Tiguan :: Random Cylinder Misfires On All Cylinders With Rough Idle
I have 11 tiguan 2.0T. When I start it up is runs rough below 1200 rpm. The check engine light starts flashing. The codes are all 4 cylinders for random cylinder misfire. When I go drive it around the roughness calms down but doesn't go away and the idle will start jumping up and down. It goes to 1500 back to 800. Then 1700 back to 800. It had even hit 2400 once. I have changed the pcv about 2 months ago. I checked it and it looks fine. One place said maf. I cleaned it and no change. Running out of options.
View 2 RepliesTiguan :: Running Rough During A Cold Start / Random Cylinder Misfires
I've got a 2009 Tiguan with 65k miles on it. A few weeks ago I noticed some issues with running rough during a cold start. I only noticed because the engine would vibrate considerably more than usually for the first few minutes of operation, and would idle at around 1050-1100rpm instead of the usual 750rpm. After warm up, things were fine. Suddenly the issue got bad real fast - wife was out and the MIL light came on, EPC light came on, and the car was running extremely rough. We managed to drive it home (2 miles) doing under 20 the whole time on side streets. Once I hooked it up to my OBD reader, I was seeing cylinder misfire codes on all four cylinders.. P0300, P0301..P0304, all five codes simultaneously.
Since the car was due for an oil change and hit 65k miles recently, I decided to throw new plugs in there to see if that would work. It did, at first.. A day or two it ran completely fine, no rough starts, no misfires, I thought I had solved the problem. The old plugs had some deposits on them and were original, so I thought I was in the clear. Two days later, same thing happened again.. EPC light, barely running and misfires on all four cylinders..
I read up some online and decided to order new ignition coils. Took a few days, but I got four new coils and threw them in. Again, problem solved it seemed. No more EPC light, misfire codes didn't come back and no more rough starts. I drove a good 40 miles with no problems at various speeds, but started noticing some misfires during acceleration (slightly rough acceleration, almost feels like a back and forth rocking motion, very slight). Sure enough, after a cold start I'm seeing the engine run a bit rough again with misfires. This time, only P0304 (misfire on cylinder 4) is thrown, and it only shows up as a "pending code" (engine light flashes for a few moments during start, but does not stay on).
I checked my connections, swapped the plugs and coils in what I thought were cylinders 3 and 4 (closer to the driver side), nothing. I swapped what I think are cylinder 1 and 2 (passenger side) just to be sure, but still nothing. At this point I'm pretty lost. I know enough to be dangerous with a carbureted engine, but am lacking in knowledge when it comes to a fuel injected turbo charged VW engine. It seems to be cylinder 4 misfiring consistently at this point according to the OBD reader.
Also of note.. I had some misfire problems last year, and had my intake manifold replaced as part of a recall (also had carbon deposits removed at the same time). Can a carbon build up occur this fast? Can it be the injectors?
Ford F-150 (2009-2014) :: Trans Slamming / Shudder / Random Misfires
Well, just picked the truck up from the dealer. Had to pay for the shudder diagnosis which turned up a #8 misfire as well as lesser random misfires on the mode 6 test (no CEL) since it out of B2B warranty. Also brought up the transmission issue I have been having. Virtually every morning when I go to pull out of the driveway, when I put the truck in park it was quite violently slamming into gear, even if I let it idle long enough to drop the neutral RPM's.
Service writer was a bit baffled, but after touching base with their driveline technician, and verifying it was in no way similar to how any other F150 engages they were able to locate TSB 11-11-11 which, to me, seems primarily concerned with the harsh 1-2 and 2-3 shifting but also noted the harsh engagement.
Anyways, they squeezed me in over night and in 2 days had my parts in and installed (apparently on these trucks they have to physically get the numbers off the solenoids to be replaced as there are a couple options). 3 solenoids tested bad and were replaced under the powertrain warranty. Truck did not slam when I picked it up, looking forward to testing tomorrow morning!
