Ford - Mustang :: 1986 - Engine Will Start Searching / Idling Up Down And At Time Stall
I love my '86 Mustang GT convertible. Currently at 106,000 miles and running strong. The problem is searching at idle. I have replaced every sensor that me and my mechanic can think of. New plugs and wires along with rotor and distributor cap. The engine will start searching, i.e. idling up and down, and at time stall. If I apply slight pressure and idle up to 1,000 RPM the searching stops. Hard to do sometimes as this is a stick.
View 4 RepliesFord Ranger / B-Series :: 1988 2WD Dies When Clutch Is Released
My Grandpa has an 88 Ranger 2wd with the 2.9l V6 and a 5 speed, I believe, M5od. I was driving down the highway when I heard a noise. I tried throwing the tranny in neutral but when I pressed the clutch pedal in, I had no pedal whatsoever. Engine took awhile to restart. It'd turn over a little almost as if a rod was bent or something of the sorts. Eventually the engine started and would stay running as long as the clutch was pressed in (disengaged).
The engine dies no matter what range the transmission is in,neutral included unless the clutch pedal is depressed. It Will die when the clutch is released in any gear with no forward movement that is noticeable. I can spin the tail shaft with the driveshaft installed and all gears in neutral but the input does not spin at all. Input shaft wont spin at all, period. I originally thought the slave cylinder was KIA but now I am very confused on what the problem could be? Is there a bearing the input shaft rides on that may of seized?
I pulled the tranny last night and took the top cover off. Yes, I made sure it was in neutral when I removed the cover. I can manually shift the collar to all gears by hand, 5th and reverse included. I'm stuck between a rock and a hard place here and where to go from here. I have bought a new clutch assembly and slave cylinder. This truck was bought by my Grandpa brand new in 1988. It has 98,000 miles and everything is original. I did forget to mention that there was very little oil in the trans when I drained it and it appeared to be gear oil vs ATF.
Ford - Mustang :: 2001 - Dies While Driving?
My 01 mustang gt which I have never had any problems with, well one day while coming home from school out of nowhere it didn't want to start at all ,all it did was a "clank" noise and I thought it was the battery so I got a friend to pass me cables but it still didn't start , but its a stick shift and I know that most of the time they start with a little push and it turned on and I was able to make it home but when I tried turning it on again it would just make a "clank" noise so I assumed it was the starter so I replaced it but it still didn't start so I went ahead and bought a new battery and now it started ,so I thought the problem was fixed but the next day around 7pm after using it for a while throughout the day all my electrical power shut down even my dashboard didn't mark anything but the car kept running until I made it home so I turned it off and tried turning it back on but it wouldn't start like the battery didn't have any power to make it start because the engine was trying so I left my battery charging for a couple of hours and it turned back on so I tried going to the corner store today but now my car shut down completely it left me on the middle of the street i got a friend to pull me and when I got home I charged my battery again and it runs again so I thought ok this has to be the alternator so I removed It and took it to O'Reilly auto parts and got it tested but it passed the test they told me it was good so what it might be ?
View 18 RepliesFord - Mustang :: 1996 - Dies When Shift To Forward Or Reverse
I have a 1966 Ford Mustang 2 + 2 (289 cu. in.) V8 with four barrel carburetor. It has more than 170K miles on it. It starts right away, but when I shift the automatic transmission to reverse or forward it dies out every time. I changed the fuel pump and the fuel filter, but the problem persists. I have had this car for almost 46 years now and I cannot bear to part with it.
View 2 RepliesChevrolet - Camaro :: 1986 - Car Dies After Warm Up
I recently purchased for my son a 1986 camaro 2.8 MFI v6 the car had been sitting for over a year in the previous owner's back yard because it would not start.I have had a mechanic do the following: heads redone, replace the distributor, replace the timing chain and gears, new wires, and emptied the fuel tank and replaced the fuel filter.
I picked up the car and it ran for about two week no problem. Then it started diying occasionally when you let of the gas to come to a stop, so he replaced the fuel relay switch thinking that it may be going bad. The next day he had been driving it about 15 miles when it just died and would not restart. We shot a little starting fluid to see if we could get it to start and get it back home. it fired up and ran all the way home and died when turning into the driveway. and would not start again.
We replace the fuel regulator the car started right up and he took it for a test drive. The car ran about 4 miles, long enough to warm up and died again and would start. and again we were about to get it started with starting fluid to get it back home. pulled in the driveway and it dies. again it would not start, let it sit all night and the next morning still would not start finally got it to start with a squirt of starting fluid and moved it into the garage. shut if off and then tried to start it and it worked 5 times in a row.
Ford - F150 :: Clunking Noise While Brake Is Released?
My ford F-150 makes a clunking noise when I release the brake at a stop light or stop sign. It sounds like it is in the transmission. It only happens when I come to a complete stop and start moving again.
