Ford F-150 (2004-2008) :: Random Misfires In Almost Every Cylinder
I have an 05 Lariat with 145k miles on it. About a month ago I had a misfire code on one cylinder. Since then it's gone from once every couple of days, various cylinders. To now every day. I've had to continue driving it but the last few days it's gotten bad and I hope I didn't do any more damage(cats) but I didn't have a whole lot of choice. I've read every thread I can find and haven't found an exact match. It seems to be worse first thing in the morning, it will be down on power for a few seconds then clear up. It may not return for another 10 or 15 minutes and then cough a little and clear up.
Sometimes it will start at the beginning of a hill and not clear up until I'm back on flat, sometimes it will lose power at the top. There is zero predictability to it. I have had codes on almost every cylinder, but no single one has dominated the problem. Twice when it has been real bad I have also gotten a lean code 0174. It had new Motorcraft plugs 25000 miles ago and has run fine until recently. The ticking isn't too bad but I think I'm going to try thicker oil for the summer. It's been a while since I did the fuel filter and since it probably isn't a bad idea I'm going to do that today.
Prius (2004-09) :: Misfires On Cylinder 1 And 3, Now 2 And 4
2005 Prius 195k miles, oil changes every 5k +/- 500 (usually minus), new plugs at about 187k, TSBs for coolant loop done, coolant valve for ICE replaced on my dime, replaced aux battery in 2010. Transaxle fluid changed at 100k and 190k due to noise, but that is another post.
I mostly do my own work because, in general, I find dealerships to charge too much (like one hour to change the aux battery) or not competent (like changing the traction battery under warranty but leaving the seat belt behind the panel or not resetting the maintenance light during 5k Toyota covered maintenance)
Ford Ranger / B-Series :: 1997 4WD - Cylinder Misfires On 4 And 6
Besides being spark plugs and wires and/or a bad coil pack, what other things could make it so i have misfires on cylinders 4 and 6? going to replace the plugs and wires later today when they get to my house but i just want to know what other things i could be so I can evaluate the potential repair cost and should the wires for cylinders 4,5, and 6 be under or over the intake manifold? I bought my truck used and they are currently under the manifold i think it would make more sense to have them over personally.
I have a 1997 Ranger 4WD with the 6 cylinder 4.0L engine. I can't remember the codes that it tripped at the moment but i think one might have been the 304 code not sure though.
I tripped the 300,304, and 306 code but don't know about any others i remembered what codes i tripped the other day when i had it scanned
Ford Excursion :: 2001 V10 - P0303 And P0307 Codes / Misfires On Cylinder 3 And 7
So on Christmas day I turned on my truck and all was well. I had family over and we were going up to my range to do some Christmas day target shooting. I let it warm up for about 20 minutes we then loaded up and headed out.
When I locked the hubs I soon found out my 4WD was not working? Due to the cold? It worked fine last time out and now not at all. I decided to forge ahead in 2WD, Sure enough we got stuck in deep snow. I had to gun the engine off and on to get out and as soon as I broke free (CHECK ENGINE) appeared for the first time ever. Worst Christmas ever!
The truck is running fine, full power and no irregular noise from the engine. So I ran the test and P0303, P0307 misfires on cylinder 3 and 7 appeared. This whole post is about me doing a full tune up this spring the truck is parked since Christmas and will stay parked until I do a full tune up.
New Plugs.
New Wires.
New Coils.
New oil filter and oil. Changed last year with less than 2000 miles but changing anyways.
Flush radiator and add new radiator fluid.
Clean air filter (Aftermarket, It is washable).
Is there anything I'm missing? Also, any tips on figuring out the 4WD issue?
Ford F-150 (2009-2014) :: Random Misfires On Cylinder 1 / 3 And 4 - Rough Idle
Ok so I have the 2009 f150 4.6l 2wd. Have random misfire codes. Horrid idle. I replaced all of the spark plugs, coil packs, and even the injectors on 1/3/4. Still codes nothing is better. I'm thinking maybe an intake manifold leak,? I see no real signs but I do hear that little pop pop pop. Now I have a gasket kit for it but I see you can order complete manifold kits with thermostat and gaskets on amazon for like 60 bucks more. The issue is I see none that fit my truck. Is it the same as the mustang? Hate to blow more cash as its adding up.
View 4 RepliesF Series :: F150 V6 4.2L Hard To Diagnose Engine Misfires?
Been a common problem for years and recently got one in the shop for the concern with the EGR port plugging up and then dumping all the egr into the one cylinder that is not plugged causing a misfire off idle. Many know of this concern but I have yet to see a good example of it. I show you some easy diagnosis before you pull the upper plenum to inspect the ports.
