Ford - Explorer :: 1996 - ABS Light Won't Go Off But No Error Codes
How do I get abs light to go off? I removed and cleaned all sensors, checked all wiring, fuses, and diode. I also used a a scanner, and it tells me there are no error codes. What do i do now?
View 12 RepliesFord F-150 - 1997-2003 :: Misfire Error Codes - CEL On?
Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors???
I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
Ford F-150 - 1997-2003 :: Error Codes - Misfire Detected On Cylinders 2 / 5 And 6
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
Ford F-150 - 1997-2003 :: Misfire Error Codes And Check Engine Light
So I have been having some troubles with my 2003 F150 4.6L ... Truck has been running rough and the check engine light was on so I decided to get the codes read and I got back P0302 and P0304, which from what I understand is a misfire on cylinders 3 & 4. At the same time I got Ford to do a little diagnostic and this is what they wrote for me:
"The connector for the number 2 coil is broken and will not stay plugged on to the coil and the number 2 coil is not working / replaced the wire for the coil still running rough removed the coil and plug. the plug was very badly fuel soaked started the vehicle to see if there was spark at the plug. OK. Suspect either a injector issue or a compression issue cleaned the plug seems better. "
So of course they quoted me for the works. They say I should replace the coils, plugs, and injectors??? I am pretty mechanically inclined and think I could change these things myself since I am on a budget. One tech told me is that the plugs can seize in these engines often and could scrap the whole thing??? Seems a little weird. If that happens though what could I do?
Accent MC (2006-11) :: Several Error Codes - Cylinder 3 Misfire
My 2011 Accent's engine light came on recently. The mechanic said it was a cylinder 3 misfire and recommend changing the spark plug and coil pack for that cylinder. We did that over the weekend. Now the light is back on and has read 5 codes in the past 12 hours (4 at one time). They are P0303, P0304, P0003, P0403, and P0100. I have looked the codes up and can't discern if any could be caused by one main issue. About a month ago it read a code for the oxy sensor, but it went away and never came back.
View 3 RepliesLexus RX 2004-09 :: P0355 Error Code And Potential Misfire Codes On All Cylinders
I am getting P0355 error code and potential misfire codes on all cylinders. Engine light and VSC stays on now. Idle is unstable and power is a little jerky at times. I bought a Denso direct ignition coil to replace, however, Cyl 5 looks difficult to access.
View 3 RepliesGolf VI R :: Engine Error Codes - Random / Multiple Cylinder Misfire Detected
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
Jeep - Liberty :: Idling Rough With No Error Codes - Multiple Cylinder Misfire
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
Lexus ES 2007-12 :: Random / Multiple Cylinder Misfire Detected - Error Codes On ES350
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
Ford F-150 (2004-2008) :: 1996 E150 - Oil Sending Unit Location?
where is the oil sending unit on a 1996 ford, E150, 5.0 motor.
View 1 RepliesSubaru - Intermittent - Misfire :: 1996 - Check Engine Light With Codes 0301 And 0303?
This is my friend's car and I have never looked under a Subaru hood before. She is getting an intermittent check engine light with codes for cylinder misfires on one and three. Today, I inspected the plugs and all four looked identical, a nice uniform tan color and good condition. No sign of deposits or oil. Did a compression test and found the driver's side bank at 155/150 and the passenger side bank at 185/190. My question at this point is which side is cylinders 1 and 3? The front-most cylinder is on the passenger side. Is this the number 1 and 3? If so, then the low compression on the other bank cannot account for the misfire.
View 5 RepliesFord - Explorer :: 1996 - Airbag Error Code B1944
I just pulled error code B1944 from my 96 Explorer. It says
Crash sensor ground
Ckt 1, High res/open
I found the airbag diagnostic module (in passenger cowl area) and checked for loosed wire, nothing found. Where the loose ground wire is located? I checked under the seat (didn't do a through job, but looked).
Ford/Mustang :: 1997 - Getting Error Code P0304 / Cylinder 4 Misfire
1997 Ford Mustang 4.6L EFI engine with 67K miles. The engine is actually now in a Factory Five Roadster. It sat on a stand for 5 years but runs well now with the exception of the code. I keep getting a code P0304 (cylinder 4 misfire) and I've checked the plug - the code seems accurate; it is misfiring.
Things I've tried:
1)swapped plugs,
2)this is a dual coil engine so I've swapped coils,
3)the #4 plug is the longest sparkplug wire so I've gotten high-performance wires,
4)heavily grounded the AL head,
5)put dielectric grease on the plug,
Still, ONLY cylinder 4 gives the misfire.
