Ford Transmission :: 4r100 Will Now Go Into Forward Gear But No Reverse
Early 2000 F250
Originally the truck would not go into any forward gear, but had reverse all day long. So I had a rebuild kit ordered (new bushings, seals, frictions, steels, a washer and flat bearing kit, a sprak kit, and the od piston)
After rebuilding it, taking my sweet time double checking everything, it will now go into forward gear but not reverse. So I dropped the pan. The small 3 bolt plate was torqued to spec. When I got to the third bolt in the smaller section of the valve body (upper valve body) I heard a click like maybe a valve returned to its place but I'm not sure. I removed the valve body and accumulator and all the valves were free and had tension. When I had it apart the first time one valve stuck for a split second but I never could get it to stick again.
Finding nothing there I uninstalled the tranny and took the barrel apart all the way down to the L/R piston and could not find anything wrong.
After the build and me running the truck for about 10-20 min there was metal on the magnet (part of the reason I took it all back apart) however I could not find anything worn or chewed up. Could have been the tc I prefilled with 2 quarts in stead of filling all the way.
When I initially rebuilt the 4r100 I took apart the pump to replace the bushing and seal but did not take apart the valves. I've heard the pump is directly related to reverse but I'm not sure. Could something gone wrong in the pump when I took it apart? How would I know? If I new all parts of the reverse system I could then test them.
Ford Transmission :: 1999 F350 - 4R100 Won't Go Forward But Has Reverse?
I don't know why... It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problemo, then when put it in Drive it revved like it was in neutral.
There was no banging, no clunkin, nothing to make it seem like something catastrophic happened. I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more.
Next I did the obvious and checked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new. I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
I am on a tight budget and working on my back. I am willing to take the tranny out and bring it into town. Personally I think it's electronic but I don't know ...
Why THis thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings?
Can this be a "worn out" valve? or gasket issue? I really want to avoid removing the tranny at all costs so if there is something I am missing let me know and if you think just yank it out I will.
Santa Fe (CM - 2007-12) :: 2010 - Slipping Transmission / Grinding Sound And Could Not Go Forward Or Reverse
I was driving out of a parking lot and as I accelerated onto the main road my vehicle stopped. I heard a grinding sound and could not go forward or reverse. While the car is in drive, park or reverse my car will roll any which way. It pushed it across the street. I tried to locate my tranny dipstick via visual inspection and manual. I could not find it. Could the stick have never been put back at some point in service and caused this issue. That seems unlikely but the thought occurred. Could it be the velocity joint? Whatever it is it certainly sounds like a transmission issue.
View 1 RepliesFord Super Duty (1999-2016) :: F250 - 4r100 Transmission - No Forward Gear?
I have a 1999 ford f250 5.4 2 wheel drive i believe its a 4r100 transmission. auto. I have reverse but no forward gears. Ive heard this is a common problem , and on my reverse it has to hit 3000 rpm before it even tries to move and D 1 2 i have nothing only thing i hear is the engine sound changes gets deeper. Do i need a whole new transmission or is this fixable.
View 4 RepliesFord Transmission :: 4R100 Nearly Stalls In Reverse
I have 2001 E350 Van. One quirk.... When I put the van in Reverse, the engine drops to very low RPM and nearly stalls. This does not happen in Drive.
Transmission is out for repair now for other reasons (for a damaged pump). What can cause this near stalling? What do I look for as far as cause & repair?
Ford Transmission :: 4r100 - No Reverse After Rebuild
I rebuilt my 4r100 myself. 1st time I re-installed it, I had no 2nd gear. All other gears worked fine. Drove it less than 2 miles.. slowly..
Took it back out, found i built the Intermediate Clutch wrong. Fixed. At the same time, found a stuck valve in the accumulator VB, Fixed that, at least i think I did. all the valves snapped back under spring pressure.
Put the trans back in, Drove forward, all forward gears work. Drove 10 miles normally, w/ some time spent in all speed ranges. Temps good, outside temp was 73F
M1 = i get good engagement and engine braking
M2 = I get 1st and 2nd, seems normal
OD = Normal shifts, 4th is a little soft, but always was.. TCC lockup good
OD (Cancelled) = Normal 1-2-3, with lockup in 3rd Worked the button multiple times, shifts down, and back up normally.
N = No movement, no creeping.. Normal.. as far as I can tell.
R = No reverse, or is binding in reverse, not sure. worse when up to temp.
P = Normal, no learching or creeping.. No stalling.