The best part is that when the tech went to drive the truck in this morning to start working it not only slammed into gear for him (verifying my concern) but it also demonstrated the violent 1-2 upshift. Too bad they couldn't push a spark plug through warranty, guess I'll have to wait for my Rockauto order to come in
Ford F-150 (2004-2008) :: Random Misfires In Almost Every Cylinder
I have an 05 Lariat with 145k miles on it. About a month ago I had a misfire code on one cylinder. Since then it's gone from once every couple of days, various cylinders. To now every day. I've had to continue driving it but the last few days it's gotten bad and I hope I didn't do any more damage(cats) but I didn't have a whole lot of choice. I've read every thread I can find and haven't found an exact match. It seems to be worse first thing in the morning, it will be down on power for a few seconds then clear up. It may not return for another 10 or 15 minutes and then cough a little and clear up.
Sometimes it will start at the beginning of a hill and not clear up until I'm back on flat, sometimes it will lose power at the top. There is zero predictability to it. I have had codes on almost every cylinder, but no single one has dominated the problem. Twice when it has been real bad I have also gotten a lean code 0174. It had new Motorcraft plugs 25000 miles ago and has run fine until recently. The ticking isn't too bad but I think I'm going to try thicker oil for the summer. It's been a while since I did the fuel filter and since it probably isn't a bad idea I'm going to do that today.
Prius (Gen 1) :: Auxiliary Battery Drained - Random / Multiple Cylinder Misfires Detected
I left the key on and drained my auxiliary battery(It was weak before) and when I jumped it it started and then shut off after ~20 seconds. I tried various different things and all I succeeded in doing was draining my HV battery from starting it so many times. So I disassembled the pack and recharged it and now it starts and runs but it is misfiring. It throwing 4 codes:
P0300: Random/Multiple Cylinder Misfire Detected
P0302: Cylinder 2 Misfire Detected
P0304: Cylinder 4 Misfire Detected
P1305: Ignition Coil 2 Primary Feedback Circuit
I inspected the igniters and plugs and they seem to be OK and I'm not sure where to look next. I'm not sure if the battery issue is related or not but I did replace the auxiliary battery.
Santa Fe (CM - 2007-12) :: 2009 - Rough Idle / Random Stalling
I am happy to own a Hyundai Santa Fe (2009) 2.7l which originally originated in the US. It is a really nice car, however, it recently over time developed the problem, which causes some pain - firstly it started with rough idle (pulsating), now it began to stall from time to time when decelerating.
[URL].....
I tried to plug a OBD reader and here's what I get (well, that's a "pending" fault, but still might be useful).
I tried to browse around the internet. I believe it is unlikely that 2 oxygen sensors fail at the same time. It could possibly be caused by vacuum leaks or faulty MAF. Is it a common fault among Santa Fe?
Passat (B6) :: Shakes At Idle - Multiple Random Misfires
So I took a trip from Dallas to Florida, and on the way back my check engine light came on. The car shakes at idle, almost like it wants to take off. I drove it back to Dallas like that since the car runs normal on the high way. I got it scanned at autozone and the code said it had multiple random misfires. I'll be taking to the dealer in the morning, but what it could be? The car jumped over 50K during the trip hopefully the dealer will be nice and cover it.
View 4 RepliesFord F-150 (2009-2014) :: 2010 - Rough Idle With AC On
2010 F150 4.6L 2V, 50k miles. Have recently developed an issue with an extremely rough idle with the AC on and trans in Drive. If in park, the idle is high enough that it is much less noticeable. I have cleaned my throttle body, and MAF sensor ? After this , I disconnected battery for about 30mins and let the computer reset. After a long drive today, it is still happening. This engine has the servo controlled throttle body, and therefore no IAC valve that I can identify. I would assume that the idle increase necessary for the AC to be on would come from the servo controlled throttle body itself with no need for an external IAC. The idle in Drive with the AC on will drop to 500 RPM or less and it is very rough. Is there a procedure for a recalibration of the servo throttle body that I could try ?