View 4 RepliesFord - Thunderbird :: 1979 V8 Suddenly Not Starting / Engine Turns Over But Stalls When Key Is Released
I have a 1979 Ford Thunderbird with a V8 5.0 liter engine. Here's the mysterious problem... the engine turns over when I turn the key but stalls when the key is released. Thinking that the alternator died, I replaced it with a new re-manufactured unit and the car's symptoms stayed the same. Also checked the fuses and the fuel filter and found that plenty of fuel is getting to the carburetor. This issue with the car not starting appeared literally overnight after I attempted to install a new radio. Prior to this the car ran reasonably well – always started easily and ran without a problem. Wondering if there is a possibility that I fried some part of the electrical system when I fussed around with all the wiring under the dash. Someone else had attempted the radio installation previously so the wiring there was already a mess of cuts and re-connections and was hard to sort out.
View 7 RepliesFord Super Duty (1999-2016) :: 2000 - Engine Shuts Off When Key Released?
I have a 2000 F-250 with a 7.3l turbo diesel.
It's been running great but recently I've noticed an issue with starting.
When I turn the key and the engine starts when I release the key it's like the engine stops for just a second and then starts running again.
After it's started it doesn't seem to have any issues but I'm concerned and would like to nip it in the butt before it because of a real issue.
Ford 7.3L Power Stroke (1999-2003) :: F350 Stalling When Accelerator Pedal Is Pressed And Released
I have an issue with my 1999 Ford F350 7.3L diesel and stalling when the accelerator pedal is pressed and released.
Background: Initially the truck would not start, and from there here are all the things that I found wrong and replaced. (keep in mind that I troubleshot all the issues and every part that was replaced was proven faulty)... Starting with the glow plugs, all but 3 were faulty and not making a connection to ground. (only one broke off in the head, but I was able to get it out with out getting anything in the cyl)..
Valve cover gasket and harnesses, this is to include replacing the connectors on the engine harness cause both sides of the connectors were broken. The ICP was leaking into the connector and breaking the connection to the PCM, so the connector was cleaned and the sensor replaced. No issues from that now.
The IPR was replaced cause the oil pressure was erratic and not stable when I had my pressure gauge hooked up testing the pressure. After that was replaced the pressure was ok, and it climbed with RPM's and fell back down like it was suppose to. I could not get the PSI up to 3000 PSI even at full RPM's, but it did not drop past 600 psi.
The fuel tank was recently replaced, and all the fuel was removed and "fresh/good" fuel was put in. The fuel bowl was cleaned out and the filter replaced. (the fuel bowl did have a lot of crap in it like rust and dirt). Fuel pressure was at 95 PSI last time I checked, which is higher than the recommended 60 to 65 PSI.
That being said the engine did start and run, but was very rough and missing. So I did all the injector o-rings. Some o-rings were starting to split, and others were not sealing like the copper washer on the injector tip. I could tell by the amount of crap in the end of the injector. ( not the tip, but where the injector contacts the injector cup. There must have been water in there or something cause that part had all kinds of crap around it)
The engine smoothed out after a couple day of running it, but it would still stall when it was cold. The block heater was replaced cause it was falling out. The oil was changed and the filter too. The CMP sensor was changed just because I know they will cause the engine not to start. I had a "known good" truck that I can swap part to and from, and I did a lot of that thus far.
Swapped the IDM, PCM, EBP sensor, MAP sensor, all relays inside the engine and in the cab. I was looking for the barometric pressure sensor, but from what I have read thus far that is a calculation in the PCM between the MAP and the EBP sensors. The diode to the PCM is good,I checked the harness for rubbing by the 42 pin connector and by the LF fender but I did not find any chaffing or rubbing on any wires. The ECPR was wired together, so I fixed it so that it is no longer that way, and the waste gate for the turbo was wired open. I took the wire off and made sure the linkage worked and it did move. I tried to lube up the valve in the turbo for back pressure, but I'm not sure if it worked or not.
I also swapped out the oil pressure sensor and the oil pressure temp sensor on the HPOP Reservoir, and blew out the EBP sensors tube. (air went straight through the tube with no restrictions.) I did a buzz test and all the coils checked out ok. I also did a contribution test and only three cylinders were identified as having some kind of issue. (but this is not enough to cause the engine to stall..) The only current codes that I have are the air intake heater, and the EF feedback not detected. Neither of which would cause the engine to stall in my opinion.
Symptoms:
When cold: The engine will start and idle just fine, but when the accelerator is pressed and held to 1000 RPM's the engine will sputter like its missing and surge up and down between 500 and 1100 RPM's. If the accelerator pedal is pressed quickly the engine speed to increase then fall down and stall. It seems as if the PCM is shutting down and starting back up. ( Like the key is turned off and then back on quickly, but the engine doesn't recover)
When warming: This issue becomes more erratic, but when hot the engine is fine. No issues, and it will drive all day long with no hesitation.
The truck has over 200K on it, but I know it will go more! It is a mannuel tranny, and is a 4X4, and I love it, I can't get ride of it just yet.
