Deville :: 2000 - Codes Keep Showing Is Po300 Multiple Misfires?
My old pump wasnt building pressure so i put a new filter on and i switched wit a used one from an old car i had.key on engine off Pressure goes to 45 then instantly starts droppin? Once i turn key an do again same thing... Car is starting tho. fuel Pressure around 38 while idling. I pulled fuel rail up and looked for leakin injectors.. There was none yet pressure still bled down kinda quick. I also have my cat aloose to keep from messing it up any further. Only codes keep showing is po300 multiple misfires.
View 2 RepliesAccent MC (2006-11) :: 2008 - Multiple Cylinder Misfire Codes
We bought the car used for my youngest daughter and it had a couple of codes in it. 1st was the o2 sensor.. easy fix, grabbed an OEM one and stuck it in. Then there was the Cyl 2/ multiple cyl misfire codes that kept getting thrown.
I've seen a bunch of post about people pretty much doing the same things I started out with and still having a problem.....
1) Swapped around all the coils.. still got a #2 misfire... So, coils are good.
2) Swapped in NGK Platinum plugs with a .032 gap.... still getting misfire.
3) Replaced the crank shaft position sensor...... still misfire
4) Noticed that there was an Ebay injector in the #2 cyl...... when I pulled the plugs, that cyl was running a little lean..... bought an OEM injector to go back in there...... still getting misfire
SO, I tried using a propane torch head and putting out gas around the intake to search for vacuum leak and got no response....... so, for the heck of it, I went old school and grabbed a can of starting fluid and started spraying it on the intake around where it bolts to head... bam... found a vacuum leak on #2 cyl....... ordered an intake gasket off of ebay, spent about 3 hours on it pulling the intake and replacing the gasket,( the bolts had loosened up over time and there were small tears in the gasket allowing it to suck air) .. put the new gasket on, cleared the codes and it's been running perfect ever since.
Check for a vacuum leak where the intake manifold bolts to the head... might save time and money.
Accent LC (2000-05) :: 2003 - Cylinder 2 Misfires At Startup
My accent is misfiring at startup, and randomly at stoplights. Pulling the code tells me it's the #2 cylinder. I have no trouble at highway speeds, the car really drives fine outside of stoplights and startups. The idle hovers around 900 rpm. Sometimes, once I'm on the road and driving, the CEL will go away altogether.
My main question is, is there any way to be certain that it's the 2/3 coil pack? I don't want to spend on parts that won't fix anything.
Accent LC (2000-05) :: 2002 1.6L - Multiple Cylinder Misfire
Car threw a multiple cylinder misfire, changed plugs, wires, and then coil packs. Code keeps coming back.
View 12 RepliesPassat (B5) :: 2002 - Getting Multiple CEL For Catalytic Converters And Cylinder Misfires
Getting multiple CEL's for the catalytic converters and cylinder misfires. Looking for threads that address these particular codes ie. 0431, 0421, 0300. 0303, 0306. I have a feeling that these are being caused from a vacuum leak and/or needing a reflash for the ECU.
View 3 RepliesPrius (Gen 1) :: Auxiliary Battery Drained - Random / Multiple Cylinder Misfires Detected
I left the key on and drained my auxiliary battery(It was weak before) and when I jumped it it started and then shut off after ~20 seconds. I tried various different things and all I succeeded in doing was draining my HV battery from starting it so many times. So I disassembled the pack and recharged it and now it starts and runs but it is misfiring. It throwing 4 codes:
P0300: Random/Multiple Cylinder Misfire Detected
P0302: Cylinder 2 Misfire Detected
P0304: Cylinder 4 Misfire Detected
P1305: Ignition Coil 2 Primary Feedback Circuit
I inspected the igniters and plugs and they seem to be OK and I'm not sure where to look next. I'm not sure if the battery issue is related or not but I did replace the auxiliary battery.