The OD light never blinked, so I don't think it is electronic..
Since M1 works and holds with engine braking. L/R clutch and seals are ok. Forward clutch is ok since i have ALL forward gears, No slipping that I can tell. no creeping in Neutral, so the clutches are not fried.. New fluid is still perfect. I'll have to re-pull the pan to see if there is anything on the magnet. I think it could be some stuck valves in the VB also.
Ford Transmission :: 4R100 Shudder In Reverse Combined With A Noise
A few days ago, I was trying to back up with my 5th wheel (12,000lbs) and in reverse the transmission was shuddering combined with a noise. So I stopped and since than, the reverse is shuddering when I accelerate.
If I put it in reverse and let it in idle, everything is fine. The forward gears without problem.
Temperature always between 140 and 160, never overheated.
F350 Dually Crew cab, 7.3, 1999, 215,000 km, superchip,
Never overdone it with the power. Fluid level ok, no burned smell at the fluid, still red in color.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - 4r100 Transmission - No Reverse
my parents have a f350 which now has no reverse. it has a reman sticker on it, 230k on the truck but no idea on mileage on the tranny. shifts 1st through 4th fine, no slip. Tc lockup works just fine. No codes found with my solus scanner. When shifted in reverse it will move back about 2 ft if revved above 2k and then nothing. Am I looking a trans rebuild or is there something I can check and repair with in it the truck?
View 4 RepliesFord Transmission :: 4R100 - 2000 Ford Excursion - Grinding / Vibration Occurs Between 2100 - 2300 RPMs
I have recently found what sounds like a grinding/vibration issue that occurs between ~2100-~2300 RPM's in my truck. After some googling, I thought it may be the inspection plate being a bit bent/loose. I took the cover off and drove around and the noise still occurred.
Things I have noticed:
-Occurs between 1-2 and 2-3 (had trouble with the other gear changeovers as I just have slow backroads around me to test over my lunch break- can test further in the future)
-Occurs during acceleration and deceleration
-Starts at ~2100 and ends ~2300 RPM
Any thoughts for next steps to diagnose? Truck has ~160k on it and I don't really have many service records (purchased within the past 3k miles and problem just started occurring after this past weekend). Transmission fluid seems to be in decent condition.
Not sure if it would affect anything, but I just got back from my first trip with the Excursion where I actually needed to utilize the 4WD. There was much more aggressive terrain than what it is used to seeing on the pavement. Thought I should mention that as well.
V10, if that matters (I recall reading somewhere that '99 7.3s with the auto had documented torque converter issues that warranted a TSB)....
Ford Transmission :: 4r70w - No Forward Gears Only Reverse
I have a 98 expedition with a 4.2 liter 4x4 and what I believe to be a 4r70w transmission (u code on the door sticker)
The original transmission went at 105k miles and was replaced with a new factory ford transmission by a ford dealer 3.5 years ago. The new transmission only has 10k miles on it.
Now the new transmission only has reverse. reverse works like normal but no forward gears. the idle will change when i put if in gear, but will not move, acts like it is in N . There is no strange noises.
It's hard to believe a new trany is shot already, no towing, or off road use.
My question is : is there ANYTHING that can go bad that would cause this? The trany fluid is clean and clear bright red, and no burnt smell.
I want to check everything I can before calling a tow truck to have it looked at. I will have it repaired if needed, but I don't think I want to replace another tranny.
Ford F-150 - 1997-2003 :: Transmission - No Forward Gears Or Reverse
The truck is a 2002 f150 4x4 5.4l... I was driving down the free way last night in 2wd doing about 90kpm when there was a loud bang like a ran over something. Speedo went to zero and abs light came on. Pulled over and shut it down. Crawled underneath to check so damage and couldn't see anything. Stared it back up put it in drive and it just revs. No forward gears or reverse. Fluid level is good, bright pink. Dropped the transmission pan, pan is clean and magnet has next to nothing on it.
View 14 RepliesFord Transmission :: 1999 F250 4x4 Automatic - No Forward Gears Only Reverse?
I recently bought a decent looking 1999 f250 4x4 5.4 auto. It has no forward gears and will only move in reverse. I topped off the fluids and have found no leaks so far the cooler lines are crusty but dry. I am gonna need to swap this thing out or do some more trouble shooting if there may be a non rebuild issue to solve.