This video is hosted at YouTube . If the video does not play, wait a minute or try again later.
Golf IV R32 :: Misfires On Cylinder 5 And 6
How the cylinders are numbered as your facing the car from the front left to right (forgot the order) so I can replace coil packs on cyl 5&6 (238 misfires in 2min is not good).
View 4 RepliesFord Super Duty (1999-2016) :: 2003 F250 4x4 - Misfires On Cylinder 1 / 3 / 6 And 7 - Knock P0325
2003 F-250 SD 4x4 w/5.4L engine and 4R100 trans (pic in sig) . Truck has 280K on it with about 40K on a partial rebuild on the top end.
Took the truck out offroading and got about 4" from the top of the 33" tire in water (not mud.. water) . Someone with 6' tractor tore through the puddle.....
Well the truck survived through it ... albeit dirty as all hell and developed some issues soon thereafter. Codes for misfires on cyl 1,3,6,7, general ignition coil, etc etc etc
Power washed the underbody , washed the mud off the engine bay (yeah... with water but given it was caked with mud and water to fill the plug wells... no additional harm) .
Replaced all 8 COP and 4 plugs ( easier ones to reach), oil change, oil filter, new paper cone filter. checked most all the harness connections and cleaned with alcohol also. Reset the PCM/ECU and drove the truck for about 100miles and finally just after putting a full tank of gas (92 Octane) I throw a P0325...
The engine runs very clean, no hesitation, smooth idle, smooth acceleration on both light and hard acceleration. Just the damn code. Is it the gas I just topped off? After 100+ miles with new COP and plugs it threw nothing until this and runs great. Dont hear any knock/ping/detonation by ear and feels silky smooth at idle.
I really dont want to have to tear the intake off to replace bank 1 knock...
Ford Super Duty (1999-2016) :: Spark Plug On Cylinder 4 Is Sitting Level With Hole - Misfires
2001 Ford F350 V10, 220K in crap condition
First of all on the left side 2 of the coils were so withered the rubber separated from the bolt and were loose. Without any tools I was able to remove 2 coils. Typically there is the hole and several inches inside hole is where the spark plug sits.
On cylinder 4 the spark plug is on a funny angle and is level with the hole or possibly poking up above the hole. Tried sticking the ignition coil over the spark plug but it wasn't correct. Leaving it alone until my cousin can take a look. Spark plug was tight but I didn't put a ratchet on it.
Wondering, is this the infamous spark plug blew threw the cylinder thing. Wish I would have taken a picture (I will next time I'm with truck).
Had codes for misfires on 4 cylinders but that was with 2 coils unplugged (way I got truck at auction)....I replaced 3 of them (1/2/6).Cleared codes...4th cylinder remained unplugged....And the only code I got after letting truck idle for 10 minutes was something about ignition coil D (which would line up with cylinder 4 I think).
Hyundai - Elantra :: 2002 - Misfires On Cylinder 1
I have a 2002 Elantra that has been in shop 3xs for same thing. The car says it is missfiring on 1 and I have changed wires, coil pack and spark plugs with no success.
View 2 RepliesPassat (B5) :: Hesitate / Jerk A Little When Accelerated - Possible Cylinder Misfires
I drive a 99 1.8t Passat with 90,xxx miles. Yesterday I felt the car hesitate/jerk a little when it's accelerated to 35-40 miles per hour. I've had this problem in my past and it was a cylinder misfire. I would bring it to the repair shop.
My question is: Can my car last about 1.5 weeks? My work is 20 mins away. I can definitely avoid the freeway.
Golf IV R32 :: Cylinder 2 Sporadically Misfires When Accelerating Up To About 60mph
My Mk4 R32 has been in the shop for a week now. My number 2 cylinder began sporadically misfiring on the highway and then once I turned the engine off and then back on it would run fine until I got back on the highway and began to accelerate up to about 60.
Took it in and the mechanics couldn't replicate the code. Got a vacuum tube replaced and and it ran fine until I got to the highway. Same issue.
At this point the fuel injector has been replaced and its still throwing the code.
Accent LC (2000-05) :: 2003 - Cylinder 2 Misfires At Startup
My accent is misfiring at startup, and randomly at stoplights. Pulling the code tells me it's the #2 cylinder. I have no trouble at highway speeds, the car really drives fine outside of stoplights and startups. The idle hovers around 900 rpm. Sometimes, once I'm on the road and driving, the CEL will go away altogether.
My main question is, is there any way to be certain that it's the 2/3 coil pack? I don't want to spend on parts that won't fix anything.