View 14 RepliesGolf IV / Jetta IV :: Multiple Random Misfires In All 4 Cylinders Came Up / Idle And Boost
I have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 RepliesFord F-150 (2009-2014) :: Idle Rough Sometimes Almost Feeling Like It Was Going To Stall Out
I have a 2013 with the 3.7 in it with 24,000 miles on it. I bought the truck used with 8,000 on it was a pre-Owned certified and it already had a k&n air intake which I know it's not needed and I would much rather have the factory intake instead.. 7 months ago I took it to the dealer because I noticed at stop lights it idled rough sometimes almost feeling like it was going to stall out so I took it in and they said that the motor was getting to much air and causing it to run like it was and they said the cooler weather was making it worse and said it should get better when it warms up and they said it wouldn't hurt anything... Well I live in Florida and it's been in the 90s and it still idles like crap you can feel the vibration through the truck...
And it's so aggravating and annoying and I wish I had a stock intake that I could install on the truck to see if it fixes the problem but I don't and I've researched the problem and have seen people with the same issues without the k&n air intake and I've also been told that the stock air intake gives the motor just as much air as the k&n so with that being said did the dealer take the easy way out and blame the intake or should they be responsible for installing the factory intake back on since they made it a certified pre-owned with the k&n on the truck? It's been frustrating because I don't know a whole lot about gas motors.. And I'd like to get the problem fixed while I still have warranty ..
Ford F-150 (2009-2014) :: Rough Idle - 049-.053 Park Plug Gap On 5.0?
My truck has a similar rough idle and I decided to investigate. What my plug gap was supposed to be as I didn't have access to my owners manual at the time. The specs I was given (.041-.047) is what I followed and recapped my plugs .045. The idle improved a great deal.
Now I was wondering and finally got around to checking my owners manual after I read somewhere that the gap for the 5.0 changed between 12 and 13 model years. What I found in my owners manual is that the gap I'm supposed to have is from .049-.053. My plugs were out anyway at .057. I will leave them be at .045 but am wondering why the change from .041-.047 on the 2011 model years to .049-.053 on the 2012+ model years? I assume the engine hasn't changed, so am curious of the thought process.
Ford F-150 (2009-2014) :: 2013 - At Startup Idle Rough?
2013 3.5 Ecoboost. Starting the truck first thing in the morning, it idles very rough for about 30 seconds and then smoothes out. If I drop it into gear it stays rough as I back out of the driveway. Once underway it runs fine and otherwise runs/idles very smooth for the rest of the day. Doesn't appear to have any other symptoms of spark plugs/boots misfire so I'm thinking it might be something else?
On my old 02 F150 with the 5.4 this usually happened when the Idle air control (IAC) would get plugged up with carbon. I'd clean it and the idle would smooth out. This truck doesn't appear to have one.
Spark plugs are on my list for the near future. 47k on the truck so they are almost geting due. Trying to get my superduty sold before I spend a lot of time on this truck.
Ford F-150 (2009-2014) :: 2012 - Rough Idle Upon Start Up - Injector Is Cutting In And Out Or Missing
2012 F-150 5.0 Rough Idle Upon Start up - YouTube
Whenever I first start my 2012 F-150 with the 5.0, it idles rough and if I step on the gas it acts like either an injector is cutting in and out or it's missing. It doesn't really seem like a miss though, more like an injector/fuel issue. What it could be. If I let it sit and idle it won't go away unless I step on the gas and get it > 2500rpm or so.
Ford F-150 (2009-2014) :: 2011 XLT - Idle Slightly Rough In Drive / Stall At Stop
I have a 2011 XLT 5.0 V8 with 133,260 miles. I have extended warranty for the next 12,000 miles...which is great because I drive about 400 miles a month... Anyhow it runs great but for one small issue (hopefully) that has been intermittent.
She likes to idle slightly rough in drive at a stop or very low speed, and in reverse at slow speed. If I don't maintain the RPM it will stall and the low oil pressure light will come on, which I imagine comes on because of the sudden stall.
I first noticed this while backing into my garage in the driveway, It would fluctuate in RPMs and if I didn't maintain the gas it would shut off. I took it to the dealer and all they were able to tell me was the Tranny fluid was low and it would cause it to shut off at incline because a sensor isn't detecting fluid in the tranny. I thought this was weird but being as I have never owned an F150, I didn't know better.
