in, it won't shift into any gear. I can start it in first gear though with the clutch pedal in and it moves forward VERY slowly. The trans has enough fluid, and I already pulled up on the pedal to self adjust. Not exactly sure what else could be wrong.
View 19 RepliesFord - Mustang :: 2005 GT Automatic Transmission / Shuddering When In Reverse
I'm a proud owner of 2005 Mustang GT, 4.6L with an automatic transmission. Intermittently for the last year or so (maybe once every 3 or 4 months) its been shuddering when in reverse. Today it ramped things up a notch. :-/ The shuddering was pretty dramatic when I was trying to back out of my driveway, I shifted into park for a moment, then back into reverse, and it seemed to be ok. Then when trying to back into a parking spot this afternoon at work (in a parking garage with a small incline) it lost power almost entirely in reverse, lightly pushing on the gas just caused the car to shudder and not move anywhere. I shifted into park, and then back into reverse and heard an audible "pop" (my windows were down, but they hadn't been earlier so I'm not sure if this happened in the morning) and the car did not want to reverse. Rather than risk further damage I decided that it was parked relatively ok (90% in the space, eh good enough) so I stopped.
View 4 RepliesFord - Mustang :: 2001 Won't Shift Into Gear After New Clutch Installed
This is on an 01 Mustang with the baby 3.8l and a T5OD tranny. I installed a new clutch and now when the car is on, it won't shift into any gear. But I can start the car in gear and let go of the clutch and it moves forward just fine. I took everything back apart and checked the clutch plate and it is in there correctly. The clutch fork is completely on the little pivot ball.
The throw out bearing is the same size and everything as the old one. I pulled up on the clutch pedal to self adjust. Still not going into gear when the car is on.
I have heard that I might have air in my clutch line. But this clutch is cable actuated, not hydraulic. I have no master cylinder. Like I said before, I already pulled up on the clutch to self adjust and still no luck.
Ford - Explorer :: 1996 - Clicking Sound Then No Forward Gears?
I have a 96 explorer (Eddie Bower Edition) with automatic trans ( not sure which one at this moment)....
Today getting on the freeway as I was getting up to speed I heard what sounded like a click then no longer had any forward gears. After rolling to a stop I tried every gear and nothing I did fell like it wanted to go but it would not move.
The trans fluid did not smell burnt and at most I might have been maybe 1/2 quart low. Where to start and what to check?
Ford Transmission :: 4r70w - No Forward Gears Only Reverse
I have a 98 expedition with a 4.2 liter 4x4 and what I believe to be a 4r70w transmission (u code on the door sticker)
The original transmission went at 105k miles and was replaced with a new factory ford transmission by a ford dealer 3.5 years ago. The new transmission only has 10k miles on it.
Now the new transmission only has reverse. reverse works like normal but no forward gears. the idle will change when i put if in gear, but will not move, acts like it is in N . There is no strange noises.
It's hard to believe a new trany is shot already, no towing, or off road use.
My question is : is there ANYTHING that can go bad that would cause this? The trany fluid is clean and clear bright red, and no burnt smell.
I want to check everything I can before calling a tow truck to have it looked at. I will have it repaired if needed, but I don't think I want to replace another tranny.
Ford Transmission :: 4R100 Grinding - Now No Forward / Reverse?
A friend just bought a 99 Navigator, with what wikipedia says is the 4R100. Previous owner allegedly rebuilt the trans but used the old converter
It was apparently slipping a bit, or something, when he got it. Then on the way to my place so I can drive it and see what I think, it started making nasty grinding noises once he hit 4th gear. He got off the highway and made it to my place just fine.
Put it reverse to turn around in my driveway and it started the grinding noises again. Forward gears initially had some grinding as well after that, with no forward motion. Now there's no grinding, and the engine free revs in any forward/reverse gear
Fluid is full, still red, but smells nasty.
I don't suppose the three feed bolts above the valve body being loose would cause this? I imagine he's looking at a rebuild, which neither of us really want to do.
Ford F-150 (2004-2008) :: 2006 - Reverse Only Will Not Go Forward?
I just purchased my 06 f150 about 6 months ago, now I am experiencing some issues!!!!! my reverse works fine but it will not go forward in any gear? nor 4 wheel, that leads me not thinking its the transmission but ppl have said otherwise including mechanics! i did get codes p0174 and p2106 throttle body p0720 put put speed circuit!!!!
View 6 RepliesFord Transmission :: 4r100 Will Now Go Into Forward Gear But No Reverse
Early 2000 F250
Originally the truck would not go into any forward gear, but had reverse all day long. So I had a rebuild kit ordered (new bushings, seals, frictions, steels, a washer and flat bearing kit, a sprak kit, and the od piston)
After rebuilding it, taking my sweet time double checking everything, it will now go into forward gear but not reverse. So I dropped the pan. The small 3 bolt plate was torqued to spec. When I got to the third bolt in the smaller section of the valve body (upper valve body) I heard a click like maybe a valve returned to its place but I'm not sure. I removed the valve body and accumulator and all the valves were free and had tension. When I had it apart the first time one valve stuck for a split second but I never could get it to stick again.
Finding nothing there I uninstalled the tranny and took the barrel apart all the way down to the L/R piston and could not find anything wrong.
After the build and me running the truck for about 10-20 min there was metal on the magnet (part of the reason I took it all back apart) however I could not find anything worn or chewed up. Could have been the tc I prefilled with 2 quarts in stead of filling all the way.
When I initially rebuilt the 4r100 I took apart the pump to replace the bushing and seal but did not take apart the valves. I've heard the pump is directly related to reverse but I'm not sure. Could something gone wrong in the pump when I took it apart? How would I know? If I new all parts of the reverse system I could then test them.
Ford F-150 - 1997-2003 :: Transmission - No Forward Gears Or Reverse
The truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 RepliesFord Ranger / B-Series :: 2000 - Won't Move Forward Or Reverse?
2000 ranger v6 automatic trans electronic 4wd shift on the dash. Plowing snow all of the sudden lost both forward and reverse never slipped or made any noise. Transmission fluid is fine to the level and clean. Put in drive nothing and reverse nothing put it back in park you can hear the park paul trying to click in. Towed it back to the shop thinking maybe the transfer case was junk. Decided to check the actuator on the transfer case no power going to it, go back to the switch no power there either check the fuses both are good and have power. The question i have is could a bad GEM module cause all this? ps the windshield wipers do work.
View 6 RepliesFord Transmission :: 1999 F350 - 4R100 Won't Go Forward But Has Reverse?
I don't know why... It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problemo, then when put it in Drive it revved like it was in neutral.
There was no banging, no clunkin, nothing to make it seem like something catastrophic happened. I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more.
Next I did the obvious and checked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new. I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
I am on a tight budget and working on my back. I am willing to take the tranny out and bring it into town. Personally I think it's electronic but I don't know ...
Why THis thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings?
Can this be a "worn out" valve? or gasket issue? I really want to avoid removing the tranny at all costs so if there is something I am missing let me know and if you think just yank it out I will.