Accent LC (2000-05) :: Getting Codes For Multiple Misfires On Cylinder 1 / 2 And 4
I have a 2000 lc 1.5l ... I just rebuilt the motor machine shop work and all it Will start and run for 3 seconds and then die. If I hold the gas pedal it will run but sound rough and as soon as you let go it dies I have been able to get codes multiple misfires, misfire cylinder 1, misfire cylinder 2, and misfire cylinder 4 I have put brand new plugs (copper core ngk), wires coils, crank sensor, cam sensor, iac, tps, maf and the injectors all have new orings it also has ntk o2 sensors that might have 1000 miles on them...
View 1 RepliesNissan - Altima :: 1999 - When Idling It Misfires On Cylinder 3
The car crank up normally, but when idling it misfires on #3 cylinder. When start to drive it will drive at 45 mph at full revolution but when I stop at a light the engine begins to vibrate and shakes the entire car. When moving off again, it continues to vibrate and hesitate and will not get up back in speed 25-30 mlp and now start to backfire in to the manifold. While stepping on the gas it also makes a popping sound. If I try to get the speed up any higher it will violently makes a popping sound and backfiring constantly into the manifold and struggles to go. The engine is also getting very hot although the engine gage said it normal and not overheating. If the car is sitting in a grassy area while idling it will completely burn dry the grass underneath.
View 12 RepliesBMW :: Cylinder 1 Misfires On Startup For Few Seconds Or Up To Few Minutes Under Certain Conditions
I have an intermittent start-up problem with my 2001 BMW Z-3, 3.0: cylinder 1 misfires on start-up for a few seconds or up to a few minutes under certain conditions. The misfire conditions are consistent:A)OBDII code P0313 (misfire detected with low fuel) or code PO1343 (cylinder 1 misfire with fuel cutoff). Both OBDII codes equate to BMW fault code 238.B)after winter storage it misfires on start–up for 5-10 minutes (I’ve always added a fuel stabilizer before winter storage);C)after a spike in humidity it misfires on start-up for a few seconds or up to a minute after a rain storm or;D)If I don’t run the car for a 3-5 days (always stored in a garage) it misfires for a few seconds (just long enough to turn on the “check engine” light).
Otherwise, the car runs flawlessly –plenty of power – smooth as silk - no hesitation, but with the bloody check engine light on 50% of the time.In lieu of black tape over the check engine indicator, I’ve taken the car alternately to both Minneapolis BMW dealers over the years (once if not twice a year), but the intermittent nature of the misfire and the fact that I store the car 5 months the a year has made it difficult to pin down the exact “root cause” of the problem. The dealership mechanics have swapped and/or replaced the cylinder 1 fuel injector, spark plug, cylinder coil and cable, kept it overnight and for days. The last dealership diagnosis was a defective cylinder 1 exhaust valve that could only be fixed with valve job! Yes, that’s right, pull the head and do a complete valve job - on all six cylinders. What am I missing here? What about the infamous BMW VANOS valve control system?
Civic - Honda :: 2002 EX Reading Misfires On 3 Cylinder And Cat Code
I have an 02 Civic EX. Engine light has been on for over a year, runs just fine. Reading misfires on 3 cyl, and cat code. I have since: changed all plugs and coils, changed both front and rear o2 sensors....switched coils around to see if code misfires changed (yes).
I see this is a common problem but no one has a solution..? I'd rather NOT change the cat converter and pay for that only to find out the light stays on. Need to smog so I can sell!
Subaru - Outback :: 2001 - Misfires On Right Side Only - Faulty Cylinder 1 / 3 And 5
I just bought a used 2001 Subaru Outback L.L.Bean, and the check-engine light is on due to misfiring in cylinders 1, 3, and 5 (right side only). I thought I was getting a pretty good deal even given the CEL risk, but the car is at the mechanic now and he is stumped and telling me I have to take it to a dealer service center.
This is a 6 cylinder with a timing chain. Plugs were replaced and computer reset and the light came right back on. There are no spark plug wires, and I read that the coil packs rarely fail. The engine runs smoothly and seems to have power, but since I just bought the car used so I'm not sure how much power is normal. It has 122k miles.
What could be causing misfires on one side of the engine only?
Passat (B5) :: 2002 - Getting Multiple CEL For Catalytic Converters And Cylinder Misfires
Getting multiple CEL's for the catalytic converters and cylinder misfires. Looking for threads that address these particular codes ie. 0431, 0421, 0300. 0303, 0306. I have a feeling that these are being caused from a vacuum leak and/or needing a reflash for the ECU.
View 3 Replies