Ford Transmission :: 4R100 Grinding - Now No Forward / Reverse?
A friend just bought a 99 Navigator, with what wikipedia says is the 4R100. Previous owner allegedly rebuilt the trans but used the old converter
It was apparently slipping a bit, or something, when he got it. Then on the way to my place so I can drive it and see what I think, it started making nasty grinding noises once he hit 4th gear. He got off the highway and made it to my place just fine.
Put it reverse to turn around in my driveway and it started the grinding noises again. Forward gears initially had some grinding as well after that, with no forward motion. Now there's no grinding, and the engine free revs in any forward/reverse gear
Fluid is full, still red, but smells nasty.
I don't suppose the three feed bolts above the valve body being loose would cause this? I imagine he's looking at a rebuild, which neither of us really want to do.
Ford Transmission :: 1999 F350 - 4R100 Won't Go Forward But Has Reverse?
I don't know why... It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problemo, then when put it in Drive it revved like it was in neutral.
There was no banging, no clunkin, nothing to make it seem like something catastrophic happened. I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more.
Next I did the obvious and checked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new. I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
I am on a tight budget and working on my back. I am willing to take the tranny out and bring it into town. Personally I think it's electronic but I don't know ...
Why THis thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings?
Can this be a "worn out" valve? or gasket issue? I really want to avoid removing the tranny at all costs so if there is something I am missing let me know and if you think just yank it out I will.
Ford Super Duty (1999-2016) :: F250 - 4r100 Transmission - No Forward Gear?
I have a 1999 ford f250 5.4 2 wheel drive i believe its a 4r100 transmission. auto. I have reverse but no forward gears. Ive heard this is a common problem , and on my reverse it has to hit 3000 rpm before it even tries to move and D 1 2 i have nothing only thing i hear is the engine sound changes gets deeper. Do i need a whole new transmission or is this fixable.
View 4 RepliesFord Transmission :: 4R100 Nearly Stalls In Reverse
I have 2001 E350 Van. One quirk.... When I put the van in Reverse, the engine drops to very low RPM and nearly stalls. This does not happen in Drive.
Transmission is out for repair now for other reasons (for a damaged pump). What can cause this near stalling? What do I look for as far as cause & repair?
Ford Transmission :: 4r100 - No Reverse After Rebuild
I rebuilt my 4r100 myself. 1st time I re-installed it, I had no 2nd gear. All other gears worked fine. Drove it less than 2 miles.. slowly..
Took it back out, found i built the Intermediate Clutch wrong. Fixed. At the same time, found a stuck valve in the accumulator VB, Fixed that, at least i think I did. all the valves snapped back under spring pressure.
Put the trans back in, Drove forward, all forward gears work. Drove 10 miles normally, w/ some time spent in all speed ranges. Temps good, outside temp was 73F
M1 = i get good engagement and engine braking
M2 = I get 1st and 2nd, seems normal
OD = Normal shifts, 4th is a little soft, but always was.. TCC lockup good
OD (Cancelled) = Normal 1-2-3, with lockup in 3rd Worked the button multiple times, shifts down, and back up normally.
N = No movement, no creeping.. Normal.. as far as I can tell.
R = No reverse, or is binding in reverse, not sure. worse when up to temp.
P = Normal, no learching or creeping.. No stalling.
The OD light never blinked, so I don't think it is electronic..
Since M1 works and holds with engine braking. L/R clutch and seals are ok. Forward clutch is ok since i have ALL forward gears, No slipping that I can tell. no creeping in Neutral, so the clutches are not fried.. New fluid is still perfect. I'll have to re-pull the pan to see if there is anything on the magnet. I think it could be some stuck valves in the VB also.
Ford Transmission :: 4R100 Shudder In Reverse Combined With A Noise
A few days ago, I was trying to back up with my 5th wheel (12,000lbs) and in reverse the transmission was shuddering combined with a noise. So I stopped and since than, the reverse is shuddering when I accelerate.
If I put it in reverse and let it in idle, everything is fine. The forward gears without problem.
Temperature always between 140 and 160, never overheated.