Mercedes-benz - C-class :: 2003 - Multiple Cylinder Misfires And Poor Gas Mileage
I have a 2003 Mercedes c230 with low mileage 70000. This was its first season not garaged. About 2wks ago when very cold started abruptly to misfire badly at idle with poor gas mileage and modest loss of power. I got codes on OBD II for multiple cylinder misfires p0301-4 (all 4 cylinders). No other codes. Also the MAF and O2 sensors seems to be giving normal readings, and I cleaned the MAF sensor (didn't take off. cleaned through screen connected to air filter housing). 1 or 2 of the spark plugs seemed fouled as had black oily fuel on them and the O2 sensor voltage readings were consistently close to 0.9v (high meaning reading rich air/fuel right?). Changed all 4 plugs and swapped around ignition coils. Seems a little better but still misfire. O2 sensor voltage reads now consistently around 0.7v and the new plugs are dry but already blackened (indicating rich air/fuel I think).
View 11 RepliesAccent LC (2000-05) :: Codes PO441 / PO442 And Engine Cylinder Dead?
We have a 2000 Accent that is having some problems. Last year, I took it into our trusted mechanic, who told me that the engine was going downhill - one of the cylinders was dead (this was in response to us wanting to drive it to Texas for our daughter that was stationed there - we just wanted a tune-up). The car ran fine, and here we are a year later - and need a smog.
It does have a problem starting at times when we put fuel in it (at 1 particular gas station) and Hyundai told us it was an EVAP issue and it would cost us $622. (Hyundai NEVER mentioned anything regarding the engine issue). We never got it fixed because again, it only happens at that one station, so we try to avoid it - and the car runs great (it has 190k miles on it).
So now, we need to get it smogged. Same mechanic wouldn't do anything - I pulled codes off my reader and it only gave me the 2 441/442 codes. I cleared the CEL off the dash.
Now, my question is: Should I just take it back to Hyundai for them to do the smog and EVAP repair? Or should I try to have it smogged. I'm not willing to give up on it yet. I'm sure the mechanic thinks it is dying, but I've been told that the engine would run rough and vibrate if a cylinder was dead. Of course, reality may smack me upside the head, but it just runs fine except for the fuel issue, that I'm doubting him.
Ford Excursion :: 2001 V10 - P0303 And P0307 Codes / Misfires On Cylinder 3 And 7
So on Christmas day I turned on my truck and all was well. I had family over and we were going up to my range to do some Christmas day target shooting. I let it warm up for about 20 minutes we then loaded up and headed out.
When I locked the hubs I soon found out my 4WD was not working? Due to the cold? It worked fine last time out and now not at all. I decided to forge ahead in 2WD, Sure enough we got stuck in deep snow. I had to gun the engine off and on to get out and as soon as I broke free (CHECK ENGINE) appeared for the first time ever. Worst Christmas ever!
The truck is running fine, full power and no irregular noise from the engine. So I ran the test and P0303, P0307 misfires on cylinder 3 and 7 appeared. This whole post is about me doing a full tune up this spring the truck is parked since Christmas and will stay parked until I do a full tune up.
New Plugs.
New Wires.
New Coils.
New oil filter and oil. Changed last year with less than 2000 miles but changing anyways.
Flush radiator and add new radiator fluid.
Clean air filter (Aftermarket, It is washable).
Is there anything I'm missing? Also, any tips on figuring out the 4WD issue?
Accent MC (2006-11) :: Multiple Cylinder Misfire
My car has been really acting up lately (AGAIN) so I took it in to have it looked at and they came back and told me it had multiple cylinder misfire, and they wanted like $1200 to fix it. What in the world does that mean and what is entailed in fixing it? They mentioned doing a full maintenance on it.
View 9 RepliesFord Super Duty (1999-2016) :: 2000 F250 V10 - Multiple Misfires / Engine Shakes Quite Noticeably Over 40 MPH
I have spent alot of time looking through threads about v10's misfiring and have not been able to resolve my issue. I recently purchased a 2000 v10 f250 with about 220000 miles on it I bought it knowing it had one miss fire but now I have a total of three. Te truck has no problems accelerating but at a little over 40 mph the engine shakes quite noticeably and after 60 i5 seems to smooth out. After alot of reading I replaced all of my plugs and ignition coils, ran a can of sea foam through my gas tank and my intake with no change to the miss fires. I have started my trials with the fuel injectors by switching them from miss firing cylinders to ones that aren't. Some other information is my truck has no egr on my intake.