It was fine for a little over a month and it started doing it again at stop lights and backing into my driveway. It has become frequent but there is no issue driving at speed and on the freeway. There is no stuttering or shaking and if it weren't for the fluctuating RPM at a stop and the stalling, it would be hard to tell if there was an issue.
All I can note is that there is a clicking sound under the hood, if I remember correctly the last time this happened I was at a 1/4 tank of fuel like I am now, I also feel like it may be a throttle body issue, or some sort of air sensor, I plan on taking it to the dealer but I figure I would get a more informed answer on the forums.
I also hear this is a common issue with the 5.0s... I purchased the truck in December and since then I have only put 250 miles on it.
Ford F-150 (2009-2014) :: Ticking Noise At 800 To 1000 RPMs / Rough Idle Leads To Engine Fail
2010 F150 ... So I have the tick noise at rpm's 800-1000 at drive through, stops, etc. So I did research on it a few months ago and saw that it might be VCT's but should be able to drive. so I drove it waiting to save money and have it go to a shop. well this past weekend while coming home from work my oil light came on the pressure dropped to zero, I was on the highway so I drove about another mile to get off highway and once I got off my truck died. I had it towed to my house and I thought I blew my motor. So I started doing research here and found that the VCT's AND cam Phaser could be bad. so I replaced my VCT on driver side put it all back together it started and loud knock was gone. then after 5 mins it was back very loud knock!
So I shut it down and took apart the passenger side once I got the valve cover off I found the problem.... The bolt that holds the cam phaser in place snapped off and was riding along the camshaft. So I took that out and extracted remaining part of bolt. inspected my camshaft and it was really messed up. so I bought new Phaser and Camshaft. the camshaft just came in today and I am trying to put it back in. but the hole for the pin in the phaser doesn't line up and I cant spin the shaft to make it line up. should I spin the cam phaser? I marked the chain and the phaser is where it should be on chain, but with that bolt snapping off could that have thrown the timing off so my mark is no good? when I lay the camshaft in place it sits perfect and if I just move the phase over 2-3 links it will all fit together. Should I do that?
Ford F-150 (2009-2014) :: Ecoboost Misfires - Spark Plug Replacement?
Ok so besides intercooler condensation causing misfires this is the #1 reason for misfires on this engine. Any misfires on this engine has great potential to damage the catalyst and should not be taken lightly. As many know by now boosted engines are hard on the plugs be it iridium platinum whatever and you may find the need for new plugs by 50k miles. More so now as many are coming in with carbon tracking as this one had. In this video I walk you through the procedure to change out plugs on these engines with the revised plugs, gap specs and TSB that have all come out recently.
Ford F150 3.5L V6 Ecoboost Misfires: Spark Plug Replacement - YouTube...
Golf IV / Jetta IV :: 2005 GTI 1.8t - Rough Idle And Misfires
2005 gti 1.8t having really rough idle and misfires at idle fine while driving pulling codes:
P0300
P0301
P0302
P0304
Unplugged MAF and didn't make a difference...
Golf IV / Jetta IV :: Rough Start And Idle But No Misfires
I have an 03 vr6. I'm getting codes p0300, 0303, and 0304. I changed the plugs and the coils and still has changed nothing. In the morning when I first go to start the car it has a rough start and idles rough. But after letting it warm up it is fine. It drives perfectly fine, no misfires. None of this started happening until the car ran hot a few weeks ago. Did a compression test and everything came up fine. So would could my issue be? I'm at a loss here. I was thinking fuel issue but if it was a fuel issue, wouldn't it run rough all the time?
View 15 RepliesPassat (B5) :: Random And Cylinder 1 Misfire At Idle And Low RPM
1999 Passat 2.8L. New coil pack assembly, wires, plugs, valve cover gasket(oil in plug holes). Misfire at idle and low rpm. Driving at higher rpm's misfire seems to go away. Codes are random misfire and cyl 1 misfire. Need to know if I would get an injector code if a fault or If that motor has problem with faulty cams or springs or any other common problems. I am going to do a compression check this weekend I'll update that info.....
View 9 Replies