F350 Dually Crew cab, 7.3, 1999, 215,000 km, superchip,
Never overdone it with the power. Fluid level ok, no burned smell at the fluid, still red in color.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - 4r100 Transmission - No Reverse
my parents have a f350 which now has no reverse. it has a reman sticker on it, 230k on the truck but no idea on mileage on the tranny. shifts 1st through 4th fine, no slip. Tc lockup works just fine. No codes found with my solus scanner. When shifted in reverse it will move back about 2 ft if revved above 2k and then nothing. Am I looking a trans rebuild or is there something I can check and repair with in it the truck?
View 4 RepliesFord Transmission :: 4r70w - No Forward Gears Only Reverse
I have a 98 expedition with a 4.2 liter 4x4 and what I believe to be a 4r70w transmission (u code on the door sticker)
The original transmission went at 105k miles and was replaced with a new factory ford transmission by a ford dealer 3.5 years ago. The new transmission only has 10k miles on it.
Now the new transmission only has reverse. reverse works like normal but no forward gears. the idle will change when i put if in gear, but will not move, acts like it is in N . There is no strange noises.
It's hard to believe a new trany is shot already, no towing, or off road use.
My question is : is there ANYTHING that can go bad that would cause this? The trany fluid is clean and clear bright red, and no burnt smell.
I want to check everything I can before calling a tow truck to have it looked at. I will have it repaired if needed, but I don't think I want to replace another tranny.
Ford 7.3L Power Stroke (1999-2003) :: 4R100 Transmission Will Only Shift To 2nd Gear When Throttle Is Feathered At 2500 RPM
Problems with my 2001 F250 4r100 transmission. Transmission will only shift to 2nd gear when throttle is feathered at @2500 rpm. All other gears shift perfectly. This problem is consistent.
View 10 RepliesFord F-150 - 1997-2003 :: Transmission - No Forward Gears Or Reverse
The truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 4r100 Transmission Loose After Warm Up Especially At 4th Shift Overdrive And Passing Gear
I have a 4r100 on in a 99 7.3 4x4. The shifting problem I have appears to be intermittant. it seems loose after warm up especially at the 4th shift overdrive and passing gear. possibly due to low presures ? sometimes (lately more often than not) hunts back and forth between 4th and o.d when passing or hill climbing. Under normal driving it shifts somewhat firm with 4th being an exeption.I have changed my crank position sensor filters and fluids which had turned dark and improved slightly. When I pulled the pan and replaced the filter the pan was spotless. No residue or signs of plates or debris. There is about 100,000 miles on the tranny and 350,000 on the truck. Questions: Is there a tcm for this transmission and if so could it cause these problems? I'm considering a purchase of an unlocked 1705 superchip to change the shifting but unsure if this will work for my issues...
View 14 RepliesFord Transmission :: 1999 F250 4x4 Automatic - No Forward Gears Only Reverse?
I recently bought a decent looking 1999 f250 4x4 5.4 auto. It has no forward gears and will only move in reverse. I topped off the fluids and have found no leaks so far the cooler lines are crusty but dry. I am gonna need to swap this thing out or do some more trouble shooting if there may be a non rebuild issue to solve.
View 4 RepliesFord Transmission :: E4OD Won't Shift Into Any Forward Gears But Reverse Works
I have a 95 F250 with 7.5 and E4OD. I was towing my Jeep and trailer out for the weekend a few months back (its been parked since) and heard some noise coming from the trailer. So at a stop light I put it in park with the engine running for a second, went to put it back into drive and it hasn't gone back into drive since. Reverse works perfectly. Fortunately I was able to back up onto the center divide, unload my Jeep and back the truck onto the trailer and tow home with my buddies Chevy. Anyways, its been dead since. Where I can start to look? None of the forward gears work at all.
View 13 RepliesFord Transmission :: Loud Chirp - No Reverse / No Forward Gears On 5r55e
The other day I was leaving my house. I started the car and heard a quick, loud chirp. That was the only noise it made so I continued to leave. I rolled out of my driveway and proceeded to put it in drive and found myself rolling backwards. I tried every forward shift, kicked on the 4x4 and continued to roll backwards. I thought reverse worked but found that it wasn't engaging either. My question: is there anything I can look at before resorting to taking it to the tranny shop? I'm in school for automotive and am confident in my abilities to test solenoids and maybe even dropping the valve body to check that. Other than that, I lack the skill to pull the tranny myself and work on it.