View 4 RepliesGolf VI R :: Engine Error Codes - Random / Multiple Cylinder Misfire Detected
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
Jeep - Liberty :: Idling Rough With No Error Codes - Multiple Cylinder Misfire
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
Lexus ES 2007-12 :: Random / Multiple Cylinder Misfire Detected - Error Codes On ES350
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
Accent MC (2006-11) :: Random / Multiple Cylinder Misfire Detected
I guess misfires are a rite of passage for these vehicles. I purchased it only a week ago. Welcome to Hyundai...
The car has 53k kms. It's throwing P0300 and P030X on all cylinders. There was one instance of P0128. The engine runs smoothly and doesn't seem to down on power, although I have nothing to compare it to. The only performance issue is that it acts as if there is a rev limiter at 6k rpm. It sputters and stops pulling above 6k. Strangely, it doesn't throw the codes under load. The light flashes while it's running steady-state.
I pulled the plugs and they appeared to be in excellent condition with no erosion of the electrodes. The ash is slightly more white than I would expect, making me wonder about it being excessively lean. I called the dealer. They told me that coils are problematic. Replacing the coils made no difference.
That lead me here. I found the thread "Check engine light flashes then stays solid," which referenced the ECM update.
Interestingly, of the codes mentioned on the TSB, the car is having all but the last two.
- P0300: Random/Multiple Cylinder Misfire Detected.
- P0301: Cylinder 1 - Misfire Detected.
- P0302: Cylinder 2 - Misfire Detected.
- P0303: Cylinder 3 - Misfire Detected.
- P0304: Cylinder 4 - Misfire Detected.
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature).
- P0328: Knock Sensor 1 Circuit High Input.
- P0461: Fuel Level Sensor A Circuit Range/Performance.
Ford Super Duty (1999-2016) :: 2008 F350 - Multiple Codes / Cylinder 5 Misfire
My dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.
Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.
My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.
Ford 6.0L Power Stroke Diesel :: CEL On For Multiple Codes - Cylinder 1 / 2 / 7 And 8 Have Glow Plug Circuit Open
Just got back from the beach yesterday. On the way back I noticed the check engine light on and read the codes. It listed 4 codes, P0671,P0672, P0677 and P0678. From what I can find, Cylinder 1, 2, 7 and 8 have the glow plug circuit open. Truck ran fine and didn't miss a beat. Ambient temp was around 80 when we started up the truck so I guess diesel plugs are not to crucial for that temp. I did notice when driving back the Vbatt would jump from 12.2v at1854 RPM (34 MPH) and 13.8v at 1652 (57 MPH).
Would bad batteries or low batteries cause this type of problem? This may be wishful thinking on my part. I have tested the batts with a DMM and they are at 12.3v. I took them out and charged them but they always go down to 12.3v. FMP is 47.5v to 48.5v. It seems suspect that all four glow plugs would be bad so I assume it could be the harness. What are some ways I can test to verify where the problems come from.First thing I would do is get two new batteries as these are still under warranty.
Toyota - Sienna :: 2000 - Check Engine Light Would Come At Times And Go Away / Multiple Error Codes
I have a 2000 Toyota Sienna that has had a check engine light for a while. The light would come at times, and go away at others, with prolonged intervals (days, weeks, months) with or without the light.
Suddenly it started losing power, especially on hills (even a small hill). The codes I read are (I include code interpretations from internet search):
P0300: Random or multiple misfire.
P0301: Cylinder 1 misfire.
P0304: Cylinder 4 misfire.
P1130: Air fuel sensor
P1150: I have not found a problem definition for this code.
Might these codes be indicative of a particular problem, or is each problem more likely a problem with its own cause?
Accent LC (2000-05) :: 2004 Chugging Like A Tractor / Exhaust Also Spits And Misfires
My problems started at the beginning of the year when my car for no reason would cut out each time i slowed down. Had a minor service done and it seems to have gotten worse. It now chugs like a tractor.
I have replaced/done:
Sparks
Coil pack
Fuel filter
Battery
Drive belts
Coil leads
Oil pickup filter
oil filter , New oil
I have also taken out the Crankshaft sensor and its fine.
Today i struggled to get my car home because it chugged that hard it felt like the car was going to stall. Its an automatic. I left it running in my drive way for about 10 minutes and it cut out, but it started back up straight away. It still continued chugging. The exhaust also spits and misfires.