View 4 RepliesFord Transmission :: E4OD Won't Shift Into Any Forward Gears But Reverse Works
I have a 95 F250 with 7.5 and E4OD. I was towing my Jeep and trailer out for the weekend a few months back (its been parked since) and heard some noise coming from the trailer. So at a stop light I put it in park with the engine running for a second, went to put it back into drive and it hasn't gone back into drive since. Reverse works perfectly. Fortunately I was able to back up onto the center divide, unload my Jeep and back the truck onto the trailer and tow home with my buddies Chevy. Anyways, its been dead since. Where I can start to look? None of the forward gears work at all.
View 13 RepliesFord Transmission :: Loud Chirp - No Reverse / No Forward Gears On 5r55e
The other day I was leaving my house. I started the car and heard a quick, loud chirp. That was the only noise it made so I continued to leave. I rolled out of my driveway and proceeded to put it in drive and found myself rolling backwards. I tried every forward shift, kicked on the 4x4 and continued to roll backwards. I thought reverse worked but found that it wasn't engaging either. My question: is there anything I can look at before resorting to taking it to the tranny shop? I'm in school for automotive and am confident in my abilities to test solenoids and maybe even dropping the valve body to check that. Other than that, I lack the skill to pull the tranny myself and work on it.
View 3 RepliesFord Transmission :: 1999 - No Forward Or Reverse Gears / Black Trans Fluid
My 1999 7.3l Disel 4x4 transmission quit on me the other day. No forward or reverse. Got towed to my regular repair shop, and they are treating the transmission as a black box and recommending total replacement. The diagnostics they performed were to make sure it was shifting, and that indeed it wasn't going forward or reverse. They drained the fluid and said "it's pitch black" and said it had to be completely replaced.
Fluid level was OK, and it wasn't hot. I was driving along, and merging onto the highway. It downshifted, shuddred, and nadda. Free rev. I coasted to the next exit and into a parking lot. Verified that it was shifting, checked Rev and all forwards. It wouldn't shift into 4W, and 1-2 also wouldn't move.
I'm trying to figure out what might have happened... and if it's worth trying to have the truck towed to a transmission shop and have them diagnose and rebuild, vs just getting a remanufactured transmission. None of the local wreckers have any used transmissions, and the cost between a reman and a used is pretty negligible...
Not sure what the symptoms points to for exact failure mode, be it the torque converter, pump, input shaft, etc... I've never had an automatic transmission apart before, but built plenty of motors and am a machinist by trade. My preference is to try and root cause the failure...
Ford Super Duty (1999-2016) :: F350 - Transmission Won't Go Forward But Has Reverse?
It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problem, then when put it in Drive it revved like it was in neutral. There was no banging, no clunking, nothing to make it seem like something catastrophic happened.
I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more. Next I did the obvious and cheked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new.
I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? Ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check ***** were in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
Why this thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings? Can this be a "worn out" valve? or gasket issue?
Chevrolet - S-10 :: 1987 - Transmission Slips In Forward Gears And Can't Go In Reverse
My '87 Chevy S-10 transmission slips like mad in forward gears and I can't go everywhere in reverse. The truck is gaaged in southern Virginia about 60 miles from my home and is used on some country property. The local transmission shop wants $1600 to rebuild the trans. He says he used sturdier parts than the replacement GM parts. I'd like to fix the truck because it comes in handy and was my dad's old mode of transportation around the Va. countryside, so it has sentimental value.
View 3 RepliesFord Transmission :: Loud Grinding Noise When Put Truck In Reverse
Chasing down a grinding noise. I have done a lot of research but nothing quit matches up with what I am hearing.
I have a 1979 F250 4x4. A few days ago I put the truck in reverse and as I was backing up it was like the drivetrain locked up. After that I put the truck in gear and started on my way. As I got up in speed a pretty loud grinding noise was coming from the tranny. 2nd and 3rd gear aren't bad but when I get up to 40+mph it sounds like crap. If I push in the clutch the grinding is still there. While driving I also put the transfer case in neutral, kept the tranny in gear, pushed in the clutch and the grinding stopped.
I also took the lid off, inspected the forks and thoroughly cleaned the inside but noise still continues.
Trans Sport :: Sound When Engaging Transmission / Forward And Specially Reverse
Just recently, my '93 transport 3800 has started making weird sounds when engaging transmission , forward...and specially reverse. This is not a transmission problem. It sounds like there is increased torsional movement of the engine/transmission unit and it made me take a look at the engine while would shift in drive and reverse....it does lean much..impressive ..but in fact I do not remember having tried looking for that before...so I cannot compare.
View 9 Replies