View 3 RepliesFord Transmission :: 1999 - No Forward Or Reverse Gears / Black Trans Fluid
My 1999 7.3l Disel 4x4 transmission quit on me the other day. No forward or reverse. Got towed to my regular repair shop, and they are treating the transmission as a black box and recommending total replacement. The diagnostics they performed were to make sure it was shifting, and that indeed it wasn't going forward or reverse. They drained the fluid and said "it's pitch black" and said it had to be completely replaced.
Fluid level was OK, and it wasn't hot. I was driving along, and merging onto the highway. It downshifted, shuddred, and nadda. Free rev. I coasted to the next exit and into a parking lot. Verified that it was shifting, checked Rev and all forwards. It wouldn't shift into 4W, and 1-2 also wouldn't move.
I'm trying to figure out what might have happened... and if it's worth trying to have the truck towed to a transmission shop and have them diagnose and rebuild, vs just getting a remanufactured transmission. None of the local wreckers have any used transmissions, and the cost between a reman and a used is pretty negligible...
Not sure what the symptoms points to for exact failure mode, be it the torque converter, pump, input shaft, etc... I've never had an automatic transmission apart before, but built plenty of motors and am a machinist by trade. My preference is to try and root cause the failure...
Ford Super Duty (1999-2016) :: F350 - Transmission Won't Go Forward But Has Reverse?
It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problem, then when put it in Drive it revved like it was in neutral. There was no banging, no clunking, nothing to make it seem like something catastrophic happened.
I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more. Next I did the obvious and cheked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new.
I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? Ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check ***** were in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
Why this thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings? Can this be a "worn out" valve? or gasket issue?
Ford Super Duty (1999-2016) :: Screeching Sound Only Happens When In Gear (auto) Moving Forward Or In Reverse
My 2001 F250 5.4 has started to make a screeching sound. It only happens when it is in gear (auto) moving forwards or in reverse, and increases in pitch relative to engine speed rather than road speed, and is much more noticeable under mild to moderate acceleration. Maybe I actually mean transmission input speed?
When simply maintaining road speed, it is almost silent. Anyway, if I drop it into neutral while driving, the sound stops, and starts again when I put it back into gear.
From the drivers seat and with the windows closed, it sounds as though it is coming from the engine bay at steering column height, although this is really tough to gauge while actually looking where I am going. With windows open, it comes from both sides of the vehicle.
1st thought is tranny......
2nd thought is a water pump bearing, although there are no apparent cooling problems or leaks.
3rd thought is the alternator bearing, although there are no charging problems.
I say alternator because I recently changed the serpentine belt and noticed that the alternator made a very faint screech-like sound when spun without the belt on it. The main screech was there before I changed the belt. Maybe it gets really loud under load?
So I'm kinda scratching my bean and wondering what expensive piece of mechanics I'm going to shell out for next. If it's #2 or #3, I can do those myself, but if it's #1.... it likely means more money than I have to spare.
I did wonder about removing the serpentine belt and driving a very short distance (end of the driveway and back) to see if I can remove the pulleys, tensioner or other belt driven parts from the equation. Maybe this is not such a smart idea. I'm somewhat at a loss right now.
1998 Chevy Blazer Won't Go In Reverse But Will Go Into Gear Going Forward
I have a problem with my 1998 Chevrolet Blazer. It won't go in reverse, but will go into gear going forward. I don't know whats wrong or what the cause is.
View 2 RepliesCamry :: 2009 LE - Rolling Forward While In Reverse Gear
I just purchased an Automatic 2009 Camry LE with 64k 2weeks ago, and noticed that twice it felt like it was losing power on an incline so I bought the fuel system cleaner to see if that worked (seaform). Tonight I go to park it on a street with a slight incline. As I shift to reverse to line the car up, it rolled forward. It shocked me bc there was a parked car right in front of me. I tried putting it in Drive/Park etc then back in Reverse it still rolled forward. I put my foot on the brake and gas at the same time to try to reverse but not wanting to give it too much gas bc I was scared it might fly forwards into the car in front of me (still rolled forward). Finally I was so close to the car in front of me I gave it a try and it still rolled and bumped the truck in front of me but with enough gas it went into reverse.
View 6 Replies