Ford - Mustang :: 2007 - Car Won't Go Over 3800 RPM / Error Codes Detected
I bought a gorgeous red 4.0L V-6 Mustang very cheap last week because it needed a clutch. I would not even pull the car. Little did I know that the clutch kit, including the slave cylinder and flywheel, was over $600. (But that's another story.)
The car runs now, but will not go over 3800 RPM in any gear. It had NINE codes, which they cleared. I was told that they primarily pointed to the MAF sensor. I cleaned it with the recommended aerosol. I have driven it 20 miles, and the MIL has not returned, but the little wrench symbol has. The Manual says to take it to the dealer (of course). The car seems to run fairly well, with the exception of the low rev limit. It is a "fly by wire" set up, with electronic throttle.
The cleared codes were P0102, P0113, P0135, P0141, P0155, P0161, P0403, P0443, and P0446. They actually repeated on Autozone's scanner. (My six year old Actron won't link to this car for some reason.
Ford - Expedition :: 1999 - Error Codes P0171 And P0174
I have a 1999 Ford Expedition with 163,000 miles.The vehicle registers a service code of P0171 and/or P0174, lean mixture.The vehicle starts fine, but may stall or hesitate when first started or at red lights.While driving, there is no issue.
I just replaced the MAF sensor and the EGR sensor, but no change in the condition.In 2007 or 50K miles ago, the oxygen sensors were replaced. What could be the problem or solution?
Ford Ranger / B-Series :: 1996 - 3rd Cylinder Misfire Intermittently
I figured something out on my ranger that has been bugging me for a while it was a third cly misfire so I changed the plugs and it went away for a while.the po told me he had just changed the plug wires so i didn't mess with those and it was an intermittent misfire so i changed the brain box because it was 15.00 at pull and save and it had been all updated boy did it run smooth for a while then the misfire came back. So I decided to check the 3rd cylinder plug wires and found out the one that is hard to change on the drivers side was badly rusted so i borrowed one off my windstar it was a little longer but boy does it run smoother and it doesn't die all the time and chug chug all the time now i just need to change the battery. i have already changed the clutch and the tranny twice i took one out of an 88 and it fit just fine by the way the engine is a 2.3 8 plug engine with over 230,000miles on it my next project is a timing belt and a heater core won't that be fun and yes i smell the antifreeze inside and don't like the stop leak like the last person put in.
View 2 RepliesFord 6.7L Power Stroke Diesel :: Got Error Codes P220c And P220e?
I had incorrect codes its a p200c and p200e
I know this has been talked about but im not having the same results when doing tests
Truck had a ruff fri night. Getting on I state with trailer loaded and it said STOP SAFELY NOW shut donw before i got it under 30 mph. Had it towed back to our shop and started to figure out what was wrong. I have heard of egt 12 and egt 13 sensors going bad. so i un plugged them and put a test meter to the first three all came back in the 216.00 range which is in standard for what my buddy's tested at.
Ford Ranger / B-Series :: 2000 - Got Error Codes PO731 And P1751?
I am having some issues with my 2000 Ford Ranger 2.5. It is throwing codes PO731 (Gear 1 incorrect ratio) P1751(shift solenoid a) PO 401 (EGR Valve & PO 1408 (EGR Valve Circuit Failure.
I recently replaced my valve body gasket because of harsh shifting from 1st to 2nd. The gasket was blown. After I replaced the gasket my truck ran better than it ever has before (like driving a new truck). Nice and smooth shifting! That lasted a couple days
Currently things have changed to the worse. My truck is shifting hard into 2nd. Has a huge loss of power during take off and seems bogged down. Also, my overdrive light will come on after driving for a couple of miles. So, I took my truck to the transmission shop to get the codes pulled. Which are all the codes listed above.
I figured I would attack the EGR issues as one and the transmission as another. I will also add that my EGR issues didn't just happen with the throttle body gasket change. This is something that has been going on way before. I have been at this for days now. I found tons of info on cleaning my EGR Valves and trouble shooting this system...so my main concern is the PO731 & P1751 Codes and how to deal with them.
Ford - Explorer :: Check Engine Light Came On But No Error Codes - How To Reset
My 1998 Explorer with 120,000 mile on it. The check light just came on. I have had several auto part stores plug in the scan tool and there were no error codes. I'm looking for the reset button location. I am also wondering should there be something missed by the scan tools, will the light activate should there be a real problem.
View 9 Replies