1993 Ford Mustang GT 5.0 Will Not Go Into 2nd Gear
My 1993 Mustang GT 5.0 will not go in to 2nd gear. It's the AOD and it goes into 1st, 3rd and OD just fine. I've heard there a pressure bolt that set the pressure in the trans and that it may be why I can't go into 2nd. And I've also heard that my TV cable may be stretched.
View 1 RepliesFord - Mustang :: 1989 GT Starts Without Key
I noticed something strange the other day that my 89 GT can be started without the key ! Everything works as it should but you do not have to put the key in the ignition lock switch. I did have the ignition switch replaced many years ago when Ford had the recall due to a possible fire.. I believe the switch that was replaced is located down under the base of the steering column and activated with a rod from the column key lock.. Is it hard to replace this column lock switch ?
I would rather do it myself instead of paying a locksmith to do it..I do have an anti-start security system on it and when you enable it it locks out the ignition. To start it you have to enter a certain 5 number code for it to crank. I had this car since new and only 117k on the clock and runs like new. Where can I obtain a replacement "key lock assembly " ? This is the original key lock on the column..Just worn out I guess . Only thing I replaced on this car was a new clutch due to a bad throw out bearing making noise at 80k and a water pump and serpentine belt at 90k and a noisy fuel pump. Still has the original prone to failure ignition control module.
Mustang :: 1998 Ford V6 Always Shifted Odd Into Overdrive
I have a 1998 ford mustang v6 automatic with 79k. I've owned it for 8 years and it has always shifted odd into overdrive. If I take my foot off the gas it will go into overdrive but not the smoothest. Should I start with a fluid flush? It shifts great through all other gears.
View 1 RepliesFord :: 1968 Mustang 289 Turns Over But Won't Start
I've had my car sitting for 3 weeks and went out this morning to start it and it turns over but won't start. It has fuel and the battery seems to be providing enough power to the starter. It ran fine 3 weeks ago and I have not done any repairs recently that would be cause for the problem, I also changed the oil a month ago.
View 8 RepliesFord - Mustang :: 2001 GT Cranks But Won't Start
it's been parked for about 2 months in my driveway, which slants upwards. I cranked it for a solid 30 minutes (jumped the battery so it wouldn't die). I don't smell gas so I think gas isn't making to the motor.
View 1 RepliesFord - Mustang :: Losing Power When Braking
Sometimes when I brake to come to a stop, my car loses power: the whole thing shudders, RPMs take a dive. It doesn't start immediately on braking. It starts when I am almost at a stop, but not at a full stop. If it's relevant, I generally brake quite gradually, starting several car lengths away. So there are several seconds between onset of braking and onset of power loss. It starts while the brake is depressed. It does not stop when I let up on the brake. It does stop when I depress the accelerator. If I am idling at a light, it might happen. If I am just going slow without braking, it doesn't happen. Braking is fine in all circumstances except coming to a full stop.
Details:'93 Mustang, 4-cyl, 2.3L, manual, fuel-injected
It's been doing this for years, actually, and yes, I've been just dealing with it instead of getting it checked out. Usually a little rev of the engine gets her through it. Last night, it actually stalled, several times in fact. It restarted, but it did take cranking it for a while for it to restart.
Now that I think about it, my battery might be up for replacement. It's probably around 7 years old, and the last 6 have been very light driving, maybe 3k per year. But like I said, this is an ongoing problem. What should I be thinking about besides the battery, and what is a mechanic likely to tell me?
Ford - Mustang :: 1995 - Starts For About 1 Second When Cold Outside
I have a 95 Ford mustang GT. When it is cold outside (Below 40 ish) it starts for about 1 second, dies abd the second time starts fine. has check engine light for lean exhaust. vacume pressure fine and been using injector cleaner but no improvement. replaced spark plug/ wires pcv valve.
View 5 RepliesFord - Mustang :: 1967 - Overheating Only While Driving
This car has me stumped I've got a 67 mustang that is overheating only while driving I've replaced the radiator new 180 thermostat facing the proper way bypassed the heater core replaced the head gasket flushed the cooling system but after running vehicle for ten to fifteen minutes one side of the block is reading 178 degrees the other side is reading 240 in lost.
View 19 RepliesFord - Mustang :: 1967 - Car Repeatedly Won't Start
I have a 1967 Ford Mustang. I drive in mainly on the weekends. The carb is rebuilt within the last six months. I installed a new alternator about a month ago. The battery was leaking and so the car stopped running one day. I just put in a brand new battery. It still won't start. It feels like it's trying to start but just won't turn over. I did clean the terminals and lubricated them as well when I installed the new battery.
View 1 RepliesFord - Mustang :: A/C Is Cold Until The Fan Is On High Then Warm Air Comes Out
When the a/c fan is on any setting other than the highest setting the air comes out cold. When the fan is set to the highest setting, it only comes out warm. This happens regardless of a/c or max a/c setting, regardless of fresh or recirculated air, and regardless of car speed. (2005 Mustang GT)
View 9 Replies